| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
irqchip/irq-riscv-imsic-early: Fix fwnode leak on state setup failure
imsic_early_acpi_init() allocates a firmware node before setting up the
IMSIC state. If imsic_setup_state() fails, the function returns without
freeing the allocated fwnode.
Free the fwnode and clear the global pointer on this error path, matching
the cleanup already done when imsic_early_probe() fails.
[ tglx: Use a common cleanup path instead of copying code around ] |
| In the Linux kernel, the following vulnerability has been resolved:
net: macb: drop in-flight Tx SKBs on close
The MACB driver has since forever leaked the outgoing SKBs that
have not yet been marked as completed. They live in queue->tx_skb
which gets freed without remorse nor checking.
macb_free_consistent() gets called in a few codepaths, but only close will
trigger the added expressions. In macb_open() and macb_alloc_consistent()
failure cases, queues' tx_skb just got allocated and are empty. |
| In the Linux kernel, the following vulnerability has been resolved:
drbd: reject data replies with an out-of-range payload size
recv_dless_read() receives a P_DATA_REPLY from a peer into the bio of an
outstanding read request. The peer-supplied payload length reaches it as
the signed int data_size, and two peer-controlled inputs can make it
negative. With a negotiated data-integrity-alg the digest length is
subtracted first, so a reply whose payload is smaller than the digest
underflows data_size. With no integrity algorithm (the default) data_size
is assigned from the unsigned h95/h100 wire length and drbdd() never
bounds it for a payload-carrying command, so a length above INT_MAX casts
it negative; this path needs no non-default feature. The bio receive loop
then computes expect = min_t(int, data_size, bv_len), which is negative,
and drbd_recv_all_warn(mapped, expect) receives with a size_t of SIZE_MAX
into the first mapped page.
The sibling receive path read_in_block() is not affected: it uses an
unsigned size and rejects it against DRBD_MAX_BIO_SIZE before receiving.
Reject a data reply whose size is negative after the optional digest
subtraction, covering both triggers.
Impact: a malicious or man-in-the-middle DRBD peer copies attacker-chosen
bytes past a bio page in the receiver, corrupting kernel memory. A node
that reads from its peer (a diskless node, or read-balancing to the peer)
is exposed in the default configuration; data-integrity-alg is not
required. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: free mlx5_st_idx_data on final dealloc
Workloads that repeatedly allocate and release mkeys carrying TPH
steering-tag hints (e.g. churning RDMA MRs) leak one
struct mlx5_st_idx_data per cycle; kmemleak flags it as unreferenced
and the kmalloc slab grows over time.
When the last reference to an ST table entry is dropped,
mlx5_st_dealloc_index() removed the entry from idx_xa but the backing
mlx5_st_idx_data allocation was never freed.
Free idx_data after the xa_erase() so the lifetime of the bookkeeping
struct matches the lifetime of the ST entry it tracks. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/uaccess: correct check for CONFIG_PPC_E500 in mask_user_address()
mask_user_address() incorrectly checks for CONFIG_E500 instead of
CONFIG_PPC_E500, causing mask_user_address_isel() to not be used on
E500 hardware. Fix the check to use the correct name. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mwifiex: fix permanently busy scans after multiple roam iterations
In order for the firmware to sleep, the driver has to confirm a
previously received sleep request. The normal sequence of evets goes
like this:
EVENT_SLEEP -> adapter->ps_state = PS_STATE_PRE_SLEEP -> sleep-confirm
-> SLEEP -> EVENT_AWAKE -> AWAKE.
Before sending the sleep-confirm command, the driver must make sure
there are no commands either running or waiting to be completed.
mwifiex_ret_802_11_associate() unconditionally sets
ps_state = PS_STATE_AWAKE when it processes the association command
response, outside of the normal powersave management flow. If
EVENT_SLEEP arrives while the association command is in flight,
ps_state is PRE_SLEEP when the association command response is parsed,
and the forced AWAKE overwrites it. The deferred sleep-confirm is
never sent.
A subsequent scan_start command is correctly acknowledged, but the
firmware doesn't generate scan_result events. The scan request never
finishes, and additional requests from userspace fail with -EBUSY.
After testing on both IW412 and W8997, I could only trigger the bug on
the IW412 and observed the firmwares behave differently. On the IW412
the firmware still sends EVENT_SLEEP while the authentication /
association process is ongoing. A W8997 under the same
conditions seems to suppress power-save for the duration of the
association, so PRE_SLEEP never coincided with the association response
even after extended periods of testing using the loops
described below (>12hours).
