| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Input: elan_i2c - validate firmware size before use
Ensure that the firmware file is large enough to contain the expected
number of pages and the signature (which resides at the end of the
firmware blob) before accessing them to prevent potential out-of-bounds
reads. |
| In the Linux kernel, the following vulnerability has been resolved:
drivers/base/memory: set mem->altmap after successful device registration
If __add_memory_block() fails at xa_store() (under memory pressure for
example), device_unregister() is called, which eventually triggers
memory_block_release() with mem->altmap still set, causing a
WARN_ON(mem->altmap). This was triggered by modifying virtio-mem driver.
Fix this by delaying the assignment of mem->altmap until after
__add_memory_block() has succeeded. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: hyper-v: Bound the bank index when querying sparse banks
When checking if a VP ID is included in a sparse bank set, explicitly check
that the ID can actually be contained in a sparse bank (the TLFS allows for
a maximum of 64 banks of 64 vCPUs each). When handling a paravirtual TLB
flush for L2, the VP ID is copied verbatim from the enlightened VMCS,
without any bounds check, i.e. isn't guaranteed to be under the limit of
4096.
Failure to check the bounds of the VP ID leads to an out-of-bounds read
when testing the sparse bank, and super strictly speaking could lead to KVM
performing an unnecessary TLB flush for an L2 vCPU.
==================================================================
BUG: KASAN: use-after-free in hv_is_vp_in_sparse_set+0x85/0x100 [kvm]
Read of size 8 at addr ffff88811ba5f598 by task hyperv_evmcs/2802
CPU: 12 UID: 1000 PID: 2802 Comm: hyperv_evmcs Not tainted 7.1.0-rc2 #7 PREEMPT
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Call Trace:
<TASK>
dump_stack_lvl+0x51/0x60
print_report+0xcb/0x5d0
kasan_report+0xb4/0xe0
kasan_check_range+0x35/0x1b0
hv_is_vp_in_sparse_set+0x85/0x100 [kvm]
kvm_hv_flush_tlb+0xe9e/0x16c0 [kvm]
kvm_hv_hypercall+0xe6b/0x1e60 [kvm]
vmx_handle_exit+0x485/0x1b60 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x22e3/0x5070 [kvm]
kvm_vcpu_ioctl+0x5d0/0x10c0 [kvm]
__x64_sys_ioctl+0x129/0x1a0
do_syscall_64+0xb9/0xcf0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f0e62d1a9bf
</TASK>
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0xffffffffffffffff pfn:0x11ba5f
flags: 0x4000000000000000(zone=1)
raw: 4000000000000000 0000000000000000 00000000ffffffff 0000000000000000
raw: ffffffffffffffff 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88811ba5f480: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff88811ba5f500: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff88811ba5f580: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
^
ffff88811ba5f600: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff88811ba5f680: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
==================================================================
Disabling lock debugging due to kernel taint
Opportunistically add a compile time assertion to ensure the maximum number
of sparse banks exactly matches the number of possible bits in the passed
in mask.
[sean: add KASAN splat, drop comment, add assert, massage changelog] |
| In the Linux kernel, the following vulnerability has been resolved:
MIPS: smp: report dying CPU to RCU in stop_this_cpu()
smp_send_stop() parks all secondary CPUs in stop_this_cpu(). The function
marks the CPU offline for the scheduler via set_cpu_online(false) but
never informs RCU, so RCU keeps expecting a quiescent state from CPUs
that are now spinning forever with interrupts disabled.
As long as nothing waits for an RCU grace period after smp_send_stop()
this is harmless, which is why it went unnoticed. Since commit
91840be8f710 ("irq_work: Fix use-after-free in irq_work_single() on PREEMPT_RT")
however, irq_work_sync() calls synchronize_rcu() on architectures without
an irq_work self-IPI, i.e. where arch_irq_work_has_interrupt() returns
false. That is the asm-generic default used by MIPS. Any irq_work_sync()
issued in the reboot/shutdown path after smp_send_stop() then blocks on
a grace period that can never complete, hanging the reboot:
WARNING: CPU: 0 PID: 15 at kernel/irq_work.c:144 irq_work_queue_on
...
rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
rcu: Offline CPU 1 blocking current GP.
rcu: Offline CPU 2 blocking current GP.
rcu: Offline CPU 3 blocking current GP.
This issue was noticed on several Realtek MIPS switch SoCs (MIPS
interAptiv) and came up during kernel bump downstream in OpenWrt from
6.18.33 to 6.18.34, after the backport of the patch to the 6.18 stable
branch. The patch also has been backported all the way back to 6.1.
