| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: mscc: ocelot: add missing lock protection in ocelot_port_xmit_inj()
ocelot_port_xmit_inj() calls ocelot_can_inject() and
ocelot_port_inject_frame() without holding the injection group lock.
Both functions contain lockdep_assert_held() for the injection lock,
and the correct caller felix_port_deferred_xmit() properly acquires
the lock using ocelot_lock_inj_grp() before calling these functions.
Add ocelot_lock_inj_grp()/ocelot_unlock_inj_grp() around the register
injection path to fix the missing lock protection. The FDMA path is not
affected as it uses its own locking mechanism. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: skip ipv6 extension headers for csum checks
Protocol checksum validation fails for IPv6 if there are extension
headers before the protocol header. iph->len already contains its
offset, so use it to fix the problem. |
| In the Linux kernel, the following vulnerability has been resolved:
efi: Fix reservation of unaccepted memory table
The reserve_unaccepted() function incorrectly calculates the size of the
memblock reservation for the unaccepted memory table. It aligns the
size of the table, but fails to account for cases where the table's
starting physical address (efi.unaccepted) is not page-aligned.
If the table starts at an offset within a page and its end crosses into
a subsequent page that the aligned size does not cover, the end of the
table will not be reserved. This can lead to the table being overwritten
or inaccessible, causing a kernel panic in accept_memory().
This issue was observed when starting Intel TDX VMs with specific memory
sizes (e.g., > 64GB).
Fix this by calculating the end address first (including the unaligned
start) and then aligning it up, ensuring the entire range is covered
by the reservation. |
| In the Linux kernel, the following vulnerability has been resolved:
ata: libata-scsi: avoid Non-NCQ command starvation
When a non-NCQ command is issued while NCQ commands are being executed,
ata_scsi_qc_issue() indicates to the SCSI layer that the command issuing
should be deferred by returning SCSI_MLQUEUE_XXX_BUSY. This command
deferring is correct and as mandated by the ACS specifications since
NCQ and non-NCQ commands cannot be mixed.
However, in the case of a host adapter using multiple submission queues,
when the target device is under a constant load of NCQ commands, there
are no guarantees that requeueing the non-NCQ command will be executed
later and it may be deferred again repeatedly as other submission queues
can constantly issue NCQ commands from different CPUs ahead of the
non-NCQ command. This can lead to very long delays for the execution of
non-NCQ commands, and even complete starvation for these commands in the
worst case scenario.
Since the block layer and the SCSI layer do not distinguish between
queueable (NCQ) and non queueable (non-NCQ) commands, libata-scsi SAT
implementation must ensure forward progress for non-NCQ commands in the
presence of NCQ command traffic. This is similar to what SAS HBAs with a
hardware/firmware based SAT implementation do.
Implement such forward progress guarantee by limiting requeueing of
non-NCQ commands from ata_scsi_qc_issue(): when a non-NCQ command is
received and NCQ commands are in-flight, do not force a requeue of the
non-NCQ command by returning SCSI_MLQUEUE_XXX_BUSY and instead return 0
to indicate that the command was accepted but hold on to the qc using
the new deferred_qc field of struct ata_port.
This deferred qc will be issued using the work item deferred_qc_work
running the function ata_scsi_deferred_qc_work() once all in-flight
commands complete, which is checked with the port qc_defer() callback
return value indicating that no further delay is necessary. This check
is done using the helper function ata_scsi_schedule_deferred_qc() which
is called from ata_scsi_qc_complete(). This thus excludes this mechanism
from all internal non-NCQ commands issued by ATA EH.
When a port deferred_qc is non NULL, that is, the port has a command
waiting for the device queue to drain, the issuing of all incoming
commands (both NCQ and non-NCQ) is deferred using the regular busy
mechanism. This simplifies the code and also avoids potential denial of
service problems if a user issues too many non-NCQ commands.
Finally, whenever ata EH is scheduled, regardless of the reason, a
deferred qc is always requeued so that it can be retried once EH
completes. This is done by calling the function
ata_scsi_requeue_deferred_qc() from ata_eh_set_pending(). This avoids
the need for any special processing for the deferred qc in case of NCQ
error, link or device reset, or device timeout. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: don't zero the entire extent if EXT4_EXT_DATA_PARTIAL_VALID1
When allocating initialized blocks from a large unwritten extent, or
when splitting an unwritten extent during end I/O and converting it to
initialized, there is currently a potential issue of stale data if the
extent needs to be split in the middle.
0 A B N
[UUUUUUUUUUUU] U: unwritten extent
[--DDDDDDDD--] D: valid data
|<- ->| ----> this range needs to be initialized
ext4_split_extent() first try to split this extent at B with
EXT4_EXT_DATA_ENTIRE_VALID1 and EXT4_EXT_MAY_ZEROOUT flag set, but
ext4_split_extent_at() failed to split this extent due to temporary lack
of space. It zeroout B to N and mark the entire extent from 0 to N
as written.
