| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
smb/client: fix out-of-bounds read in symlink_data()
Since smb2_check_message() returns success without length validation for
the symlink error response, in symlink_data() it is possible for
iov->iov_len to be smaller than sizeof(struct smb2_err_rsp). If the buffer
only contains the base SMB2 header (64 bytes), accessing
err->ErrorContextCount (at offset 66) or err->ByteCount later in
symlink_data() will cause an out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
sound: ua101: fix division by zero at probe
Add a missing sanity check for bNrChannels in detect_usb_format()
to prevent a division by zero in playback_urb_complete() and
capture_urb_complete().
USB core does not validate class-specific descriptor fields such
as bNrChannels, so drivers must verify them before use. If a
device provides bNrChannels = 0, frame_bytes becomes zero and is
later used as a divisor in the URB completion handlers, leading
to a kernel crash. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/sysfs-schemes: protect path kfree() with damon_sysfs_lock
damon_sysfs_quot_goal->path can be read and written by users, via DAMON
sysfs 'path' file. It can also be indirectly read, for the parameters
{on,off}line committing to DAMON. The reads for parameters committing are
protected by damon_sysfs_lock to avoid the sysfs files being destroyed
while any of the parameters are being read. But the user-driven direct
reads and writes are not protected by any lock, while the write is
deallocating the path-pointing buffer. As a result, the readers could
read the already freed buffer (user-after-free). Note that the user-reads
don't race when the same open file is used by the writer, due to kernfs's
open file locking. Nonetheless, doing the reads and writes with separate
open files would be common. Fix it by protecting both the user-direct
reads and writes with damon_sysfs_lock. |
| In the Linux kernel, the following vulnerability has been resolved:
pseries/papr-hvpipe: Prevent kernel stack memory leak to userspace
The hdr variable is allocated on the stack and only hdr.version and
hdr.flags are initialized explicitly. Because the struct papr_hvpipe_hdr
contains reserved padding bytes (reserved[3] and reserved2[40]), these
could leak the uninitialized bytes to userspace after copy_to_user().
This patch fixes that by initializing the whole struct to 0. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx4: Fix mis-use of RCU in mlx4_srq_event()
Sashiko points out the radix_tree itself is RCU safe, but nothing ever
frees the mlx4_srq struct with RCU, and it isn't even accessed within the
RCU critical section. It also will crash if an event is delivered before
the srq object is finished initializing.
Use the spinlock since it isn't easy to make RCU work, use
refcount_inc_not_zero() to protect against partially initialized objects,
and order the refcount_set() to be after the srq is fully initialized. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: Fix potential use-after-free issue when stopping watchdog task
Watchdog task might end between send_sig() and kthread_stop() calls, what
results in the use-after-free issue. Fix this by increasing watchdog task
reference count before calling send_sig() and dropping it by switching to
kthread_stop_put(). |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SOF: Don't allow pointer operations on unconfigured streams
When reporting the pointer for a compressed stream we report the current
I/O frame position by dividing the position by the number of channels
multiplied by the number of container bytes. These values default to 0 and
are only configured as part of setting the stream parameters so this allows
a divide by zero to be configured. Validate that they are non zero,
returning an error if not |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx4: Fix resource leak on error in mlx4_ib_create_srq()
Sashiko points out that mlx4_srq_alloc() was not undone during error
unwind, add the missing call to mlx4_srq_free(). |
| In the Linux kernel, the following vulnerability has been resolved:
ipmi: Add limits to event and receive message requests
The driver would just fetch events and receive messages until the
BMC said it was done. To avoid issues with BMCs that never say they are
done, add a limit of 10 fetches at a time.
In addition, an si interface has an attn state it can return from the
hardware which is supposed to cause a flag fetch to see if the driver
needs to fetch events or message or a few other things. If the attn
bit gets stuck, it's a similar problem. So allow messages in between
flag fetches so the driver itself doesn't get stuck.
This is a more general fix than the previous fix for the specific bad
BMC, but should fix the more general issue of a BMC that won't stop
saying it has data.
This has been there from the beginning of the driver. It's not a bug
per-se, but it is accounting for bugs in BMCs. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix error path fall-through in mlx5_ib_dev_res_srq_init()
mlx5_ib_dev_res_srq_init() allocates two SRQs, s0 and s1. When
ib_create_srq() fails for s1, the error branch destroys s0 but falls
through and unconditionally assigns the freed s0 and the ERR_PTR s1 to
devr->s0 and devr->s1.
This leads to several problems: the lock-free fast path checks
"if (devr->s1) return 0;" and treats the ERR_PTR as already initialised;
users in mlx5_ib_create_qp() dereference the freed SRQ or ERR_PTR via
to_msrq(devr->s0)->msrq.srqn; and mlx5_ib_dev_res_cleanup() dereferences
the ERR_PTR and double-frees s0 on teardown.
Fix by adding the same `goto unlock` in the s1 failure path. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix fsck inconsistency caused by FGGC of node block
During FGGC node block migration, fsck may incorrectly treat the
migrated node block as fsync-written data.
The reproduction scenario:
root@vm:/mnt/f2fs# seq 1 2048 | xargs -n 1 ./test_sync // write inline inode and sync
root@vm:/mnt/f2fs# rm -f 1
root@vm:/mnt/f2fs# sync
root@vm:/mnt/f2fs# f2fs_io gc_range // move data block in sync mode and not write CP
SPO, "fsck --dry-run" find inode has already checkpointed but still
with DENT_BIT_SHIFT set
The root cause is that GC does not clear the dentry mark and fsync mark
during node block migration, leading fsck to misinterpret them as
user-issued fsync writes.
In BGGC mode, node block migration is handled by f2fs_sync_node_pages(),
which guarantees the dentry and fsync marks are cleared before writing.
