| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i40e: Fix DMA mappings leak
During reallocation of RX buffers, new DMA mappings are created for
those buffers.
steps for reproduction:
while :
do
for ((i=0; i<=8160; i=i+32))
do
ethtool -G enp130s0f0 rx $i tx $i
sleep 0.5
ethtool -g enp130s0f0
done
done
This resulted in crash:
i40e 0000:01:00.1: Unable to allocate memory for the Rx descriptor ring, size=65536
Driver BUG
WARNING: CPU: 0 PID: 4300 at net/core/xdp.c:141 xdp_rxq_info_unreg+0x43/0x50
Call Trace:
i40e_free_rx_resources+0x70/0x80 [i40e]
i40e_set_ringparam+0x27c/0x800 [i40e]
ethnl_set_rings+0x1b2/0x290
genl_family_rcv_msg_doit.isra.15+0x10f/0x150
genl_family_rcv_msg+0xb3/0x160
? rings_fill_reply+0x1a0/0x1a0
genl_rcv_msg+0x47/0x90
? genl_family_rcv_msg+0x160/0x160
netlink_rcv_skb+0x4c/0x120
genl_rcv+0x24/0x40
netlink_unicast+0x196/0x230
netlink_sendmsg+0x204/0x3d0
sock_sendmsg+0x4c/0x50
__sys_sendto+0xee/0x160
? handle_mm_fault+0xbe/0x1e0
? syscall_trace_enter+0x1d3/0x2c0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
RIP: 0033:0x7f5eac8b035b
Missing register, driver bug
WARNING: CPU: 0 PID: 4300 at net/core/xdp.c:119 xdp_rxq_info_unreg_mem_model+0x69/0x140
Call Trace:
xdp_rxq_info_unreg+0x1e/0x50
i40e_free_rx_resources+0x70/0x80 [i40e]
i40e_set_ringparam+0x27c/0x800 [i40e]
ethnl_set_rings+0x1b2/0x290
genl_family_rcv_msg_doit.isra.15+0x10f/0x150
genl_family_rcv_msg+0xb3/0x160
? rings_fill_reply+0x1a0/0x1a0
genl_rcv_msg+0x47/0x90
? genl_family_rcv_msg+0x160/0x160
netlink_rcv_skb+0x4c/0x120
genl_rcv+0x24/0x40
netlink_unicast+0x196/0x230
netlink_sendmsg+0x204/0x3d0
sock_sendmsg+0x4c/0x50
__sys_sendto+0xee/0x160
? handle_mm_fault+0xbe/0x1e0
? syscall_trace_enter+0x1d3/0x2c0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
RIP: 0033:0x7f5eac8b035b
This was caused because of new buffers with different RX ring count should
substitute older ones, but those buffers were freed in
i40e_configure_rx_ring and reallocated again with i40e_alloc_rx_bi,
thus kfree on rx_bi caused leak of already mapped DMA.
Fix this by reallocating ZC with rx_bi_zc struct when BPF program loads. Additionally
reallocate back to rx_bi when BPF program unloads.
If BPF program is loaded/unloaded and XSK pools are created, reallocate
RX queues accordingly in XSP_SETUP_XSK_POOL handler. |
| In the Linux kernel, the following vulnerability has been resolved:
can: j1939: j1939_tp_tx_dat_new(): fix out-of-bounds memory access
In the j1939_tp_tx_dat_new() function, an out-of-bounds memory access
could occur during the memcpy() operation if the size of skb->cb is
larger than the size of struct j1939_sk_buff_cb. This is because the
memcpy() operation uses the size of skb->cb, leading to a read beyond
the struct j1939_sk_buff_cb.
Updated the memcpy() operation to use the size of struct
j1939_sk_buff_cb instead of the size of skb->cb. This ensures that the
memcpy() operation only reads the memory within the bounds of struct
j1939_sk_buff_cb, preventing out-of-bounds memory access.
