| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
x86/apic: Don't disable x2APIC if locked
The APIC supports two modes, legacy APIC (or xAPIC), and Extended APIC
(or x2APIC). X2APIC mode is mostly compatible with legacy APIC, but
it disables the memory-mapped APIC interface in favor of one that uses
MSRs. The APIC mode is controlled by the EXT bit in the APIC MSR.
The MMIO/xAPIC interface has some problems, most notably the APIC LEAK
[1]. This bug allows an attacker to use the APIC MMIO interface to
extract data from the SGX enclave.
Introduce support for a new feature that will allow the BIOS to lock
the APIC in x2APIC mode. If the APIC is locked in x2APIC mode and the
kernel tries to disable the APIC or revert to legacy APIC mode a GP
fault will occur.
Introduce support for a new MSR (IA32_XAPIC_DISABLE_STATUS) and handle
the new locked mode when the LEGACY_XAPIC_DISABLED bit is set by
preventing the kernel from trying to disable the x2APIC.
On platforms with the IA32_XAPIC_DISABLE_STATUS MSR, if SGX or TDX are
enabled the LEGACY_XAPIC_DISABLED will be set by the BIOS. If
legacy APIC is required, then it SGX and TDX need to be disabled in the
BIOS.
[1]: https://aepicleak.com/aepicleak.pdf |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix pci device refcount leak
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
So before returning from amdgpu_device_resume|suspend_display_audio(),
pci_dev_put() is called to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ar5523: Fix use-after-free on ar5523_cmd() timed out
syzkaller reported use-after-free with the stack trace like below [1]:
[ 38.960489][ C3] ==================================================================
[ 38.963216][ C3] BUG: KASAN: use-after-free in ar5523_cmd_tx_cb+0x220/0x240
[ 38.964950][ C3] Read of size 8 at addr ffff888048e03450 by task swapper/3/0
[ 38.966363][ C3]
[ 38.967053][ C3] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 6.0.0-09039-ga6afa4199d3d-dirty #18
[ 38.968464][ C3] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-1.fc36 04/01/2014
[ 38.969959][ C3] Call Trace:
[ 38.970841][ C3] <IRQ>
[ 38.971663][ C3] dump_stack_lvl+0xfc/0x174
[ 38.972620][ C3] print_report.cold+0x2c3/0x752
[ 38.973626][ C3] ? ar5523_cmd_tx_cb+0x220/0x240
[ 38.974644][ C3] kasan_report+0xb1/0x1d0
[ 38.975720][ C3] ? ar5523_cmd_tx_cb+0x220/0x240
[ 38.976831][ C3] ar5523_cmd_tx_cb+0x220/0x240
[ 38.978412][ C3] __usb_hcd_giveback_urb+0x353/0x5b0
[ 38.979755][ C3] usb_hcd_giveback_urb+0x385/0x430
[ 38.981266][ C3] dummy_timer+0x140c/0x34e0
[ 38.982925][ C3] ? notifier_call_chain+0xb5/0x1e0
[ 38.984761][ C3] ? rcu_read_lock_sched_held+0xb/0x60
[ 38.986242][ C3] ? lock_release+0x51c/0x790
[ 38.987323][ C3] ? _raw_read_unlock_irqrestore+0x37/0x70
[ 38.988483][ C3] ? __wake_up_common_lock+0xde/0x130
[ 38.989621][ C3] ? reacquire_held_locks+0x4a0/0x4a0
[ 38.990777][ C3] ? lock_acquire+0x472/0x550
[ 38.991919][ C3] ? rcu_read_lock_sched_held+0xb/0x60
[ 38.993138][ C3] ? lock_acquire+0x472/0x550
[ 38.994890][ C3] ? dummy_urb_enqueue+0x860/0x860
[ 38.996266][ C3] ? do_raw_spin_unlock+0x16f/0x230
[ 38.997670][ C3] ? dummy_urb_enqueue+0x860/0x860
