| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: fix locking in hci_conn_request_evt() with HCI_PROTO_DEFER
When protocol sets HCI_PROTO_DEFER, hci_conn_request_evt() calls
hci_connect_cfm(conn) without hdev->lock. Generally hci_connect_cfm()
assumes it is held, and if conn is deleted concurrently -> UAF.
Only SCO and ISO set HCI_PROTO_DEFER and only for defer setup listen,
and HCI_EV_CONN_REQUEST is not generated for ISO. In the non-deferred
listening socket code paths, hci_connect_cfm(conn) is called with
hdev->lock held.
Fix by holding the lock. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: l2cap: Add missing chan lock in l2cap_ecred_reconf_rsp
l2cap_ecred_reconf_rsp() calls l2cap_chan_del() without holding
l2cap_chan_lock(). Every other l2cap_chan_del() caller in the file
acquires the lock first. A remote BLE device can send a crafted
L2CAP ECRED reconfiguration response to corrupt the channel list
while another thread is iterating it.
Add l2cap_chan_hold() and l2cap_chan_lock() before l2cap_chan_del(),
and l2cap_chan_unlock() and l2cap_chan_put() after, matching the
pattern used in l2cap_ecred_conn_rsp() and l2cap_conn_del(). |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: disable BH before calling udp_tunnel_xmit_skb()
udp_tunnel_xmit_skb() / udp_tunnel6_xmit_skb() are expected to run with
BH disabled. After commit 6f1a9140ecda ("add xmit recursion limit to
tunnel xmit functions"), on the path:
udp(6)_tunnel_xmit_skb() -> ip(6)tunnel_xmit()
dev_xmit_recursion_inc()/dec() must stay balanced on the same CPU.
Without local_bh_disable(), the context may move between CPUs, which can
break the inc/dec pairing. This may lead to incorrect recursion level
detection and cause packets to be dropped in ip(6)_tunnel_xmit() or
__dev_queue_xmit().
Fix it by disabling BH around both IPv4 and IPv6 SCTP UDP xmit paths.
In my testing, after enabling the SCTP over UDP:
# ip net exec ha sysctl -w net.sctp.udp_port=9899
# ip net exec ha sysctl -w net.sctp.encap_port=9899
# ip net exec hb sysctl -w net.sctp.udp_port=9899
# ip net exec hb sysctl -w net.sctp.encap_port=9899
# ip net exec ha iperf3 -s
- without this patch:
# ip net exec hb iperf3 -c 192.168.0.1 --sctp
[ 5] 0.00-10.00 sec 37.2 MBytes 31.2 Mbits/sec sender
[ 5] 0.00-10.00 sec 37.1 MBytes 31.1 Mbits/sec receiver
- with this patch:
# ip net exec hb iperf3 -c 192.168.0.1 --sctp
[ 5] 0.00-10.00 sec 3.14 GBytes 2.69 Gbits/sec sender
[ 5] 0.00-10.00 sec 3.14 GBytes 2.69 Gbits/sec receiver |
| In the Linux kernel, the following vulnerability has been resolved:
net, bpf: fix null-ptr-deref in xdp_master_redirect() for down master
syzkaller reported a kernel panic in bond_rr_gen_slave_id() reached via
xdp_master_redirect(). Full decoded trace:
https://syzkaller.appspot.com/bug?extid=80e046b8da2820b6ba73
bond_rr_gen_slave_id() dereferences bond->rr_tx_counter, a per-CPU
counter that bonding only allocates in bond_open() when the mode is
round-robin. If the bond device was never brought up, rr_tx_counter
stays NULL.
The XDP redirect path can still reach that code on a bond that was
never opened: bpf_master_redirect_enabled_key is a global static key,
so as soon as any bond device has native XDP attached, the
XDP_TX -> xdp_master_redirect() interception is enabled for every
slave system-wide. The path xdp_master_redirect() ->
bond_xdp_get_xmit_slave() -> bond_xdp_xmit_roundrobin_slave_get() ->
bond_rr_gen_slave_id() then runs against a bond that has no
rr_tx_counter and crashes.
Fix this in the generic xdp_master_redirect() by refusing to call into
the master's ->ndo_xdp_get_xmit_slave() when the master device is not
up. IFF_UP is only set after ->ndo_open() has successfully returned,
so this reliably excludes masters whose XDP state has not been fully
initialized. Drop the frame with XDP_ABORTED so the exception is
visible via trace_xdp_exception() rather than silently falling through.