On the IW412, the delay between commands that triggers an EVENT_SLEEP
was empirically determined to be ~20ms. This delay can naturally occur
when the driver is outputting debugging information
(debug_mask = 0x00000037), in which situation the busy scans issue is
repeatable while running "test 1)" as described below. If the delay
between commands is less than ~20ms, the firmware stays awake and
the issue was not reproducible running the same test.
The host_mlme=false path also behaves differently. In this case, the
entire authentication / association transaction is executed by one
command (HostCmd_CMD_802_11_ASSOCIATE), and the firmware doesn't emit
EVENT_SLEEP while the command is running.
Remove the assignment so the ps_state is only manipulated in the paths
that are related to powersave event handling and on the main workqueue
for correct sleep confirmation.
The following loop tests were performed (with debugging output enabled):
1) force roaming between two AP's, one 5GHz and one 2.4GHz, same
SSID. Use wpa_cli to trigger the roaming behavior, sleep 2s
between iterations.
2) force a disconnection to AP 1 and a connection to AP 2, test
scan. Use wpa_cli to trigger the connection changes, sleep 2s
between iterations.
Each test ran in each device for at least 3 hours. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: virt-concat: free duplicate generated name
Every MTD registration runs mtd_virt_concat_create_join(). Once a
virtual concat has already been registered, the function builds the same
name again and takes the equal-name branch. That branch skips to the
next item without freeing the newly allocated string.
Free the temporary name before continuing. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: rawnand: lpc32xx_slc: fail DMA transfer on completion timeout
lpc32xx_xmit_dma() waits for the DMA completion callback but ignores
wait_for_completion_timeout(). A timed out DMA transfer is therefore
unmapped and reported as successful to the NAND read/write path.
Return -ETIMEDOUT when the completion wait expires. Terminate the DMA
channel before unmapping the scatterlist so the timed out transfer cannot
continue to access the buffer after the error is returned. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix potential deadlock in f2fs_balance_fs()
When the f2fs filesystem space is nearly exhausted, we encounter deadlock
issues as below:
INFO: task A:1890 blocked for more than 120 seconds.
Tainted: G O 6.12.41-g3fe07ddf05ab #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:A state:D stack:0 pid:1890 tgid:1626 ppid:1153 flags:0x00000204
Call trace:
__switch_to+0xf4/0x158
__schedule+0x27c/0x908
schedule+0x3c/0x118
io_schedule+0x44/0x68
folio_wait_bit_common+0x174/0x370
folio_wait_bit+0x20/0x38
folio_wait_writeback+0x54/0xc8
truncate_inode_partial_folio+0x70/0x1e0
truncate_inode_pages_range+0x1b0/0x450
truncate_pagecache+0x54/0x88
f2fs_file_write_iter+0x3e8/0xb80
do_iter_readv_writev+0xf0/0x1e0
vfs_writev+0x138/0x2c8
do_writev+0x88/0x130
__arm64_sys_writev+0x28/0x40
invoke_syscall+0x50/0x120
el0_svc_common.constprop.0+0xc8/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x30/0xf8
el0t_64_sync_handler+0x120/0x130
el0t_64_sync+0x190/0x198
INFO: task kworker/u8:11:2680853 blocked for more than 120 seconds.
Tainted: G O 6.12.41-g3fe07ddf05ab #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u8:11 state:D stack:0 pid:2680853 tgid:2680853 ppid:2 flags:0x00000208
Workqueue: writeback wb_workfn (flush-254:0)
Call trace:
__switch_to+0xf4/0x158
__schedule+0x27c/0x908
schedule+0x3c/0x118
io_schedule+0x44/0x68
folio_wait_bit_common+0x174/0x370
__filemap_get_folio+0x214/0x348
pagecache_get_page+0x20/0x70
f2fs_get_read_data_page+0x150/0x3e8
f2fs_get_lock_data_page+0x2c/0x160
move_data_page+0x50/0x478
do_garbage_collect+0xd38/0x1528
f2fs_gc+0x240/0x7e0
f2fs_balance_fs+0x1a0/0x208
f2fs_write_single_data_page+0x6e4/0x730
f2fs_write_cache_pages+0x378/0x9b0
f2fs_write_data_pages+0x2e4/0x388
do_writepages+0x8c/0x2c8
__writeback_single_inode+0x4c/0x498
writeback_sb_inodes+0x234/0x4a8
__writeback_inodes_wb+0x58/0x118
wb_writeback+0x2f8/0x3c0
wb_workfn+0x2c4/0x508
process_one_work+0x180/0x408
worker_thread+0x258/0x368
kthread+0x118/0x128
ret_from_fork+0x10/0x200
INFO: task kworker/u8:8:2641297 blocked for more than 120 seconds.