[ 38.999116][ C3] call_timer_fn+0x1a0/0x6a0
[ 39.000668][ C3] ? add_timer_on+0x4a0/0x4a0
[ 39.002137][ C3] ? reacquire_held_locks+0x4a0/0x4a0
[ 39.003809][ C3] ? __next_timer_interrupt+0x226/0x2a0
[ 39.005509][ C3] __run_timers.part.0+0x69a/0xac0
[ 39.007025][ C3] ? dummy_urb_enqueue+0x860/0x860
[ 39.008716][ C3] ? call_timer_fn+0x6a0/0x6a0
[ 39.010254][ C3] ? cpuacct_percpu_seq_show+0x10/0x10
[ 39.011795][ C3] ? kvm_sched_clock_read+0x14/0x40
[ 39.013277][ C3] ? sched_clock_cpu+0x69/0x2b0
[ 39.014724][ C3] run_timer_softirq+0xb6/0x1d0
[ 39.016196][ C3] __do_softirq+0x1d2/0x9be
[ 39.017616][ C3] __irq_exit_rcu+0xeb/0x190
[ 39.019004][ C3] irq_exit_rcu+0x5/0x20
[ 39.020361][ C3] sysvec_apic_timer_interrupt+0x8f/0xb0
[ 39.021965][ C3] </IRQ>
[ 39.023237][ C3] <TASK>
In ar5523_probe(), ar5523_host_available() calls ar5523_cmd() as below
(there are other functions which finally call ar5523_cmd()):
ar5523_probe()
-> ar5523_host_available()
-> ar5523_cmd_read()
-> ar5523_cmd()
If ar5523_cmd() timed out, then ar5523_host_available() failed and
ar5523_probe() freed the device structure. So, ar5523_cmd_tx_cb()
might touch the freed structure.
This patch fixes this issue by canceling in-flight tx cmd if submitted
urb timed out. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: visconti: Fix memory leak in visconti_register_pll()
@pll->rate_table has allocated memory by kmemdup(), if clk_hw_register()
fails, it should be freed, otherwise it will cause memory leak issue,
this patch fixes it. |
| In the Linux kernel, the following vulnerability has been resolved:
devlink: hold region lock when flushing snapshots
Netdevsim triggers a splat on reload, when it destroys regions
with snapshots pending:
WARNING: CPU: 1 PID: 787 at net/core/devlink.c:6291 devlink_region_snapshot_del+0x12e/0x140
CPU: 1 PID: 787 Comm: devlink Not tainted 6.1.0-07460-g7ae9888d6e1c #580
RIP: 0010:devlink_region_snapshot_del+0x12e/0x140
Call Trace:
<TASK>
devl_region_destroy+0x70/0x140
nsim_dev_reload_down+0x2f/0x60 [netdevsim]
devlink_reload+0x1f7/0x360
devlink_nl_cmd_reload+0x6ce/0x860
genl_family_rcv_msg_doit.isra.0+0x145/0x1c0
This is the locking assert in devlink_region_snapshot_del(),
we're supposed to be holding the region->snapshot_lock here. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: avoid uninit memory read in ath9k_htc_rx_msg()
syzbot is reporting uninit value at ath9k_htc_rx_msg() [1], for
ioctl(USB_RAW_IOCTL_EP_WRITE) can call ath9k_hif_usb_rx_stream() with
pkt_len = 0 but ath9k_hif_usb_rx_stream() uses
__dev_alloc_skb(pkt_len + 32, GFP_ATOMIC) based on an assumption that
pkt_len is valid. As a result, ath9k_hif_usb_rx_stream() allocates skb
with uninitialized memory and ath9k_htc_rx_msg() is reading from
uninitialized memory.
Since bytes accessed by ath9k_htc_rx_msg() is not known until
ath9k_htc_rx_msg() is called, it would be difficult to check minimal valid
pkt_len at "if (pkt_len > 2 * MAX_RX_BUF_SIZE) {" line in
ath9k_hif_usb_rx_stream().
We have two choices. One is to workaround by adding __GFP_ZERO so that
ath9k_htc_rx_msg() sees 0 if pkt_len is invalid. The other is to let
ath9k_htc_rx_msg() validate pkt_len before accessing. This patch chose
the latter.