Additionally, add a BUILD_BUG_ON() to check that the size of skb->cb
is greater than or equal to the size of struct j1939_sk_buff_cb. This
ensures that the skb->cb buffer is large enough to hold the
j1939_sk_buff_cb structure.
[mkl: rephrase commit message] |
| In the Linux kernel, the following vulnerability has been resolved:
Revert "NFSD: Remove the cap on number of operations per NFSv4 COMPOUND"
I've found that pynfs COMP6 now leaves the connection or lease in a
strange state, which causes CLOSE9 to hang indefinitely. I've dug
into it a little, but I haven't been able to root-cause it yet.
However, I bisected to commit 48aab1606fa8 ("NFSD: Remove the cap on
number of operations per NFSv4 COMPOUND").
Tianshuo Han also reports a potential vulnerability when decoding
an NFSv4 COMPOUND. An attacker can place an arbitrarily large op
count in the COMPOUND header, which results in:
[ 51.410584] nfsd: vmalloc error: size 1209533382144, exceeds total
pages, mode:0xdc0(GFP_KERNEL|__GFP_ZERO),
nodemask=(null),cpuset=/,mems_allowed=0
when NFSD attempts to allocate the COMPOUND op array.
Let's restore the operation-per-COMPOUND limit, but increased to 200
for now. |
| In the Linux kernel, the following vulnerability has been resolved:
block: fix memory leak in __blkdev_issue_zero_pages
Move the fatal signal check before bio_alloc() to prevent a memory
leak when BLKDEV_ZERO_KILLABLE is set and a fatal signal is pending.
Previously, the bio was allocated before checking for a fatal signal.
If a signal was pending, the code would break out of the loop without
freeing or chaining the just-allocated bio, causing a memory leak.
This matches the pattern already used in __blkdev_issue_write_zeroes()
where the signal check precedes the allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: dice: fix buffer overflow in detect_stream_formats()
The function detect_stream_formats() reads the stream_count value directly
from a FireWire device without validating it. This can lead to
out-of-bounds writes when a malicious device provides a stream_count value
greater than MAX_STREAMS.
Fix by applying the same validation to both TX and RX stream counts in
detect_stream_formats(). |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: x86: s2idle: Catch multiple ACPI_TYPE_PACKAGE objects
If a badly constructed firmware includes multiple `ACPI_TYPE_PACKAGE`
objects while evaluating the AMD LPS0 _DSM, there will be a memory
leak. Explicitly guard against this. |
| The Qualys Cloud Agent included a bundled uninstall script (qagent_uninstall.sh), specific to Mac and Linux supported versions that invoked multiple system commands without using absolute paths and without sanitizing the $PATH environment. If the uninstall script is executed with elevated privileges (e.g., via sudo) in an environment where $PATH has been manipulated, an attacker with root/sudo privileges could cause malicious executables to be run in place of the intended system binaries. This behavior can be leveraged for local privilege escalation and arbitrary command execution under elevated privileges. |
| In the Linux kernel, the following vulnerability has been resolved:
futex: Don't leak robust_list pointer on exec race
sys_get_robust_list() and compat_get_robust_list() use ptrace_may_access()
to check if the calling task is allowed to access another task's
robust_list pointer. This check is racy against a concurrent exec() in the
target process.
During exec(), a task may transition from a non-privileged binary to a
privileged one (e.g., setuid binary) and its credentials/memory mappings
may change. If get_robust_list() performs ptrace_may_access() before
this transition, it may erroneously allow access to sensitive information
after the target becomes privileged.
A racy access allows an attacker to exploit a window during which
ptrace_may_access() passes before a target process transitions to a
privileged state via exec().
For example, consider a non-privileged task T that is about to execute a
setuid-root binary. An attacker task A calls get_robust_list(T) while T
is still unprivileged. Since ptrace_may_access() checks permissions
based on current credentials, it succeeds. However, if T begins exec
immediately afterwards, it becomes privileged and may change its memory
mappings. Because get_robust_list() proceeds to access T->robust_list
without synchronizing with exec() it may read user-space pointers from a
now-privileged process.