This is not specific to bonding: any current or future master that
defers XDP state allocation to ->ndo_open() is protected. |
| In the Linux kernel, the following vulnerability has been resolved:
dm cache policy smq: fix missing locks in invalidating cache blocks
In passthrough mode, the policy invalidate_mapping operation is called
simultaneously from multiple workers, thus it should be protected by a
lock. Otherwise, we might end up with data races on the allocated blocks
counter, or even use-after-free issues with internal data structures
when doing concurrent writes.
Note that the existing FIXME in smq_invalidate_mapping() doesn't affect
passthrough mode since migration tasks don't exist there, but would need
attention if supporting fast device shrinking via suspend/resume without
target reloading.
Reproduce steps:
1. Create a cache device consisting of 1024 cache entries
dmsetup create cmeta --table "0 8192 linear /dev/sdc 0"
dmsetup create cdata --table "0 131072 linear /dev/sdc 8192"
dmsetup create corig --table "0 262144 linear /dev/sdc 262144"
dd if=/dev/zero of=/dev/mapper/cmeta bs=4k count=1 oflag=direct
dmsetup create cache --table "0 262144 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0"
2. Populate the cache, and record the number of cached blocks
fio --name=populate --filename=/dev/mapper/cache --rw=randwrite --bs=4k \
--size=64m --direct=1
nr_cached=$(dmsetup status cache | awk '{split($7, a, "/"); print a[1]}')
3. Reload the cache into passthrough mode
dmsetup suspend cache
dmsetup reload cache --table "0 262144 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 passthrough smq 0"
dmsetup resume cache
4. Write to the passthrough cache. By setting multiple jobs with I/O
size equal to the cache block size, cache blocks are invalidated
concurrently from different workers.
fio --filename=/dev/mapper/cache --name=test --rw=randwrite --bs=64k \
--direct=1 --numjobs=2 --randrepeat=0 --size=64m
5. Check if demoted matches cached block count. These numbers should
match but may differ due to the data race.
nr_demoted=$(dmsetup status cache | awk '{print $12}')
echo "$nr_cached, $nr_demoted" |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/riscv: Add IOTINVAL after updating DDT/PDT entries
Add riscv_iommu_iodir_iotinval() to perform required TLB and context cache
invalidations after updating DDT or PDT entries, as mandated by the RISC-V
IOMMU specification (Section 6.3.1 and 6.3.2). |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: hisilicon/sec2 - prevent req used-after-free for sec
During packet transmission, if the system is under heavy load,
the hardware might complete processing the packet and free the
request memory (req) before the transmission function finishes.
If the software subsequently accesses this req, a use-after-free
error will occur. The qp_ctx memory exists throughout the packet
sending process, so replace the req with the qp_ctx. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: Fix VM_BIND UNMAP locking
Wrong argument meant that the objs involved in UNMAP ops were not always
getting locked.
Since _NO_SHARE objs share a common resv with the VM (which is always
locked) this would only show up with non-_NO_SHARE BOs.
Patchwork: https://patchwork.freedesktop.org/patch/713898/ |
| In the Linux kernel, the following vulnerability has been resolved:
quota: Fix race of dquot_scan_active() with quota deactivation
dquot_scan_active() can race with quota deactivation in
quota_release_workfn() like:
CPU0 (quota_release_workfn) CPU1 (dquot_scan_active)
============================== ==============================
spin_lock(&dq_list_lock);
list_replace_init(
&releasing_dquots, &rls_head);
/* dquot X on rls_head,
dq_count == 0,
DQ_ACTIVE_B still set */
spin_unlock(&dq_list_lock);
synchronize_srcu(&dquot_srcu);
spin_lock(&dq_list_lock);
list_for_each_entry(dquot,
&inuse_list, dq_inuse) {
/* finds dquot X */
dquot_active(X) -> true
atomic_inc(&X->dq_count);
}
spin_unlock(&dq_list_lock);
spin_lock(&dq_list_lock);
dquot = list_first_entry(&rls_head);
WARN_ON_ONCE(atomic_read(&dquot->dq_count));
The problem is not only a cosmetic one as under memory pressure the
caller of dquot_scan_active() can end up working on freed dquot.
Fix the problem by making sure the dquot is removed from releasing list
when we acquire a reference to it. |
| In the Linux kernel, the following vulnerability has been resolved:
gfs2: add some missing log locking
Function gfs2_logd() calls the log flushing functions gfs2_ail1_start(),
gfs2_ail1_wait(), and gfs2_ail1_empty() without holding sdp->sd_log_flush_lock,
but these functions require exclusion against concurrent transactions.