Note that I'm not sure threshold condition is correct, for I can't find
details on possible packet length used by this protocol. |
| In the Linux kernel, the following vulnerability has been resolved:
HSI: ssi_protocol: fix potential resource leak in ssip_pn_open()
ssip_pn_open() claims the HSI client's port with hsi_claim_port(). When
hsi_register_port_event() gets some error and returns a negetive value,
the HSI client's port should be released with hsi_release_port().
Fix it by calling hsi_release_port() when hsi_register_port_event() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio-crypto: fix memory leak in virtio_crypto_alg_skcipher_close_session()
'vc_ctrl_req' is alloced in virtio_crypto_alg_skcipher_close_session(),
and should be freed in the invalid ctrl_status->status error handling
case. Otherwise there is a memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
vdpa_sim: fix possible memory leak in vdpasim_net_init() and vdpasim_blk_init()
Inject fault while probing module, if device_register() fails in
vdpasim_net_init() or vdpasim_blk_init(), but the refcount of kobject is
not decreased to 0, the name allocated in dev_set_name() is leaked.
Fix this by calling put_device(), so that name can be freed in
callback function kobject_cleanup().
(vdpa_sim_net)
unreferenced object 0xffff88807eebc370 (size 16):
comm "modprobe", pid 3848, jiffies 4362982860 (age 18.153s)
hex dump (first 16 bytes):
76 64 70 61 73 69 6d 5f 6e 65 74 00 6b 6b 6b a5 vdpasim_net.kkk.
backtrace:
[<ffffffff8174f19e>] __kmalloc_node_track_caller+0x4e/0x150
[<ffffffff81731d53>] kstrdup+0x33/0x60
[<ffffffff83a5d421>] kobject_set_name_vargs+0x41/0x110
[<ffffffff82d87aab>] dev_set_name+0xab/0xe0
[<ffffffff82d91a23>] device_add+0xe3/0x1a80
[<ffffffffa0270013>] 0xffffffffa0270013
[<ffffffff81001c27>] do_one_initcall+0x87/0x2e0
[<ffffffff813739cb>] do_init_module+0x1ab/0x640
[<ffffffff81379d20>] load_module+0x5d00/0x77f0
[<ffffffff8137bc40>] __do_sys_finit_module+0x110/0x1b0
[<ffffffff83c4d505>] do_syscall_64+0x35/0x80
[<ffffffff83e0006a>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
(vdpa_sim_blk)
unreferenced object 0xffff8881070c1250 (size 16):
comm "modprobe", pid 6844, jiffies 4364069319 (age 17.572s)
hex dump (first 16 bytes):
76 64 70 61 73 69 6d 5f 62 6c 6b 00 6b 6b 6b a5 vdpasim_blk.kkk.
backtrace:
[<ffffffff8174f19e>] __kmalloc_node_track_caller+0x4e/0x150
[<ffffffff81731d53>] kstrdup+0x33/0x60
[<ffffffff83a5d421>] kobject_set_name_vargs+0x41/0x110
[<ffffffff82d87aab>] dev_set_name+0xab/0xe0
[<ffffffff82d91a23>] device_add+0xe3/0x1a80
[<ffffffffa0220013>] 0xffffffffa0220013
[<ffffffff81001c27>] do_one_initcall+0x87/0x2e0
[<ffffffff813739cb>] do_init_module+0x1ab/0x640
[<ffffffff81379d20>] load_module+0x5d00/0x77f0
[<ffffffff8137bc40>] __do_sys_finit_module+0x110/0x1b0
[<ffffffff83c4d505>] do_syscall_64+0x35/0x80
[<ffffffff83e0006a>] entry_SYSCALL_64_after_hwframe+0x46/0xb0 |
| In the Linux kernel, the following vulnerability has been resolved:
USB: gadget: Fix use-after-free during usb config switch
In the process of switching USB config from rndis to other config,
if the hardware does not support the ->pullup callback, or the
hardware encounters a low probability fault, both of them may cause
the ->pullup callback to fail, which will then cause a system panic
(use after free).