0 A B N
[WWWWWWWWWWWW] W: written extent
[SSDDDDDDDDZZ] Z: zeroed, S: stale data
ext4_split_extent() then try to split this extent at A with
EXT4_EXT_DATA_VALID2 flag set. This time, it split successfully and left
a stale written extent from 0 to A.
0 A B N
[WW|WWWWWWWWWW]
[SS|DDDDDDDDZZ]
Fix this by pass EXT4_EXT_DATA_PARTIAL_VALID1 to ext4_split_extent_at()
when splitting at B, don't convert the entire extent to written and left
it as unwritten after zeroing out B to N. The remaining work is just
like the standard two-part split. ext4_split_extent() will pass the
EXT4_EXT_DATA_VALID2 flag when it calls ext4_split_extent_at() for the
second time, allowing it to properly handle the split. If the split is
successful, it will keep extent from 0 to A as unwritten. |
| In the Linux kernel, the following vulnerability has been resolved:
mfd: arizona: Fix regulator resource leak on wm5102_clear_write_sequencer() failure
The wm5102_clear_write_sequencer() helper may return an error
and just return, bypassing the cleanup sequence and causing
regulators to remain enabled, leading to a resource leak.
Change the direct return to jump to the err_reset label to
properly free the resources. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: pm8916_bms_vm: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle. |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: avoid per-cpu hold underflow in aa_get_buffer
When aa_get_buffer() pulls from the per-cpu list it unconditionally
decrements cache->hold. If hold reaches 0 while count is still non-zero,
the unsigned decrement wraps to UINT_MAX. This keeps hold non-zero for a
very long time, so aa_put_buffer() never returns buffers to the global
list, which can starve other CPUs and force repeated kmalloc(aa_g_path_max)
allocations.
Guard the decrement so hold never underflows. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: cpcap-battery: Fix use-after-free in power_supply_changed()
Using the `devm_` variant for requesting IRQ _before_ the `devm_`
variant for allocating/registering the `power_supply` handle, means that
the `power_supply` handle will be deallocated/unregistered _before_ the
interrupt handler (since `devm_` naturally deallocates in reverse
allocation order). This means that during removal, there is a race
condition where an interrupt can fire just _after_ the `power_supply`
handle has been freed, *but* just _before_ the corresponding
unregistration of the IRQ handler has run.
This will lead to the IRQ handler calling `power_supply_changed()` with
a freed `power_supply` handle. Which usually crashes the system or
otherwise silently corrupts the memory...
Note that there is a similar situation which can also happen during
`probe()`; the possibility of an interrupt firing _before_ registering
the `power_supply` handle. This would then lead to the nasty situation
of using the `power_supply` handle *uninitialized* in
`power_supply_changed()`.
Fix this racy use-after-free by making sure the IRQ is requested _after_
the registration of the `power_supply` handle. |
| In the Linux kernel, the following vulnerability has been resolved:
af_unix: Fix memleak of newsk in unix_stream_connect().
When prepare_peercred() fails in unix_stream_connect(),
unix_release_sock() is not called for newsk, and the memory
is leaked.
Let's move prepare_peercred() before unix_create1(). |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SDCA: Add allocation failure check for Entity name
Currently find_sdca_entity_iot() can allocate a string for the
Entity name but it doesn't check if that allocation succeeded.
Add the missing NULL check after the allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
net: annotate data-races around sk->sk_{data_ready,write_space}
skmsg (and probably other layers) are changing these pointers
while other cpus might read them concurrently.
Add corresponding READ_ONCE()/WRITE_ONCE() annotations
for UDP, TCP and AF_UNIX. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: Don't log plaintext credentials in cifs_set_cifscreds
When debug logging is enabled, cifs_set_cifscreds() logs the key
payload and exposes the plaintext username and password. Remove the
debug log to avoid exposing credentials. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: fix NULL pointer deref in ip6_rt_get_dev_rcu()
l3mdev_master_dev_rcu() can return NULL when the slave device is being
un-slaved from a VRF. All other callers deal with this, but we lost
the fallback to loopback in ip6_rt_pcpu_alloc() -> ip6_rt_get_dev_rcu()
with commit 4832c30d5458 ("net: ipv6: put host and anycast routes on
device with address").
KASAN: null-ptr-deref in range [0x0000000000000108-0x000000000000010f]
RIP: 0010:ip6_rt_pcpu_alloc (net/ipv6/route.c:1418)
Call Trace:
ip6_pol_route (net/ipv6/route.c:2318)
fib6_rule_lookup (net/ipv6/fib6_rules.c:115)
ip6_route_output_flags (net/ipv6/route.c:2607)
vrf_process_v6_outbound (drivers/net/vrf.c:437)
I was tempted to rework the un-slaving code to clear the flag first
and insert synchronize_rcu() before we remove the upper. But looks like
the explicit fallback to loopback_dev is an established pattern.