Tainted: G O 6.12.41-g3fe07ddf05ab #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u8:8 state:D stack:0 pid:2641297 tgid:2641297 ppid:2 flags:0x00000208
Workqueue: writeback wb_workfn (flush-254:0)
Call trace:
__switch_to+0xf4/0x158
__schedule+0x27c/0x908
rt_mutex_schedule+0x30/0x60
__rt_mutex_slowlock_locked.constprop.0+0x460/0x8a8
rwbase_write_lock+0x24c/0x378
down_write+0x1c/0x30
f2fs_balance_fs+0x184/0x208
f2fs_write_inode+0xf4/0x328
__writeback_single_inode+0x370/0x498
writeback_sb_inodes+0x234/0x4a8
__writeback_inodes_wb+0x58/0x118
wb_writeback+0x2f8/0x3c0
wb_workfn+0x2c4/0x508
process_one_work+0x180/0x408
worker_thread+0x258/0x368
kthread+0x118/0x128
ret_from_fork+0x10/0x20
INFO: task B:1902 blocked for more than 120 seconds.
Tainted: G O 6.12.41-g3fe07ddf05ab #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:B state:D stack:0 pid:1902 tgid:1626 ppid:1153 flags:0x0000020c
Call trace:
__switch_to+0xf4/0x158
__schedule+0x27c/0x908
rt_mutex_schedule+0x30/0x60
__rt_mutex_slowlock_locked.constprop.0+0x460/0x8a8
rwbase_write_lock+0x24c/0x378
down_write+0x1c/0x30
f2fs_balance_fs+0x184/0x208
f2fs_map_blocks+0x94c/0x1110
f2fs_file_write_iter+0x228/0xb80
do_iter_readv_writev+0xf0/0x1e0
vfs_writev+0x138/0x2c8
do_writev+0x88/0x130
__arm64_sys_writev+0x28/0x40
invoke_syscall+0x50/0x120
el0_svc_common.constprop.0+0xc8/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x30/0xf8
el0t_64_sync_handler+0x120/0x130
el0t_64_sync+0x190/0x198
INFO: task sync:2769849 blocked for more than 120 seconds.
Tainted: G
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix potential deadlock in gc_merge path of f2fs_balance_fs()
When we mount device w/ gc_merge mount option, we may suffer below
potential deadlock:
Kworker GC trehad Truncator
- f2fs_write_cache_pages
- f2fs_write_single_data_page
- f2fs_do_write_data_page
- folio_start_writeback --- set writeback flag on folio
- f2fs_outplace_write_data
: cached folio in internal bio cache
- f2fs_balance_fs
- wake_up(gc_thread)
: wake up gc thread to run foreground GC
- finish_wait(fggc_wq)
: wait on the waitqueue --- wait on GC thread to finish the work
- truncate_inode_pages_range
- __filemap_get_folio(, FGP_LOCK) --- lock folio
- truncate_inode_partial_folio
- folio_wait_writeback --- wait on writeback being cleared
- do_garbage_collect
- move_data_page
- f2fs_get_lock_data_folio
- lock on folio --- blocked on folio's lock
In order to avoid such deadlock, let's call below functions to commit
cached bios in GC_MERGE path of f2fs_balance_fs() as the same as we did
in NOGC_MERGE path.
- f2fs_submit_merged_write(sbi, DATA);
- f2fs_submit_all_merged_ipu_writes(sbi); |
| Inconsistent interpretation of http requests ('http request/response smuggling') in .NET allows an unauthorized attacker to bypass a security feature over a network. |
| Improper removal of sensitive information before storage or transfer in .NET allows an unauthorized attacker to disclose information over a network. |
| Unchecked input for loop condition in .NET allows an unauthorized attacker to deny service over a network. |
| Uncaught exception in .NET allows an authorized attacker to elevate privileges locally. |
| Integer overflow or wraparound in .NET allows an unauthorized attacker to elevate privileges locally. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Fix signed integer truncation in IPC receive
Fix potential buffer overflow where firmware-supplied data_size is cast
to signed int before being used in min_t(). Large unsigned values
(>= 0x80000000) become negative, causing unsigned wraparound and
oversized memcpy operations that can overflow the stack buffer.