The gadget drivers sometimes need to be unloaded regardless of the
hardware's behavior.
Analysis as follows:
=======================================================================
(1) write /config/usb_gadget/g1/UDC "none"
gether_disconnect+0x2c/0x1f8
rndis_disable+0x4c/0x74
composite_disconnect+0x74/0xb0
configfs_composite_disconnect+0x60/0x7c
usb_gadget_disconnect+0x70/0x124
usb_gadget_unregister_driver+0xc8/0x1d8
gadget_dev_desc_UDC_store+0xec/0x1e4
(2) rm /config/usb_gadget/g1/configs/b.1/f1
rndis_deregister+0x28/0x54
rndis_free+0x44/0x7c
usb_put_function+0x14/0x1c
config_usb_cfg_unlink+0xc4/0xe0
configfs_unlink+0x124/0x1c8
vfs_unlink+0x114/0x1dc
(3) rmdir /config/usb_gadget/g1/functions/rndis.gs4
panic+0x1fc/0x3d0
do_page_fault+0xa8/0x46c
do_mem_abort+0x3c/0xac
el1_sync_handler+0x40/0x78
0xffffff801138f880
rndis_close+0x28/0x34
eth_stop+0x74/0x110
dev_close_many+0x48/0x194
rollback_registered_many+0x118/0x814
unregister_netdev+0x20/0x30
gether_cleanup+0x1c/0x38
rndis_attr_release+0xc/0x14
kref_put+0x74/0xb8
configfs_rmdir+0x314/0x374
If gadget->ops->pullup() return an error, function rndis_close() will be
called, then it will causes a use-after-free problem.
======================================================================= |
| In the Linux kernel, the following vulnerability has been resolved:
serial: qcom-geni: Fix blocked task
Revert commit 1afa70632c39 ("serial: qcom-geni: Enable PM runtime for
serial driver") and its dependent commit 86fa39dd6fb7 ("serial:
qcom-geni: Enable Serial on SA8255p Qualcomm platforms") because the
first one causes regression - hang task on Qualcomm RB1 board (QRB2210)
and unable to use serial at all during normal boot:
INFO: task kworker/u16:0:12 blocked for more than 42 seconds.
Not tainted 6.17.0-rc1-00004-g53e760d89498 #9
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u16:0 state:D stack:0 pid:12 tgid:12 ppid:2 task_flags:0x4208060 flags:0x00000010
Workqueue: async async_run_entry_fn
Call trace:
__switch_to+0xe8/0x1a0 (T)
__schedule+0x290/0x7c0
schedule+0x34/0x118
rpm_resume+0x14c/0x66c
rpm_resume+0x2a4/0x66c
rpm_resume+0x2a4/0x66c
rpm_resume+0x2a4/0x66c
__pm_runtime_resume+0x50/0x9c
__driver_probe_device+0x58/0x120
driver_probe_device+0x3c/0x154
__driver_attach_async_helper+0x4c/0xc0
async_run_entry_fn+0x34/0xe0
process_one_work+0x148/0x290
worker_thread+0x2c4/0x3e0
kthread+0x118/0x1c0
ret_from_fork+0x10/0x20
The issue was reported on 12th of August and was ignored by author of
commits introducing issue for two weeks. Only after complaining author
produced a fix which did not work, so if original commits cannot be
reliably fixed for 5 weeks, they obviously are buggy and need to be
dropped. |
| In the Linux kernel, the following vulnerability has been resolved:
net: core: prevent NULL deref in generic_hwtstamp_ioctl_lower()
The ethtool tsconfig Netlink path can trigger a null pointer
dereference. A call chain such as:
tsconfig_prepare_data() ->
dev_get_hwtstamp_phylib() ->
vlan_hwtstamp_get() ->
generic_hwtstamp_get_lower() ->
generic_hwtstamp_ioctl_lower()
results in generic_hwtstamp_ioctl_lower() being called with
kernel_cfg->ifr as NULL.
The generic_hwtstamp_ioctl_lower() function does not expect
a NULL ifr and dereferences it, leading to a system crash.