To fix that, add a non-locking __gfs2_log_flush() function. Then, in
gfs2_logd(), take sdp->sd_log_flush_lock before calling the above mentioned log
flushing functions and __gfs2_log_flush(). |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix use-after-free from async crypto on Qualcomm crypto engine
ksmbd_crypt_message() sets a NULL completion callback on AEAD requests
and does not handle the -EINPROGRESS return code from async hardware
crypto engines like the Qualcomm Crypto Engine (QCE). When QCE returns
-EINPROGRESS, ksmbd treats it as an error and immediately frees the
request while the hardware DMA operation is still in flight. The DMA
completion callback then dereferences freed memory, causing a NULL
pointer crash:
pc : qce_skcipher_done+0x24/0x174
lr : vchan_complete+0x230/0x27c
...
el1h_64_irq+0x68/0x6c
ksmbd_free_work_struct+0x20/0x118 [ksmbd]
ksmbd_exit_file_cache+0x694/0xa4c [ksmbd]
Use the standard crypto_wait_req() pattern with crypto_req_done() as
the completion callback, matching the approach used by the SMB client
in fs/smb/client/smb2ops.c. This properly handles both synchronous
engines (immediate return) and async engines (-EINPROGRESS followed
by callback notification). |
| In the Linux kernel, the following vulnerability has been resolved:
memory: tegra124-emc: Fix dll_change check
The code checking whether the specified memory timing enables DLL
in the EMRS register was reversed. DLL is enabled if bit A0 is low.
Fix the check. |
| In the Linux kernel, the following vulnerability has been resolved:
soc/tegra: cbb: Fix incorrect ARRAY_SIZE in fabric lookup tables
Fix incorrect ARRAY_SIZE usage in fabric lookup tables which could
cause out-of-bounds access during target timeout lookup. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2/dlm: validate qr_numregions in dlm_match_regions()
Patch series "ocfs2/dlm: fix two bugs in dlm_match_regions()".
In dlm_match_regions(), the qr_numregions field from a DLM_QUERY_REGION
network message is used to drive loops over the qr_regions buffer without
sufficient validation. This series fixes two issues:
- Patch 1 adds a bounds check to reject messages where qr_numregions
exceeds O2NM_MAX_REGIONS. The o2net layer only validates message
byte length; it does not constrain field values, so a crafted message
can set qr_numregions up to 255 and trigger out-of-bounds reads past
the 1024-byte qr_regions buffer.
- Patch 2 fixes an off-by-one in the local-vs-remote comparison loop,
which uses '<=' instead of '<', reading one entry past the valid range
even when qr_numregions is within bounds.
This patch (of 2):
The qr_numregions field from a DLM_QUERY_REGION network message is used
directly as loop bounds in dlm_match_regions() without checking against
O2NM_MAX_REGIONS. Since qr_regions is sized for at most O2NM_MAX_REGIONS
(32) entries, a crafted message with qr_numregions > 32 causes
out-of-bounds reads past the qr_regions buffer.
Add a bounds check for qr_numregions before entering the loops. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: fix listxattr handling when the buffer is full
[BUG]
If an OCFS2 inode has both inline and block-based xattrs, listxattr()
can return a size larger than the caller's buffer when the inline names
consume that buffer exactly.
kernel BUG at mm/usercopy.c:102!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:usercopy_abort+0xb7/0xd0 mm/usercopy.c:102
Call Trace:
__check_heap_object+0xe3/0x120 mm/slub.c:8243
check_heap_object mm/usercopy.c:196 [inline]
__check_object_size mm/usercopy.c:250 [inline]
__check_object_size+0x5c5/0x780 mm/usercopy.c:215
check_object_size include/linux/ucopysize.h:22 [inline]
check_copy_size include/linux/ucopysize.h:59 [inline]
copy_to_user include/linux/uaccess.h:219 [inline]
listxattr+0xb0/0x170 fs/xattr.c:926
filename_listxattr fs/xattr.c:958 [inline]
path_listxattrat+0x137/0x320 fs/xattr.c:988
__do_sys_listxattr fs/xattr.c:1001 [inline]
__se_sys_listxattr fs/xattr.c:998 [inline]
__x64_sys_listxattr+0x7f/0xd0 fs/xattr.c:998
...