Change min_t(int, ...) to min() as both values are unsigned and can be
handled by min() without explicit cast. |
| In the Linux kernel, the following vulnerability has been resolved:
inet: frags: fix use-after-free caused by the fqdir_pre_exit() flush
On netns teardown, fqdir_pre_exit() walks the fqdir rhashtable and
flushes every fragment queue that is not yet complete using
inet_frag_queue_flush(). That helper frees all the skbs queued on the
fragment queue but does not set INET_FRAG_COMPLETE, and leaves
q->fragments_tail and q->last_run_head pointing at the freed skbs.
The queue itself stays in the rhashtable.
fqdir_pre_exit() first lowers high_thresh to 0 to stop new queue lookups,
but it cannot stop a fragment that already obtained the queue through
inet_frag_find() earlier and stalled just before taking the queue lock.
Once that fragment resumes after the flush and takes the queue lock,
it passes the INET_FRAG_COMPLETE check and then dereferences the freed
fragments_tail. inet_frag_queue_insert() reads FRAG_CB() and ->len of
that pointer and, on the append path, writes ->next_frag, causing a
slab use-after-free. IPv6, nf_conntrack_reasm6 and 6lowpan reassembly
share the same flush path and are affected as well.
Reset rb_fragments, fragments_tail and last_run_head in
inet_frag_queue_flush() so a flushed queue no longer points at the
freed skbs. A fragment that resumes after the flush and takes the
queue lock then finds an empty queue and starts a new run instead of
dereferencing the freed fragments_tail. ip_frag_reinit() already
performed this reset after its own flush, so drop the now duplicate
code there. |
| Out-of-bounds write in .NET allows an unauthorized attacker to execute code locally. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: fix two unsafe bare decodes in decode_lockers()
decode_lockers() in cls_lock_client.c contains two bare decode operations
that allow a malicious or compromised OSD to trigger slab-out-of-bounds
reads:
1. ceph_decode_32(p) at the num_lockers field has no preceding bounds
check. ceph_start_decoding() accepts struct_len=0 as valid -- the
internal ceph_decode_need(p, end, 0, bad) always passes -- so when an
OSD sends struct_len=0, ceph_start_decoding() returns success with
p == end. The immediately following bare ceph_decode_32(p) then reads
4 bytes past the validated buffer boundary. The garbage value is
passed directly to kzalloc_objs() as the locker count.
The sibling function decode_watchers() in osd_client.c already uses
ceph_decode_32_safe() after its own ceph_start_decoding() call.
decode_lockers() was the only site using the bare variant.
2. ceph_decode_8(p) after the decode_locker() loop has no preceding
bounds check. If an OSD crafts num_lockers such that the loop
advances p exactly to end, the subsequent bare ceph_decode_8(p) reads
one byte past the validated buffer boundary. The result is passed
directly into *type, which is used as a lock type discriminator by
callers, giving an OSD-controlled one-byte OOB read with direct
influence over the lock type field.
Fix both by replacing bare operations with their safe variants:
ceph_decode_32(p) -> ceph_decode_32_safe(p, end, *num_lockers,
err_inval)
ceph_decode_8(p) -> ceph_decode_8_safe(p, end, *type,
err_free_lockers)
The goto targets differ intentionally:
err_inval: is a new label returning -EINVAL directly. It is used for
the pre-allocation failure path where *lockers is not yet allocated
and must not be passed to ceph_free_lockers().
err_free_lockers: is the existing label. It is used for the
post-allocation failure path where *lockers is allocated and must
be freed.
ret is set to -EINVAL before ceph_decode_8_safe() so that
err_free_lockers returns the correct error code on bounds violation.
Without this, err_free_lockers would return a stale ret value (0 from
the successful decode_locker() loop), silently swallowing the error.
-EINVAL is correct for both failure paths. The data received from the
OSD is structurally malformed. -ENOMEM would misrepresent the failure
class to callers and to stable@ backporters triaging error paths.
Attacker model: a malicious or compromised OSD in a multi-tenant Ceph
deployment can trigger this against any kernel client that issues the
lock.get_info class method (e.g. during RBD exclusive lock acquisition).
[ idryomov: trim changelog, formatting ] |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate ACE size against SID sub-authorities
set_ntacl_dacl() validates sid.num_subauth before copying an ACE, but
does not verify that the declared ACE size contains all sub-authorities
described by that field. An undersized ACE can therefore be copied
and later make the POSIX ACL deduplication walk inspect data beyond
the copied ACE boundary.
The existing initial bound check is also too small. It only ensures
that the ACE size field is accessible before set_ntacl_dacl() reads
sid.num_subauth farther into the input buffer.
Require enough input for the fixed SID header before accessing
num_subauth, reject ACEs smaller than that header, and skip ACEs
whose declared size cannot contain the complete SID. This makes the
validation consistent with the other ACE walk paths. |