Fix this by adding a NULL check for kernel_cfg->ifr in
generic_hwtstamp_ioctl_lower(). If ifr is NULL, return -EINVAL. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: micrel: always set shared->phydev for LAN8814
Currently, during the LAN8814 PTP probe shared->phydev is only set if PTP
clock gets actually set, otherwise the function will return before setting
it.
This is an issue as shared->phydev is unconditionally being used when IRQ
is being handled, especially in lan8814_gpio_process_cap and since it was
not set it will cause a NULL pointer exception and crash the kernel.
So, simply always set shared->phydev to avoid the NULL pointer exception. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: directly free partially initialized fs_info in btrfs_check_leaked_roots()
If fs_info->super_copy or fs_info->super_for_commit allocated failed in
btrfs_get_tree_subvol(), then no need to call btrfs_free_fs_info().
Otherwise btrfs_check_leaked_roots() would access NULL pointer because
fs_info->allocated_roots had not been initialised.
syzkaller reported the following information:
------------[ cut here ]------------
BUG: unable to handle page fault for address: fffffffffffffbb0
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 64c9067 P4D 64c9067 PUD 64cb067 PMD 0
Oops: Oops: 0000 [#1] SMP KASAN PTI
CPU: 0 UID: 0 PID: 1402 Comm: syz.1.35 Not tainted 6.15.8 #4 PREEMPT(lazy)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), (...)
RIP: 0010:arch_atomic_read arch/x86/include/asm/atomic.h:23 [inline]
RIP: 0010:raw_atomic_read include/linux/atomic/atomic-arch-fallback.h:457 [inline]
RIP: 0010:atomic_read include/linux/atomic/atomic-instrumented.h:33 [inline]
RIP: 0010:refcount_read include/linux/refcount.h:170 [inline]
RIP: 0010:btrfs_check_leaked_roots+0x18f/0x2c0 fs/btrfs/disk-io.c:1230
[...]
Call Trace:
<TASK>
btrfs_free_fs_info+0x310/0x410 fs/btrfs/disk-io.c:1280
btrfs_get_tree_subvol+0x592/0x6b0 fs/btrfs/super.c:2029
btrfs_get_tree+0x63/0x80 fs/btrfs/super.c:2097
vfs_get_tree+0x98/0x320 fs/super.c:1759
do_new_mount+0x357/0x660 fs/namespace.c:3899
path_mount+0x716/0x19c0 fs/namespace.c:4226
do_mount fs/namespace.c:4239 [inline]
__do_sys_mount fs/namespace.c:4450 [inline]
__se_sys_mount fs/namespace.c:4427 [inline]
__x64_sys_mount+0x28c/0x310 fs/namespace.c:4427
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x92/0x180 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f032eaffa8d
[...] |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: also call xfrm_state_delete_tunnel at destroy time for states that were never added
In commit b441cf3f8c4b ("xfrm: delete x->tunnel as we delete x"), I
missed the case where state creation fails between full
initialization (->init_state has been called) and being inserted on
the lists.
In this situation, ->init_state has been called, so for IPcomp
tunnels, the fallback tunnel has been created and added onto the
lists, but the user state never gets added, because we fail before
that. The user state doesn't go through __xfrm_state_delete, so we
don't call xfrm_state_delete_tunnel for those states, and we end up
leaking the FB tunnel.
There are several codepaths affected by this: the add/update paths, in
both net/key and xfrm, and the migrate code (xfrm_migrate,
xfrm_state_migrate). A "proper" rollback of the init_state work would
probably be doable in the add/update code, but for migrate it gets
more complicated as multiple states may be involved.
At some point, the new (not-inserted) state will be destroyed, so call
xfrm_state_delete_tunnel during xfrm_state_gc_destroy. Most states
will have their fallback tunnel cleaned up during __xfrm_state_delete,
which solves the issue that b441cf3f8c4b (and other patches before it)
aimed at. All states (including FB tunnels) will be removed from the
lists once xfrm_state_fini has called flush_work(&xfrm_state_gc_work). |
| In the Linux kernel, the following vulnerability has been resolved:
s390/fpu: Fix false-positive kmsan report in fpu_vstl()
A false-positive kmsan report is detected when running ping command.