This violates the intended post-exec access restrictions and could
expose sensitive memory addresses or be used as a primitive in a larger
exploit chain. Consequently, the race can lead to unauthorized
disclosure of information across privilege boundaries and poses a
potential security risk.
Take a read lock on signal->exec_update_lock prior to invoking
ptrace_may_access() and accessing the robust_list/compat_robust_list.
This ensures that the target task's exec state remains stable during the
check, allowing for consistent and synchronized validation of
credentials. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix monitor mode bringup crash
When the interface is brought up in monitor mode, it leads
to NULL pointer dereference crash. This crash happens when
the packet type is extracted for a SKB. This extraction
which is present in the received msdu delivery path,is
not needed for the monitor ring packets since they are
all RAW packets. Hence appending the flags with
"RX_FLAG_ONLY_MONITOR" to skip that extraction.
Observed calltrace:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000064
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=0000000048517000
[0000000000000064] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
Modules linked in: ath11k_pci ath11k qmi_helpers
CPU: 2 PID: 1781 Comm: napi/-271 Not tainted
6.1.0-rc5-wt-ath-656295-gef907406320c-dirty #6
Hardware name: Qualcomm Technologies, Inc. IPQ8074/AP-HK10-C2 (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ath11k_hw_qcn9074_rx_desc_get_decap_type+0x34/0x60 [ath11k]
lr : ath11k_hw_qcn9074_rx_desc_get_decap_type+0x5c/0x60 [ath11k]
sp : ffff80000ef5bb10
x29: ffff80000ef5bb10 x28: 0000000000000000 x27: ffff000007baafa0
x26: ffff000014a91ed0 x25: 0000000000000000 x24: 0000000000000000
x23: ffff800002b77378 x22: ffff000014a91ec0 x21: ffff000006c8d600
x20: 0000000000000000 x19: ffff800002b77740 x18: 0000000000000006
x17: 736564203634343a x16: 656e694c20657079 x15: 0000000000000143
x14: 00000000ffffffea x13: ffff80000ef5b8b8 x12: ffff80000ef5b8c8
x11: ffff80000a591d30 x10: ffff80000a579d40 x9 : c0000000ffffefff
x8 : 0000000000000003 x7 : 0000000000017fe8 x6 : ffff80000a579ce8
x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 3a35ec12ed7f8900 x1 : 0000000000000000 x0 : 0000000000000052
Call trace:
ath11k_hw_qcn9074_rx_desc_get_decap_type+0x34/0x60 [ath11k]
ath11k_dp_rx_deliver_msdu.isra.42+0xa4/0x3d0 [ath11k]
ath11k_dp_rx_mon_deliver.isra.43+0x2f8/0x458 [ath11k]
ath11k_dp_rx_process_mon_rings+0x310/0x4c0 [ath11k]
ath11k_dp_service_srng+0x234/0x338 [ath11k]
ath11k_pcic_ext_grp_napi_poll+0x30/0xb8 [ath11k]
__napi_poll+0x5c/0x190
napi_threaded_poll+0xf0/0x118
kthread+0xf4/0x110
ret_from_fork+0x10/0x20
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl8xxxu: Fix memory leaks with RTL8723BU, RTL8192EU
The wifi + bluetooth combo chip RTL8723BU can leak memory (especially?)
when it's connected to a bluetooth audio device. The busy bluetooth
traffic generates lots of C2H (card to host) messages, which are not
freed correctly.
To fix this, move the dev_kfree_skb() call in rtl8xxxu_c2hcmd_callback()
inside the loop where skb_dequeue() is called.
