| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| Cross-Site Request Forgery (CSRF) vulnerability in Xylus Themes WP Event Aggregator.This issue affects WP Event Aggregator: from n/a through 1.7.6.
|
| Improper Neutralization of Input During Web Page Generation ('Cross-site Scripting') vulnerability in Xylus Themes WordPress Importer allows Stored XSS.This issue affects WordPress Importer: from n/a through 1.0.7.
|
| Cross-Site Request Forgery (CSRF) vulnerability in Extend Themes Teluro.This issue affects Teluro: from n/a through 1.0.31.
|
| Improper authorization vulnerability in Samsung Keyboard prior to version One UI 5.1.1 allows physical attackers to partially bypass the factory reset protection. |
| Improper handling of insufficient privileges vulnerability in TalkbackSE prior to version Android 14 allows local attackers to modify setting value of TalkbackSE. |
| Improper access control in some Intel(R) Ethernet Adapters and Intel(R) Ethernet Controller I225 Manageability firmware may allow a privileged user to potentially enable escalation of privilege via local access. |
| httparty before 0.21.0 is vulnerable to an assumed-immutable web parameter vulnerability. A remote and unauthenticated attacker can provide a crafted filename parameter during multipart/form-data uploads which could result in attacker controlled filenames being written. |
| In the Linux kernel, the following vulnerability has been resolved:
parisc: Revise gateway LWS calls to probe user read access
We use load and stbys,e instructions to trigger memory reference
interruptions without writing to memory. Because of the way read
access support is implemented, read access interruptions are only
triggered at privilege levels 2 and 3. The kernel and gateway
page execute at privilege level 0, so this code never triggers
a read access interruption. Thus, it is currently possible for
user code to execute a LWS compare and swap operation at an
address that is read protected at privilege level 3 (PRIV_USER).
Fix this by probing read access rights at privilege level 3 and
branching to lws_fault if access isn't allowed. |
| In the Linux kernel, the following vulnerability has been resolved:
parisc: Revise __get_user() to probe user read access
Because of the way read access support is implemented, read access
interruptions are only triggered at privilege levels 2 and 3. The
kernel executes at privilege level 0, so __get_user() never triggers
a read access interruption (code 26). Thus, it is currently possible
for user code to access a read protected address via a system call.
Fix this by probing read access rights at privilege level 3 (PRIV_USER)
and setting __gu_err to -EFAULT (-14) if access isn't allowed.
Note the cmpiclr instruction does a 32-bit compare because COND macro
doesn't work inside asm. |
| Auth. (admin+) Stored Cross-Site Scripting (XSS) vulnerability in Themepoints Testimonials plugin <= 2.6 on WordPress. |
| In the Linux kernel, the following vulnerability has been resolved:
vsock/virtio: Validate length in packet header before skb_put()
When receiving a vsock packet in the guest, only the virtqueue buffer
size is validated prior to virtio_vsock_skb_rx_put(). Unfortunately,
virtio_vsock_skb_rx_put() uses the length from the packet header as the
length argument to skb_put(), potentially resulting in SKB overflow if
the host has gone wonky.
Validate the length as advertised by the packet header before calling
virtio_vsock_skb_rx_put(). |
| Cross-Site Request Forgery (CSRF) vulnerability in Extend Themes EmpowerWP.This issue affects EmpowerWP: from n/a through 1.0.21. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: imu: bno055: fix OOB access of hw_xlate array
Fix a potential out-of-bounds array access of the hw_xlate array in
bno055.c.
In bno055_get_regmask(), hw_xlate was iterated over the length of the
vals array instead of the length of the hw_xlate array. In the case of
bno055_gyr_scale, the vals array is larger than the hw_xlate array,
so this could result in an out-of-bounds access. In practice, this
shouldn't happen though because a match should always be found which
breaks out of the for loop before it iterates beyond the end of the
hw_xlate array.
By adding a new hw_xlate_len field to the bno055_sysfs_attr, we can be
sure we are iterating over the correct length. |
| Server-Side Request Forgery (SSRF) vulnerability in Blossom Themes BlossomThemes Email Newsletter.This issue affects BlossomThemes Email Newsletter: from n/a through 2.2.6. |
| The httparty gem 0.9.0 and earlier for Ruby does not properly restrict casts of string values, which might allow remote attackers to conduct object-injection attacks and execute arbitrary code, or cause a denial of service (memory and CPU consumption) by leveraging Action Pack support for YAML type conversion, a similar vulnerability to CVE-2013-0156. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject %p% format string in bprintf-like helpers
static const char fmt[] = "%p%";
bpf_trace_printk(fmt, sizeof(fmt));
The above BPF program isn't rejected and causes a kernel warning at
runtime:
Please remove unsupported %\x00 in format string
WARNING: CPU: 1 PID: 7244 at lib/vsprintf.c:2680 format_decode+0x49c/0x5d0
This happens because bpf_bprintf_prepare skips over the second %,
detected as punctuation, while processing %p. This patch fixes it by
not skipping over punctuation. %\x00 is then processed in the next
iteration and rejected. |
| Unauth. Reflected Cross-Site Scripting vulnerability in Daniel Powney Multi Rating plugin <= 5.0.5 versions. |
| Cross-Site Request Forgery (CSRF) vulnerability in Daniel Powney Multi Rating plugin <= 5.0.5 versions. |
| httparty is an API tool. In versions 0.23.2 and prior, httparty is vulnerable to SSRF. This issue can pose a risk of leaking API keys, and it can also allow third parties to issue requests to internal servers. This issue has been patched via commit 0529bcd. |
| Cudy LT400 1.13.4 is vulnerable to Cross Site Scripting (XSS) in cgi-bin/luci/admin/network/wireless/config via the iface parameter. |