An inline assembly instruction 'vstl' can write varied amount of bytes
depending on value of 'index' argument. If 'index' > 0, 'vstl' writes
at least 2 bytes.
clang generates kmsan write helper call depending on inline assembly
constraints. Constraints are evaluated compile-time, but value of
'index' argument is known only at runtime.
clang currently generates call to __msan_instrument_asm_store with 1 byte
as size. Manually call kmsan function to indicate correct amount of bytes
written and fix false-positive report.
This change fixes following kmsan reports:
[ 36.563119] =====================================================
[ 36.563594] BUG: KMSAN: uninit-value in virtqueue_add+0x35c6/0x7c70
[ 36.563852] virtqueue_add+0x35c6/0x7c70
[ 36.564016] virtqueue_add_outbuf+0xa0/0xb0
[ 36.564266] start_xmit+0x288c/0x4a20
[ 36.564460] dev_hard_start_xmit+0x302/0x900
[ 36.564649] sch_direct_xmit+0x340/0xea0
[ 36.564894] __dev_queue_xmit+0x2e94/0x59b0
[ 36.565058] neigh_resolve_output+0x936/0xb40
[ 36.565278] __neigh_update+0x2f66/0x3a60
[ 36.565499] neigh_update+0x52/0x60
[ 36.565683] arp_process+0x1588/0x2de0
[ 36.565916] NF_HOOK+0x1da/0x240
[ 36.566087] arp_rcv+0x3e4/0x6e0
[ 36.566306] __netif_receive_skb_list_core+0x1374/0x15a0
[ 36.566527] netif_receive_skb_list_internal+0x1116/0x17d0
[ 36.566710] napi_complete_done+0x376/0x740
[ 36.566918] virtnet_poll+0x1bae/0x2910
[ 36.567130] __napi_poll+0xf4/0x830
[ 36.567294] net_rx_action+0x97c/0x1ed0
[ 36.567556] handle_softirqs+0x306/0xe10
[ 36.567731] irq_exit_rcu+0x14c/0x2e0
[ 36.567910] do_io_irq+0xd4/0x120
[ 36.568139] io_int_handler+0xc2/0xe8
[ 36.568299] arch_cpu_idle+0xb0/0xc0
[ 36.568540] arch_cpu_idle+0x76/0xc0
[ 36.568726] default_idle_call+0x40/0x70
[ 36.568953] do_idle+0x1d6/0x390
[ 36.569486] cpu_startup_entry+0x9a/0xb0
[ 36.569745] rest_init+0x1ea/0x290
[ 36.570029] start_kernel+0x95e/0xb90
[ 36.570348] startup_continue+0x2e/0x40
[ 36.570703]
[ 36.570798] Uninit was created at:
[ 36.571002] kmem_cache_alloc_node_noprof+0x9e8/0x10e0
[ 36.571261] kmalloc_reserve+0x12a/0x470
[ 36.571553] __alloc_skb+0x310/0x860
[ 36.571844] __ip_append_data+0x483e/0x6a30
[ 36.572170] ip_append_data+0x11c/0x1e0
[ 36.572477] raw_sendmsg+0x1c8c/0x2180
[ 36.572818] inet_sendmsg+0xe6/0x190
[ 36.573142] __sys_sendto+0x55e/0x8e0
[ 36.573392] __s390x_sys_socketcall+0x19ae/0x2ba0
[ 36.573571] __do_syscall+0x12e/0x240
[ 36.573823] system_call+0x6e/0x90
[ 36.573976]
[ 36.574017] Byte 35 of 98 is uninitialized
[ 36.574082] Memory access of size 98 starts at 0000000007aa0012
[ 36.574218]
[ 36.574325] CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Tainted: G B N 6.17.0-dirty #16 NONE
[ 36.574541] Tainted: [B]=BAD_PAGE, [N]=TEST
[ 36.574617] Hardware name: IBM 3931 A01 703 (KVM/Linux)
[ 36.574755] =====================================================
[ 63.532541] =====================================================
[ 63.533639] BUG: KMSAN: uninit-value in virtqueue_add+0x35c6/0x7c70