[CAUSE]
Commit 936b8834366e ("ocfs2: Refactor xattr list and remove
ocfs2_xattr_handler().") replaced the old per-handler list accounting
with ocfs2_xattr_list_entry(), but it kept using size == 0 to detect
probe mode.
That assumption stops being true once ocfs2_listxattr() finishes the
inline-xattr pass. If the inline names fill the caller buffer exactly,
the block-xattr pass runs with a non-NULL buffer and a remaining size of
zero. ocfs2_xattr_list_entry() then skips the bounds check, keeps
counting block names, and returns a positive size larger than the
supplied buffer.
[FIX]
Detect probe mode by testing whether the destination buffer pointer is
NULL instead of whether the remaining size is zero.
That restores the pre-refactor behavior and matches the OCFS2 getxattr
helpers. Once the remaining buffer reaches zero while more names are
left, the block-xattr pass now returns -ERANGE instead of reporting a
size larger than the allocated list buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: validate bg_bits during freefrag scan
[BUG]
A crafted filesystem can trigger an out-of-bounds bitmap walk when
OCFS2_IOC_INFO is issued with OCFS2_INFO_FL_NON_COHERENT.
BUG: KASAN: use-after-free in instrument_atomic_read include/linux/instrumented.h:68 [inline]
BUG: KASAN: use-after-free in _test_bit include/asm-generic/bitops/instrumented-non-atomic.h:141 [inline]
BUG: KASAN: use-after-free in test_bit_le include/asm-generic/bitops/le.h:21 [inline]
BUG: KASAN: use-after-free in ocfs2_info_freefrag_scan_chain fs/ocfs2/ioctl.c:495 [inline]
BUG: KASAN: use-after-free in ocfs2_info_freefrag_scan_bitmap fs/ocfs2/ioctl.c:588 [inline]
BUG: KASAN: use-after-free in ocfs2_info_handle_freefrag fs/ocfs2/ioctl.c:662 [inline]
BUG: KASAN: use-after-free in ocfs2_info_handle_request+0x1c66/0x3370 fs/ocfs2/ioctl.c:754
Read of size 8 at addr ffff888031bce000 by task syz.0.636/1435
Call Trace:
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0xbe/0x130 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xd1/0x650 mm/kasan/report.c:482
kasan_report+0xfb/0x140 mm/kasan/report.c:595
check_region_inline mm/kasan/generic.c:186 [inline]
kasan_check_range+0x11c/0x200 mm/kasan/generic.c:200
__kasan_check_read+0x11/0x20 mm/kasan/shadow.c:31
instrument_atomic_read include/linux/instrumented.h:68 [inline]
_test_bit include/asm-generic/bitops/instrumented-non-atomic.h:141 [inline]
test_bit_le include/asm-generic/bitops/le.h:21 [inline]
ocfs2_info_freefrag_scan_chain fs/ocfs2/ioctl.c:495 [inline]
ocfs2_info_freefrag_scan_bitmap fs/ocfs2/ioctl.c:588 [inline]
ocfs2_info_handle_freefrag fs/ocfs2/ioctl.c:662 [inline]
ocfs2_info_handle_request+0x1c66/0x3370 fs/ocfs2/ioctl.c:754
ocfs2_info_handle+0x18d/0x2a0 fs/ocfs2/ioctl.c:828
ocfs2_ioctl+0x632/0x6e0 fs/ocfs2/ioctl.c:913
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl fs/ioctl.c:583 [inline]
__x64_sys_ioctl+0x197/0x1e0 fs/ioctl.c:583
...
[CAUSE]
ocfs2_info_freefrag_scan_chain() uses on-disk bg_bits directly as the
bitmap scan limit. The coherent path reads group descriptors through
ocfs2_read_group_descriptor(), which validates the descriptor before
use. The non-coherent path uses ocfs2_read_blocks_sync() instead and
skips that validation, so an impossible bg_bits value can drive the
bitmap walk past the end of the block.
[FIX]
Compute the bitmap capacity from the filesystem format with
ocfs2_group_bitmap_size(), report descriptors whose bg_bits exceeds
that limit, and clamp the scan to the computed capacity. This keeps the
freefrag report going while avoiding reads beyond the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, arm64: Fix off-by-one in check_imm signed range check
check_imm(bits, imm) is used in the arm64 BPF JIT to verify that
a branch displacement (in arm64 instruction units) fits into the
signed N-bit immediate field of a B, B.cond or CBZ/CBNZ encoding
before it is handed to the encoder. The macro currently tests for
(imm > 0 && imm >> bits) || (imm < 0 && ~imm >> bits) which admits
values in [-2^N, 2^N) — effectively a signed (N+1)-bit range. A
signed N-bit field only holds [-2^(N-1), 2^(N-1)), so the check
admits one extra bit of range on each side.