The RTL8192EU leaks memory because the C2H messages are added to the
queue and left there forever. (This was fine in the past because it
probably wasn't sending any C2H messages until commit e542e66b7c2e
("wifi: rtl8xxxu: gen2: Turn on the rate control"). Since that commit
it sends a C2H message when the TX rate changes.)
To fix this, delete the check for rf_paths > 1 and the goto. Let the
function process the C2H messages from RTL8192EU like the ones from
the other chips.
Theoretically the RTL8188FU could also leak like RTL8723BU, but it
most likely doesn't send C2H messages frequently enough.
This change was tested with RTL8723BU by Erhard F. I tested it with
RTL8188FU and RTL8192EU. |
| NVIDIA Display Driver for Linux contains a vulnerability where an attacker might be able to use a race condition to escalate privileges. A successful exploit of this vulnerability might lead to code execution, escalation of privileges, data tampering, denial of service, and information disclosure. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: cfg80211: Pass the PMK in binary instead of hex
Apparently the hex passphrase mechanism does not work on newer
chips/firmware (e.g. BCM4387). It seems there was a simple way of
passing it in binary all along, so use that and avoid the hexification.
OpenBSD has been doing it like this from the beginning, so this should
work on all chips.
Also clear the structure before setting the PMK. This was leaking
uninitialized stack contents to the device. |
| The VAPIX Edge storage API that allowed a privilege escalation, enabling a VAPIX administrator-privileged user to gain Linux Root privileges. This flaw can only be exploited after authenticating with an administrator-privileged service account. |
| In the Linux kernel, the following vulnerability has been resolved:
pstore/ram: Add check for kstrdup
Add check for the return value of kstrdup() and return the error
if it fails in order to avoid NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: at91-sama5d2_adc: Fix potential use-after-free in sama5d2_adc driver
at91_adc_interrupt can call at91_adc_touch_data_handler function
to start the work by schedule_work(&st->touch_st.workq).
If we remove the module which will call at91_adc_remove to
make cleanup, it will free indio_dev through iio_device_unregister but
quite a bit later. While the work mentioned above will be used. The
sequence of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| at91_adc_workq_handler
at91_adc_remove |
iio_device_unregister(indio_dev) |
//free indio_dev a bit later |
| iio_push_to_buffers(indio_dev)
| //use indio_dev
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in at91_adc_remove. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() in case of error
If clk_get_rate() fails, the clk that has just been allocated needs to be
freed. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ina2xx: avoid NULL pointer dereference on OF device match
The affected lines were resulting in a NULL pointer dereference on our
platform because the device tree contained the following list of
compatible strings:
power-sensor@40 {
compatible = "ti,ina232", "ti,ina231";
...
};
Since the driver doesn't declare a compatible string "ti,ina232", the OF
matching succeeds on "ti,ina231". But the I2C device ID info is
populated via the first compatible string, cf. modalias population in
of_i2c_get_board_info(). Since there is no "ina232" entry in the legacy
I2C device ID table either, the struct i2c_device_id *id pointer in the
probe function is NULL.
Fix this by using the already populated type variable instead, which
points to the proper driver data. Since the name is also wanted, add a
generic one to the ina2xx_config table. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid5-cache: fix a deadlock in r5l_exit_log()
Commit b13015af94cf ("md/raid5-cache: Clear conf->log after finishing
work") introduce a new problem:
// caller hold reconfig_mutex
r5l_exit_log
flush_work(&log->disable_writeback_work)
r5c_disable_writeback_async
wait_event
/*
* conf->log is not NULL, and mddev_trylock()
* will fail, wait_event() can never pass.
*/
conf->log = NULL
Fix this problem by setting 'config->log' to NULL before wake_up() as it
used to be, so that wait_event() from r5c_disable_writeback_async() can
exist. In the meantime, move forward md_unregister_thread() so that
null-ptr-deref this commit fixed can still be fixed. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: zoned: skip splitting and logical rewriting on pre-alloc write
When doing a relocation, there is a chance that at the time of
btrfs_reloc_clone_csums(), there is no checksum for the corresponding
region.