[ 63.533989] virtqueue_add+0x35c6/0x7c70
[ 63.534940] virtqueue_add_outbuf+0xa0/0xb0
[ 63.535861] start_xmit+0x288c/0x4a20
[ 63.536708] dev_hard_start_xmit+0x302/0x900
[ 63.537020] sch_direct_xmit+0x340/0xea0
[ 63.537997] __dev_queue_xmit+0x2e94/0x59b0
[ 63.538819] neigh_resolve_output+0x936/0xb40
[ 63.539793] ip_finish_output2+0x1ee2/0x2200
[ 63.540784] __ip_finish_output+0x272/0x7a0
[ 63.541765] ip_finish_output+0x4e/0x5e0
[ 63.542791] ip_output+0x166/0x410
[ 63.543771] ip_push_pending_frames+0x1a2/0x470
[ 63.544753] raw_sendmsg+0x1f06/0x2180
[ 63.545033] inet_sendmsg+0xe6/0x190
[ 63.546006] __sys_sendto+0x55e/0x8e0
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: at91-sama5d2_adc: Fix potential use-after-free in sama5d2_adc driver
at91_adc_interrupt can call at91_adc_touch_data_handler function
to start the work by schedule_work(&st->touch_st.workq).
If we remove the module which will call at91_adc_remove to
make cleanup, it will free indio_dev through iio_device_unregister but
quite a bit later. While the work mentioned above will be used. The
sequence of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| at91_adc_workq_handler
at91_adc_remove |
iio_device_unregister(indio_dev) |
//free indio_dev a bit later |
| iio_push_to_buffers(indio_dev)
| //use indio_dev
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in at91_adc_remove. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: sh-sci: fix RSCI FIFO overrun handling
The receive error handling code is shared between RSCI and all other
SCIF port types, but the RSCI overrun_reg is specified as a memory
offset, while for other SCIF types it is an enum value used to index
into the sci_port_params->regs array, as mentioned above the
sci_serial_in() function.
For RSCI, the overrun_reg is CSR (0x48), causing the sci_getreg() call
inside the sci_handle_fifo_overrun() function to index outside the
bounds of the regs array, which currently has a size of 20, as specified
by SCI_NR_REGS.
Because of this, we end up accessing memory outside of RSCI's
rsci_port_params structure, which, when interpreted as a plat_sci_reg,
happens to have a non-zero size, causing the following WARN when
sci_serial_in() is called, as the accidental size does not match the
supported register sizes.
The existence of the overrun_reg needs to be checked because
SCIx_SH3_SCIF_REGTYPE has overrun_reg set to SCLSR, but SCLSR is not
present in the regs array.
Avoid calling sci_getreg() for port types which don't use standard
register handling.
Use the ops->read_reg() and ops->write_reg() functions to properly read
and write registers for RSCI, and change the type of the status variable
to accommodate the 32-bit CSR register.
sci_getreg() and sci_serial_in() are also called with overrun_reg in the
sci_mpxed_interrupt() interrupt handler, but that code path is not used
for RSCI, as it does not have a muxed interrupt.