And I guess avoiding the synchronize_rcu() is nice, too. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/rocket: fix unwinding in error path in rocket_probe
When rocket_core_init() fails (as could be the case with EPROBE_DEFER),
we need to properly unwind by decrementing the counter we just
incremented and if this is the first core we failed to probe, remove the
rocket DRM device with rocket_device_fini() as well. This matches the
logic in rocket_remove(). Failing to properly unwind results in
out-of-bounds accesses. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: pm8001: Fix use-after-free in pm8001_queue_command()
Commit e29c47fe8946 ("scsi: pm8001: Simplify pm8001_task_exec()") refactors
pm8001_queue_command(), however it introduces a potential cause of a double
free scenario when it changes the function to return -ENODEV in case of phy
down/device gone state.
In this path, pm8001_queue_command() updates task status and calls
task_done to indicate to upper layer that the task has been handled.
However, this also frees the underlying SAS task. A -ENODEV is then
returned to the caller. When libsas sas_ata_qc_issue() receives this error
value, it assumes the task wasn't handled/queued by LLDD and proceeds to
clean up and free the task again, resulting in a double free.
Since pm8001_queue_command() handles the SAS task in this case, it should
return 0 to the caller indicating that the task has been handled. |
| In the Linux kernel, the following vulnerability has been resolved:
xen-netback: reject zero-queue configuration from guest
A malicious or buggy Xen guest can write "0" to the xenbus key
"multi-queue-num-queues". The connect() function in the backend only
validates the upper bound (requested_num_queues > xenvif_max_queues)
but not zero, allowing requested_num_queues=0 to reach
vzalloc(array_size(0, sizeof(struct xenvif_queue))), which triggers
WARN_ON_ONCE(!size) in __vmalloc_node_range().
On systems with panic_on_warn=1, this allows a guest-to-host denial
of service.
The Xen network interface specification requires
the queue count to be "greater than zero".
Add a zero check to match the validation already present
in xen-blkback, which has included this
guard since its multi-queue support was added. |
| In the Linux kernel, the following vulnerability has been resolved:
net: hns3: fix double free issue for tx spare buffer
In hns3_set_ringparam(), a temporary copy (tmp_rings) of the ring structure
is created for rollback. However, the tx_spare pointer in the original
ring handle is incorrectly left pointing to the old backup memory.
Later, if memory allocation fails in hns3_init_all_ring() during the setup,
the error path attempts to free all newly allocated rings. Since tx_spare
contains a stale (non-NULL) pointer from the backup, it is mistaken for
a newly allocated buffer and is erroneously freed, leading to a double-free
of the backup memory.
The root cause is that the tx_spare field was not cleared after its value
was saved in tmp_rings, leaving a dangling pointer.
Fix this by setting tx_spare to NULL in the original ring structure
when the creation of the new `tx_spare` fails. This ensures the
error cleanup path only frees genuinely newly allocated buffers. |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: Fix & Optimize table creation from possibly unaligned memory
Source blob may come from userspace and might be unaligned.
Try to optize the copying process by avoiding unaligned memory accesses.
- Added Fixes tag
- Added "Fix &" to description as this doesn't just optimize but fixes
a potential unaligned memory access
[jj: remove duplicate word "convert" in comment trigger checkpatch warning] |
| In the Linux kernel, the following vulnerability has been resolved:
quota: fix livelock between quotactl and freeze_super
When a filesystem is frozen, quotactl_block() enters a retry loop
waiting for the filesystem to thaw. It acquires s_umount, checks the
freeze state, drops s_umount and uses sb_start_write() - sb_end_write()
pair to wait for the unfreeze.
However, this retry loop can trigger a livelock issue, specifically on
kernels with preemption disabled.
The mechanism is as follows:
1. freeze_super() sets SB_FREEZE_WRITE and calls sb_wait_write().
2. sb_wait_write() calls percpu_down_write(), which initiates
synchronize_rcu().
3. Simultaneously, quotactl_block() spins in its retry loop, immediately
executing the sb_start_write() - sb_end_write() pair.
4. Because the kernel is non-preemptible and the loop contains no
scheduling points, quotactl_block() never yields the CPU. This
prevents that CPU from reaching an RCU quiescent state.
5. synchronize_rcu() in the freezer thread waits indefinitely for the
quotactl_block() CPU to report a quiescent state.
6. quotactl_block() spins indefinitely waiting for the freezer to
advance, which it cannot do as it is blocked on the RCU sync.
This results in a hang of the freezer process and 100% CPU usage by the
quota process.
While this can occur intermittently on multi-core systems, it is
reliably reproducing on a node with the following script, running both
the freezer and the quota toggle on the same CPU:
# mkfs.ext4 -O quota /dev/sda 2g && mkdir a_mount
# mount /dev/sda -o quota,usrquota,grpquota a_mount
# taskset -c 3 bash -c "while true; do xfs_freeze -f a_mount; \
xfs_freeze -u a_mount; done" &
# taskset -c 3 bash -c "while true; do quotaon a_mount; \
quotaoff a_mount; done" &
Adding cond_resched() to the retry loop fixes the issue. It acts as an
RCU quiescent state, allowing synchronize_rcu() in percpu_down_write()
to complete. |