In this case, btrfs_finish_ordered_zoned()'s sum points to an invalid item
and so ordered_extent's logical is set to some invalid value. Then,
btrfs_lookup_block_group() in btrfs_zone_finish_endio() failed to find a
block group and will hit an assert or a null pointer dereference as
following.
This can be reprodcued by running btrfs/028 several times (e.g, 4 to 16
times) with a null_blk setup. The device's zone size and capacity is set to
32 MB and the storage size is set to 5 GB on my setup.
KASAN: null-ptr-deref in range [0x0000000000000088-0x000000000000008f]
CPU: 6 PID: 3105720 Comm: kworker/u16:13 Tainted: G W 6.5.0-rc6-kts+ #1
Hardware name: Supermicro Super Server/X10SRL-F, BIOS 2.0 12/17/2015
Workqueue: btrfs-endio-write btrfs_work_helper [btrfs]
RIP: 0010:btrfs_zone_finish_endio.part.0+0x34/0x160 [btrfs]
Code: 41 54 49 89 fc 55 48 89 f5 53 e8 57 7d fc ff 48 8d b8 88 00 00 00 48 89 c3 48 b8 00 00 00 00 00
> 3c 02 00 0f 85 02 01 00 00 f6 83 88 00 00 00 01 0f 84 a8 00 00
RSP: 0018:ffff88833cf87b08 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000011 RSI: 0000000000000004 RDI: 0000000000000088
RBP: 0000000000000002 R08: 0000000000000001 R09: ffffed102877b827
R10: ffff888143bdc13b R11: ffff888125b1cbc0 R12: ffff888143bdc000
R13: 0000000000007000 R14: ffff888125b1cba8 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88881e500000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3ed85223d5 CR3: 00000001519b4005 CR4: 00000000001706e0
Call Trace:
<TASK>
? die_addr+0x3c/0xa0
? exc_general_protection+0x148/0x220
? asm_exc_general_protection+0x22/0x30
? btrfs_zone_finish_endio.part.0+0x34/0x160 [btrfs]
? btrfs_zone_finish_endio.part.0+0x19/0x160 [btrfs]
btrfs_finish_one_ordered+0x7b8/0x1de0 [btrfs]
? rcu_is_watching+0x11/0xb0
? lock_release+0x47a/0x620
? btrfs_finish_ordered_zoned+0x59b/0x800 [btrfs]
? __pfx_btrfs_finish_one_ordered+0x10/0x10 [btrfs]
? btrfs_finish_ordered_zoned+0x358/0x800 [btrfs]
? __smp_call_single_queue+0x124/0x350
? rcu_is_watching+0x11/0xb0
btrfs_work_helper+0x19f/0xc60 [btrfs]
? __pfx_try_to_wake_up+0x10/0x10
? _raw_spin_unlock_irq+0x24/0x50
? rcu_is_watching+0x11/0xb0
process_one_work+0x8c1/0x1430
? __pfx_lock_acquire+0x10/0x10
? __pfx_process_one_work+0x10/0x10
? __pfx_do_raw_spin_lock+0x10/0x10
? _raw_spin_lock_irq+0x52/0x60
worker_thread+0x100/0x12c0
? __kthread_parkme+0xc1/0x1f0
? __pfx_worker_thread+0x10/0x10
kthread+0x2ea/0x3c0
? __pfx_kthread+0x10/0x10
ret_from_fork+0x30/0x70
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
On the zoned mode, writing to pre-allocated region means data relocation
write. Such write always uses WRITE command so there is no need of splitting
and rewriting logical address. Thus, we can just skip the function for the
case. |
| Improper input validation in the Linux kernel-mode driver for some Intel(R) 800 Series Ethernet before version 1.17.2 may allow an authenticated user to potentially enable escalation of privilege via local access. |