------------[ cut here ]------------
Invalid register access
WARNING: CPU: 0 PID: 0 at drivers/tty/serial/sh-sci.c:522 sci_serial_in+0x38/0xac
Modules linked in: renesas_usbhs at24 rzt2h_adc industrialio_adc sha256 cfg80211 bluetooth ecdh_generic ecc rfkill fuse drm backlight ipv6
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.17.0-rc1+ #30 PREEMPT
Hardware name: Renesas RZ/T2H EVK Board based on r9a09g077m44 (DT)
pstate: 604000c5 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : sci_serial_in+0x38/0xac
lr : sci_serial_in+0x38/0xac
sp : ffff800080003e80
x29: ffff800080003e80 x28: ffff800082195b80 x27: 000000000000000d
x26: ffff8000821956d0 x25: 0000000000000000 x24: ffff800082195b80
x23: ffff000180e0d800 x22: 0000000000000010 x21: 0000000000000000
x20: 0000000000000010 x19: ffff000180e72000 x18: 000000000000000a
x17: ffff8002bcee7000 x16: ffff800080000000 x15: 0720072007200720
x14: 0720072007200720 x13: 0720072007200720 x12: 0720072007200720
x11: 0000000000000058 x10: 0000000000000018 x9 : ffff8000821a6a48
x8 : 0000000000057fa8 x7 : 0000000000000406 x6 : ffff8000821fea48
x5 : ffff00033ef88408 x4 : ffff8002bcee7000 x3 : ffff800082195b80
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff800082195b80
Call trace:
sci_serial_in+0x38/0xac (P)
sci_handle_fifo_overrun.isra.0+0x70/0x134
sci_er_interrupt+0x50/0x39c
__handle_irq_event_percpu+0x48/0x140
handle_irq_event+0x44/0xb0
handle_fasteoi_irq+0xf4/0x1a0
handle_irq_desc+0x34/0x58
generic_handle_domain_irq+0x1c/0x28
gic_handle_irq+0x4c/0x140
call_on_irq_stack+0x30/0x48
do_interrupt_handler+0x80/0x84
el1_interrupt+0x34/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
default_idle_call+0x28/0x58 (P)
do_idle+0x1f8/0x250
cpu_startup_entry+0x34/0x3c
rest_init+0xd8/0xe0
console_on_rootfs+0x0/0x6c
__primary_switched+0x88/0x90
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
media: imon: make send_packet() more robust
syzbot is reporting that imon has three problems which result in
hung tasks due to forever holding device lock [1].
First problem is that when usb_rx_callback_intf0() once got -EPROTO error
after ictx->dev_present_intf0 became true, usb_rx_callback_intf0()
resubmits urb after printk(), and resubmitted urb causes
usb_rx_callback_intf0() to again get -EPROTO error. This results in
printk() flooding (RCU stalls).
Alan Stern commented [2] that
In theory it's okay to resubmit _if_ the driver has a robust
error-recovery scheme (such as giving up after some fixed limit on the
number of errors or after some fixed time has elapsed, perhaps with a
time delay to prevent a flood of errors). Most drivers don't bother to
do this; they simply give up right away. This makes them more
vulnerable to short-term noise interference during USB transfers, but in
reality such interference is quite rare. There's nothing really wrong
with giving up right away.
but imon has a poor error-recovery scheme which just retries forever;
this behavior should be fixed.
Since I'm not sure whether it is safe for imon users to give up upon any
error code, this patch takes care of only union of error codes chosen from
modules in drivers/media/rc/ directory which handle -EPROTO error (i.e.
ir_toy, mceusb and igorplugusb).
Second problem is that when usb_rx_callback_intf0() once got -EPROTO error
before ictx->dev_present_intf0 becomes true, usb_rx_callback_intf0() always
resubmits urb due to commit 8791d63af0cf ("[media] imon: don't wedge
hardware after early callbacks"). Move the ictx->dev_present_intf0 test
introduced by commit 6f6b90c9231a ("[media] imon: don't parse scancodes
until intf configured") to immediately before imon_incoming_packet(), or
the first problem explained above happens without printk() flooding (i.e.
hung task).
Third problem is that when usb_rx_callback_intf0() is not called for some
reason (e.g. flaky hardware; the reproducer for this problem sometimes
prevents usb_rx_callback_intf0() from being called),
wait_for_completion_interruptible() in send_packet() never returns (i.e.
hung task). As a workaround for such situation, change send_packet() to
wait for completion with timeout of 10 seconds. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: x86: s2idle: Catch multiple ACPI_TYPE_PACKAGE objects
If a badly constructed firmware includes multiple `ACPI_TYPE_PACKAGE`
objects while evaluating the AMD LPS0 _DSM, there will be a memory
leak. Explicitly guard against this. |