Call rcutree_report_cpu_dead() once interrupts are disabled, mirroring the
generic CPU-hotplug offline path, so RCU stops waiting on the parked CPUs
and grace periods can still complete. MIPS shuts down all CPUs here
without going through the CPU-hotplug mechanism, so this report is not
otherwise issued. Reporting a dying CPU to RCU outside the regular hotplug
offline path is not unprecedented: arm64 does the same in cpu_die_early().
There it is an exception for a CPU that was coming online and is aborting
bringup, rather than the default shutdown action as on MIPS. |
| In the Linux kernel, the following vulnerability has been resolved:
kernel/fork: clear PF_BLOCK_TS in copy_process()
PF_BLOCK_TS is only set in blk_time_get_ns() when current->plug is
non-NULL, and blk_finish_plug() clears it via __blk_flush_plug()
before NULLing the plug pointer. copy_process() breaks the
invariant by inheriting PF_BLOCK_TS from the parent while resetting
the child's plug to NULL.
Clear PF_BLOCK_TS alongside that assignment so callers can rely on
"PF_BLOCK_TS set implies current->plug != NULL" and dereference
current->plug unguarded. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: don't wrap around quota ids in dqiterate
LOLLM noticed that q_id is an unsigned 32-bit variable. If it happens
to be set to XFS_DQ_ID_MAX due to a filesystem that actually has a dquot
for ID_MAX, then this addition will truncate to zero and the iteration
starts over. Fix this by casting to u64. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: reject overlapping data areas in SMB2 responses
Commit 53b7c271f06b ("smb: client: restrict implied bcc[0] exemption to
responses without data area") restricted the implied bcc[0] length
exception to responses without a data area. However, the overlap
handling in __smb2_calc_size() clears data_length, which can make an
invalid response appear to have no data area and so qualify for the
exception.
Track data area overlap separately and reject such responses before
applying the length compatibility exceptions. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: remove request-less entries from ent_w_req_queue to fix NULL deref
If a copy into the userspace ring buffer fails, a request will be
terminated and fuse_uring_req_end() will set ent->fuse_req to NULL but
it will leave the entry on ent_w_req_queue in FRRS_FUSE_REQ state. This
can lead to a NULL deref if the request expiration logic scans
ent_w_req_queue in the window before the entry is moved off it.
Fix this by taking the entry off ent_w_req_queue and changing its state
from FRRS_FUSE_REQ to FRRS_INVALID before terminating the request. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: Avoid use-after-free in fuse_uring_async_stop_queues
fuse_uring_async_stop_queues() might run when the last reference
on ring->queue_refs was already dropped.
In order to avoid an early destruction a reference on struct fuse_conn
is now taken before starting fuse_uring_async_stop_queues() and that
reference is only released when that delayed work queue terminates. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: end fuse_req on io-uring cancel task work
When io_uring delivers task work with tw.cancel set (PF_EXITING,
PF_KTHREAD fallback, or percpu_ref_is_dying on the ring context),
fuse_uring_send_in_task() takes the cancel branch, assigns
-ECANCELED, and falls through to fuse_uring_send(). That path only
flips the entry to FRRS_USERSPACE and completes the io_uring cmd;
it never discharges the ring entry's owning reference to the
fuse_req that fuse_uring_add_req_to_ring_ent() handed it at
dispatch time.
fuse_uring_send_in_task()
tw.cancel == true
err = -ECANCELED
fuse_uring_send(ent, cmd, err, issue_flags)
ent->state = FRRS_USERSPACE
list_move(&ent->list, &queue->ent_in_userspace)
ent->cmd = NULL
io_uring_cmd_done(-ECANCELED)
/* ent->fuse_req still set, req still hashed */
The fuse_req stays linked on fpq->processing[hash] and
fuse_request_end() is never invoked. The originating syscall
thread blocks in D-state in request_wait_answer() until
fuse_abort_conn() runs, which can be the entire connection
lifetime. For FR_BACKGROUND requests fc->num_background is never
decremented either, so repeated cancels inflate the counter until
max_background is hit and all later background ops stall. tw.cancel does
not imply a connection abort (e.g. a single io_uring worker thread exits
while the fuse connection stays up), so this cannot be left for
fuse_abort_conn() to clean up.
Ending the req but still routing the entry through fuse_uring_send()
is not enough: that leaves a req-less entry on ent_in_userspace, and
ent_list_request_expired() dereferences ent->fuse_req unconditionally
on the head of that list, which would then NULL-deref.