In particular, for check_imm19(), values in [2^18, 2^19) slip past
the check but do not fit into the 19-bit signed imm19 field of
B.cond. aarch64_insn_encode_immediate() then masks the raw value
into the 19-bit field, setting bit 18 (the sign bit) and flipping
a forward branch into a backward one. Same class of issue exists
for check_imm26() and the B/BL encoding. Shift by (bits - 1)
instead of bits so the actual signed N-bit range is enforced. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Take state lock for af_unix iter
When a BPF iterator program updates a sockmap, there is a race condition in
unix_stream_bpf_update_proto() where the `peer` pointer can become stale[1]
during a state transition TCP_ESTABLISHED -> TCP_CLOSE.
CPU0 bpf CPU1 close
-------- ----------
// unix_stream_bpf_update_proto()
sk_pair = unix_peer(sk)
if (unlikely(!sk_pair))
return -EINVAL;
// unix_release_sock()
skpair = unix_peer(sk);
unix_peer(sk) = NULL;
sock_put(skpair)
sock_hold(sk_pair) // UaF
More practically, this fix guarantees that the iterator program is
consistently provided with a unix socket that remains stable during
iterator execution.
[1]:
BUG: KASAN: slab-use-after-free in unix_stream_bpf_update_proto+0x155/0x490
Write of size 4 at addr ffff8881178c9a00 by task test_progs/2231
Call Trace:
dump_stack_lvl+0x5d/0x80
print_report+0x170/0x4f3
kasan_report+0xe4/0x1c0
kasan_check_range+0x125/0x200
unix_stream_bpf_update_proto+0x155/0x490
sock_map_link+0x71c/0xec0
sock_map_update_common+0xbc/0x600
sock_map_update_elem+0x19a/0x1f0
bpf_prog_bbbf56096cdd4f01_selective_dump_unix+0x20c/0x217
bpf_iter_run_prog+0x21e/0xae0
bpf_iter_unix_seq_show+0x1e0/0x2a0
bpf_seq_read+0x42c/0x10d0
vfs_read+0x171/0xb20
ksys_read+0xff/0x200
do_syscall_64+0xf7/0x5e0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Allocated by task 2236:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_slab_alloc+0x63/0x80
kmem_cache_alloc_noprof+0x1d5/0x680
sk_prot_alloc+0x59/0x210
sk_alloc+0x34/0x470
unix_create1+0x86/0x8a0
unix_stream_connect+0x318/0x15b0
__sys_connect+0xfd/0x130
__x64_sys_connect+0x72/0xd0
do_syscall_64+0xf7/0x5e0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Freed by task 2236:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x70
__kasan_slab_free+0x47/0x70
kmem_cache_free+0x11c/0x590
__sk_destruct+0x432/0x6e0
unix_release_sock+0x9b3/0xf60
unix_release+0x8a/0xf0
__sock_release+0xb0/0x270
sock_close+0x18/0x20
__fput+0x36e/0xac0
fput_close_sync+0xe5/0x1a0
__x64_sys_close+0x7d/0xd0
do_syscall_64+0xf7/0x5e0
entry_SYSCALL_64_after_hwframe+0x76/0x7e |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Validate node_id in arena_alloc_pages()
arena_alloc_pages() accepts a plain int node_id and forwards it through
the entire allocation chain without any bounds checking.
Validate node_id before passing it down the allocation chain in
arena_alloc_pages(). |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: fix nfs4_file access extra count in nfsd4_add_rdaccess_to_wrdeleg
In nfsd4_add_rdaccess_to_wrdeleg, if fp->fi_fds[O_RDONLY] is already
set by another thread, __nfs4_file_get_access should not be called
to increment the nfs4_file access count since that was already done
by the thread that added READ access to the file. The extra fi_access
count in nfs4_file can prevent the corresponding nfsd_file from being
freed.
When stopping nfs-server service, these extra access counts trigger a
BUG in kmem_cache_destroy() that shows nfsd_file object remaining on
__kmem_cache_shutdown.
This problem can be reproduced by running the Git project's test
suite over NFS. |