This patch move the set/clear of the fsync|dentry marks into
__write_node_folio to make the logic clearer, and ensures the
fsync|dentry mark is cleared in FGGC. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/CPU/AMD: Prevent improper isolation of shared resources in Zen2's op cache
Make sure resources are not improperly shared in the op cache and
cause instruction corruption this way. |
| In the Linux kernel, the following vulnerability has been resolved:
exit: prevent preemption of oopsing TASK_DEAD task
When an already-exiting task oopses, make_task_dead() currently calls
do_task_dead() with preemption enabled. That is forbidden:
do_task_dead() calls __schedule(), which has a comment saying "WARNING:
must be called with preemption disabled!".
If an oopsing task is preempted in do_task_dead(), between becoming
TASK_DEAD and entering the scheduler explicitly, bad things happen:
finish_task_switch() assumes that once the scheduler has switched away
from a TASK_DEAD task, the task can never run again and its stack is no
longer needed; but that assumption apparently doesn't hold if the dead
task was preempted (the SM_PREEMPT case).
This means that the scheduler ends up repeatedly dropping references on
the dead task's stack, which can lead to use-after-free or double-free
of the entire task stack; in other words, two tasks can end up running
on the same stack, resulting in various kinds of memory corruption.
(This does not just affect "recursively oopsing" tasks; it is enough to
oops once during task exit, for example in a file_operations::release
handler) |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: xfrm6: release dst on error in xfrm6_rcv_encap()
xfrm6_rcv_encap() performs an IPv6 route lookup when the skb does not
already have a dst attached. ip6_route_input_lookup() returns a
referenced dst entry even when the lookup resolves to an error route.
If dst->error is set, xfrm6_rcv_encap() drops the skb without attaching
the dst to the skb and without releasing the reference returned by the
lookup. Repeated packets hitting this path therefore leak dst entries.
Release the dst before jumping to the drop path. |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: kvm: fix vector context allocation leak
When the second kzalloc (host_context.vector.datap) fails in
kvm_riscv_vcpu_alloc_vector_context, the first allocation
(guest_context.vector.datap) is leaked. Free it before returning. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: pm: ADD_ADDR rtx: free sk if last
When an ADD_ADDR is retransmitted, the sk is held in sk_reset_timer(),
and released at the end.
If at that moment, it was the last reference being held, the sk would
not be freed. sock_put() should then be called instead of __sock_put().
But that's not enough: if it is the last reference, sock_put() will call
sk_free(), which will end up calling sk_stop_timer_sync() on the same
timer, and waiting indefinitely to finish. So it is needed to mark that
the timer is done at the end of the timer handler when it has not been
rescheduled, not to call sk_stop_timer_sync() on "itself". |
| In the Linux kernel, the following vulnerability has been resolved:
hfsplus: fix uninit-value by validating catalog record size
Syzbot reported a KMSAN uninit-value issue in hfsplus_strcasecmp(). The
root cause is that hfs_brec_read() doesn't validate that the on-disk
record size matches the expected size for the record type being read.
When mounting a corrupted filesystem, hfs_brec_read() may read less data
than expected. For example, when reading a catalog thread record, the
debug output showed:
HFSPLUS_BREC_READ: rec_len=520, fd->entrylength=26
HFSPLUS_BREC_READ: WARNING - entrylength (26) < rec_len (520) - PARTIAL READ!
hfs_brec_read() only validates that entrylength is not greater than the
buffer size, but doesn't check if it's less than expected. It successfully
reads 26 bytes into a 520-byte structure and returns success, leaving 494
bytes uninitialized.
This uninitialized data in tmp.thread.nodeName then gets copied by
hfsplus_cat_build_key_uni() and used by hfsplus_strcasecmp(), triggering
the KMSAN warning when the uninitialized bytes are used as array indices
in case_fold().
Fix by introducing hfsplus_brec_read_cat() wrapper that:
1. Calls hfs_brec_read() to read the data
2. Validates the record size based on the type field:
- Fixed size for folder and file records
- Variable size for thread records (depends on string length)
3. Returns -EIO if size doesn't match expected
For thread records, check against HFSPLUS_MIN_THREAD_SZ before reading
nodeName.length to avoid reading uninitialized data at call sites that
don't zero-initialize the entry structure.
Also initialize the tmp variable in hfsplus_find_cat() as defensive
programming to ensure no uninitialized data even if validation is
bypassed. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: fix scheduling with atomic in timestamp sockopt
Using lock_sock_fast() (atomic context) around sock_set_timestamp()
and sock_set_timestamping() is unsafe, as both helpers can sleep.
Replace lock_sock_fast() with sleepable lock_sock()/release_sock()
to avoid scheduling while atomic panic. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: usblp: fix uninitialized heap leak via LPGETSTATUS ioctl
Just like in a previous problem in this driver, usblp_ctrl_msg() will
collapse the usb_control_msg() return value to 0/-errno, discarding the
actual number of bytes transferred.
Ideally that short command should be detected and error out, but many
printers are known to send "incorrect" responses back so we can't just
do that.
statusbuf is kmalloc(8) at probe time and never filled before the first
LPGETSTATUS ioctl.
usblp_read_status() requests 1 byte. If a malicious printer responds
with zero bytes, *statusbuf is one byte of stale kmalloc heap,
sign-extended into the local int status, which the LPGETSTATUS path then
copy_to_user()s directly to the ioctl caller.
Fix this all by just zapping out the memory buffer when allocated at
probe time. If a later call does a short read, the data will be
identical to what the device sent it the last time, so there is no
"leak" of information happening. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: use safe list iteration in radar detect work
The call to ieee80211_dfs_cac_cancel can cause the iterated chanctx to
be freed and removed from the list. Guard against this to avoid a
slab-use-after-free error. |