Fix the cancel branch to release the entry directly. Remove it from the
queue, complete the io_uring cmd, end the fuse_req, free the entry, and
drop its queue_refs (waking the teardown waiter if it was the last). |
| In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: fix EFAULT clobber in fuse_uring_commit
copy_from_user() returns the number of bytes not copied as an unsigned
residual on failure (1..sizeof(struct fuse_out_header)). fuse_uring_commit
stores that residual in ssize_t err, sets req->out.h.error to -EFAULT,
then jumps to out: with err still holding the positive residual.
err = copy_from_user(&req->out.h, &ent->headers->in_out,
sizeof(req->out.h));
if (err) {
req->out.h.error = -EFAULT;
goto out; /* err is the positive residual */
}
...
out:
fuse_uring_req_end(ent, req, err);
fuse_uring_req_end() then runs
if (error)
req->out.h.error = error;
which overwrites the just-assigned -EFAULT with the positive residual.
FUSE callers such as fuse_simple_request() test err < 0 to detect
failure, so the positive value is interpreted as success and the
caller proceeds with an uninitialised or partial req->out.args.
Fix by assigning err = -EFAULT in the failure branch before jumping
to out, so fuse_uring_req_end() receives a negative errno and sets
req->out.h.error to -EFAULT. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: bound Read Response placement to the RREAD length
In drivers/infiniband/sw/siw/siw_qp_rx.c, siw_proc_rresp() places each
inbound Read Response DDP segment at sge->laddr + wqe->processed and then
accumulates wqe->processed, but it never checks the running total against
the sink buffer length on continuation segments. siw_check_sge() resolves
and validates the sink memory only on the first fragment (the if (!*mem)
branch), and siw_rresp_check_ntoh() compares the cumulative length against
wqe->bytes only on the final segment (the !frx->more_ddp_segs guard).
A connected siw peer that answers an outstanding RREAD with Read Response
segments that keep the DDP Last flag clear, carrying more total payload
than the RREAD requested, drives wqe->processed past the validated sink
buffer; the next siw_rx_data() call writes out of bounds at
sge->laddr + wqe->processed. siw runs iWARP over ordinary routable TCP,
so the peer is the remote end of an established RDMA connection and needs
no local privilege.
Bound every segment before placement, exactly as siw_proc_send() and
siw_proc_write() already do for their tagged and untagged paths, and
terminate the connection with a base-or-bounds DDP error when the
Read Response would overrun the sink buffer.
This is the second receive-path length fix for this file. A separate
change rejects an MPA FPDU length that underflows the per-fragment
remainder in the header decode; that guard does not cover this case,
because here each individual segment length is self-consistent and only
the accumulated placement offset overruns the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rtrs-srv: Bound RDMA-Write length to chunk size in rdma_write_sg
When the server answers an RTRS READ, rdma_write_sg() builds the source
scatter/gather entry for the IB_WR_RDMA_WRITE that returns data to the
peer. Its length is taken directly from the wire descriptor:
plist->length = le32_to_cpu(id->rd_msg->desc[0].len);
rd_msg points into the chunk buffer that the remote peer filled via
RDMA-WRITE-WITH-IMM (rtrs_srv_rdma_done() -> process_io_req() ->
process_read()), so desc[0].len is attacker-controlled and, before this
change, was only rejected when zero. The source address is the fixed
chunk start (dma_addr[msg_id]) and the source lkey is the PD-wide
local_dma_lkey, which is not tied to the chunk's MR mapping, so the verbs
layer does not constrain the transfer length to max_chunk_size. msg_id
and off are bounded against queue_depth and max_chunk_size in
rtrs_srv_rdma_done(), but desc[0].len is a separate field that was not
checked against the chunk size.
A peer that advertises desc[0].len larger than max_chunk_size can make
the posted RDMA write read past the chunk's mapped region. The resulting
behaviour depends on the IOMMU configuration: with no IOMMU or in
passthrough mode the read may extend into memory adjacent to the chunk
and be returned to the peer, which can disclose host memory; with a
translating IOMMU the out-of-range access is expected to fault and abort
the connection. In either case the transfer exceeds what the protocol
permits and is driven by a remote peer.
Reject a descriptor length above max_chunk_size, mirroring the existing
off >= max_chunk_size bound in rtrs_srv_rdma_done(). Legitimate clients
do not exceed it: the client sets desc[0].len to its MR length, which is
capped at the negotiated max_io_size (max_chunk_size - MAX_HDR_SIZE). |
| In the Linux kernel, the following vulnerability has been resolved:
Input: touchwin - reset the packet index on every complete packet
tw_interrupt() accumulates each non-zero serial byte into a fixed
three-byte buffer with a running index that is only reset once a full
packet has been received *and* the device's two Y bytes agree:
tw->data[tw->idx++] = data;
if (tw->idx == TW_LENGTH && tw->data[1] == tw->data[2]) {
...
tw->idx = 0;
}
The reset is gated on tw->data[1] == tw->data[2], a value the device
controls. A malicious, malfunctioning or counterfeit Touchwindow
peripheral can stream non-zero bytes whose 2nd and 3rd bytes differ: the
index reaches TW_LENGTH without the equality holding, is never reset, and
keeps growing, so tw->data[tw->idx++] walks off the end of the three-byte
array and the rest of the heap-allocated struct tw, one attacker-chosen
byte at a time -- an unbounded, device-driven heap out-of-bounds write.
Reset the index on every completed packet and report an event only when
the two Y bytes match, like the other serio touchscreen drivers do. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - fix touch indexing for MMS134S and MMS136
The MMS134S and MMS136 touch controllers have an event size of 6 bytes
rather than 8 bytes. When __mms114_read_reg() reads the touch data
packet from the device into the touch buffer, the events are packed
tightly at 6-byte intervals. However, the driver iterates through the
events using standard C array indexing (touch[index]), where each
element is sizeof(struct mms114_touch) (8 bytes) apart. As a result, any
touch events beyond the first one are read from incorrect offsets and
parsed improperly.
Fix this by explicitly calculating the byte offset for each touch event
based on the device's specific event size. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - bound the F3A keymap to the GPIO count
rmi_f3a_initialize() takes the GPIO count from the device query register
(f3a->gpio_count = buf & RMI_F3A_GPIO_COUNT, range 0..127).
rmi_f3a_map_gpios() then allocates gpio_key_map with
min(gpio_count, TRACKSTICK_RANGE_END) == at most 6 entries, but
rmi_f3a_attention() iterates the full gpio_count and dereferences
gpio_key_map[i], and input->keycodemax is set to the full gpio_count
while input->keycode points at the 6-entry allocation.
A device that reports gpio_count > 6 therefore causes an out-of-bounds
read of gpio_key_map[] on every attention interrupt, and out-of-bounds
accesses through the input core's default keymap ioctls: EVIOCGKEYCODE
reads past the buffer (leaking adjacent slab memory to user space) and
EVIOCSKEYCODE writes a caller-controlled value past it, for any process
able to open the evdev node, since input_default_getkeycode() and
input_default_setkeycode() only bound the index against keycodemax.
Size the keymap for the full gpio_count. The mapping loop is unchanged:
it still assigns only the first min(gpio_count, TRACKSTICK_RANGE_END)
entries; the remaining slots stay KEY_RESERVED (devm_kcalloc zero-fills)
and are skipped when reporting. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: imx-lpi2c: mark I2C adapter when hardware is powered down
On some i.MX platforms, certain I2C client drivers keep a periodic
workqueue which continues to trigger I2C transfers.
During system suspend/resume, there exists a time window between:
- suspend_noirq and the system entering suspend
- the system starting to resume and resume_noirq
In this window, the I2C controller resources such as clock and pinctrl
may already be disabled or not yet restored.
If a workqueue triggers an I2C transfer in this period, the driver
attempts to access I2C registers while the hardware resources are
unavailable, which may lead to system hang.
Mark the I2C adapter as suspended during noirq suspend and block new
transfers until resume, ensuring that I2C transfers are only issued
when hardware resources are available. |
| In the Linux kernel, the following vulnerability has been resolved:
fpga: dfl-afu: validate DMA mapping length in afu_dma_map_region()
afu_ioctl_dma_map() accepts a 64-bit length from userspace via
DFL_FPGA_PORT_DMA_MAP ioctl without an upper bound check. The value
is passed to afu_dma_pin_pages() where npages is derived as
length >> PAGE_SHIFT and passed to pin_user_pages_fast() which takes
int nr_pages, causing implicit truncation if length is very large.
Validate map.length at the ioctl entry point before calling
afu_dma_map_region(), rejecting values whose page count exceeds
INT_MAX. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Don't leak PFN when kvm_translate_vncr() races MMU notifier
In the case that kvm_translate_vncr() races with an MMU notifier the
early return does not release a reference on the faulted in PFN. Add
the necessary call to kvm_release_faultin_page() for the unused PFN. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Pin source page for write when adding CPUID data for SNP guest
When populating a guest_memfd instance with the initial CPUID data for an
SNP guest, acquire a writable pin on the source page as KVM will write back
the "correct" CPUID information if the userspace provided data is rejected
by trusted firmware. Because KVM writes to the source page using a kernel
mapping, pinning for read could result in KVM clobbering read-only memory.
Note, well-behaved VMMs are unlikely to be affected, as CPUID information
is almost always dynamically generated by userspace, i.e. it's unlikely for
the CPUID information to be backed by a read-only mapping.
[sean: rewrite shortlog and changelog, tag for stable@] |
