| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ARM: dts: exynos: Use Exynos5420 compatible for the MIPI video phy
For some reason, the driver adding support for Exynos5420 MIPI phy
back in 2016 wasn't used on Exynos5420, which caused a kernel panic.
Add the proper compatible for it. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Fix incomplete state save in rxe_requester
If a send packet is dropped by the IP layer in rxe_requester()
the call to rxe_xmit_packet() can fail with err == -EAGAIN.
To recover, the state of the wqe is restored to the state before
the packet was sent so it can be resent. However, the routines
that save and restore the state miss a significnt part of the
variable state in the wqe, the dma struct which is used to process
through the sge table. And, the state is not saved before the packet
is built which modifies the dma struct.
Under heavy stress testing with many QPs on a fast node sending
large messages to a slow node dropped packets are observed and
the resent packets are corrupted because the dma struct was not
restored. This patch fixes this behavior and allows the test cases
to succeed. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix __perf_event_overflow() vs perf_remove_from_context() race
Make sure that __perf_event_overflow() runs with IRQs disabled for all
possible callchains. Specifically the software events can end up running
it with only preemption disabled.
This opens up a race vs perf_event_exit_event() and friends that will go
and free various things the overflow path expects to be present, like
the BPF program. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: unconditionally bump set->nelems before insertion
In case that the set is full, a new element gets published then removed
without waiting for the RCU grace period, while RCU reader can be
walking over it already.
To address this issue, add the element transaction even if set is full,
but toggle the set_full flag to report -ENFILE so the abort path safely
unwinds the set to its previous state.
As for element updates, decrement set->nelems to restore it.
A simpler fix is to call synchronize_rcu() in the error path.
However, with a large batch adding elements to already maxed-out set,
this could cause noticeable slowdown of such batches. |
| In the Linux kernel, the following vulnerability has been resolved:
macvlan: observe an RCU grace period in macvlan_common_newlink() error path
valis reported that a race condition still happens after my prior patch.
macvlan_common_newlink() might have made @dev visible before
detecting an error, and its caller will directly call free_netdev(dev).
We must respect an RCU period, either in macvlan or the core networking
stack.
After adding a temporary mdelay(1000) in macvlan_forward_source_one()
to open the race window, valis repro was:
ip link add p1 type veth peer p2
ip link set address 00:00:00:00:00:20 dev p1
ip link set up dev p1
ip link set up dev p2
ip link add mv0 link p2 type macvlan mode source
(ip link add invalid% link p2 type macvlan mode source macaddr add
00:00:00:00:00:20 &) ; sleep 0.5 ; ping -c1 -I p1 1.2.3.4
PING 1.2.3.4 (1.2.3.4): 56 data bytes
RTNETLINK answers: Invalid argument
BUG: KASAN: slab-use-after-free in macvlan_forward_source
(drivers/net/macvlan.c:408 drivers/net/macvlan.c:444)
Read of size 8 at addr ffff888016bb89c0 by task e/175
CPU: 1 UID: 1000 PID: 175 Comm: e Not tainted 6.19.0-rc8+ #33 NONE
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl (lib/dump_stack.c:123)
print_report (mm/kasan/report.c:379 mm/kasan/report.c:482)
? macvlan_forward_source (drivers/net/macvlan.c:408 drivers/net/macvlan.c:444)
kasan_report (mm/kasan/report.c:597)
? macvlan_forward_source (drivers/net/macvlan.c:408 drivers/net/macvlan.c:444)
macvlan_forward_source (drivers/net/macvlan.c:408 drivers/net/macvlan.c:444)
? tasklet_init (kernel/softirq.c:983)
macvlan_handle_frame (drivers/net/macvlan.c:501)
Allocated by task 169:
kasan_save_stack (mm/kasan/common.c:58)
kasan_save_track (./arch/x86/include/asm/current.h:25
mm/kasan/common.c:70 mm/kasan/common.c:79)
__kasan_kmalloc (mm/kasan/common.c:419)
__kvmalloc_node_noprof (./include/linux/kasan.h:263 mm/slub.c:5657
mm/slub.c:7140)
alloc_netdev_mqs (net/core/dev.c:12012)
rtnl_create_link (net/core/rtnetlink.c:3648)
rtnl_newlink (net/core/rtnetlink.c:3830 net/core/rtnetlink.c:3957
net/core/rtnetlink.c:4072)
rtnetlink_rcv_msg (net/core/rtnetlink.c:6958)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
netlink_unicast (net/netlink/af_netlink.c:1319 net/netlink/af_netlink.c:1344)
netlink_sendmsg (net/netlink/af_netlink.c:1894)
__sys_sendto (net/socket.c:727 net/socket.c:742 net/socket.c:2206)
__x64_sys_sendto (net/socket.c:2209)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:131)
Freed by task 169:
kasan_save_stack (mm/kasan/common.c:58)
kasan_save_track (./arch/x86/include/asm/current.h:25
mm/kasan/common.c:70 mm/kasan/common.c:79)
kasan_save_free_info (mm/kasan/generic.c:587)
__kasan_slab_free (mm/kasan/common.c:287)
kfree (mm/slub.c:6674 mm/slub.c:6882)
rtnl_newlink (net/core/rtnetlink.c:3845 net/core/rtnetlink.c:3957
net/core/rtnetlink.c:4072)
rtnetlink_rcv_msg (net/core/rtnetlink.c:6958)
netlink_rcv_skb (net/netlink/af_netlink.c:2550)
netlink_unicast (net/netlink/af_netlink.c:1319 net/netlink/af_netlink.c:1344)
netlink_sendmsg (net/netlink/af_netlink.c:1894)
__sys_sendto (net/socket.c:727 net/socket.c:742 net/socket.c:2206)
__x64_sys_sendto (net/socket.c:2209)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:131) |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: xt_IDLETIMER: reject rev0 reuse of ALARM timer labels
IDLETIMER revision 0 rules reuse existing timers by label and always call
mod_timer() on timer->timer.
If the label was created first by revision 1 with XT_IDLETIMER_ALARM,
the object uses alarm timer semantics and timer->timer is never initialized.
Reusing that object from revision 0 causes mod_timer() on an uninitialized
timer_list, triggering debugobjects warnings and possible panic when
panic_on_warn=1.
Fix this by rejecting revision 0 rule insertion when an existing timer with
the same label is of ALARM type. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring: ensure ctx->rings is stable for task work flags manipulation
If DEFER_TASKRUN | SETUP_TASKRUN is used and task work is added while
the ring is being resized, it's possible for the OR'ing of
IORING_SQ_TASKRUN to happen in the small window of swapping into the
new rings and the old rings being freed.
Prevent this by adding a 2nd ->rings pointer, ->rings_rcu, which is
protected by RCU. The task work flags manipulation is inside RCU
already, and if the resize ring freeing is done post an RCU synchronize,
then there's no need to add locking to the fast path of task work
additions.
Note: this is only done for DEFER_TASKRUN, as that's the only setup mode
that supports ring resizing. If this ever changes, then they too need to
use the io_ctx_mark_taskrun() helper. |
| In the Linux kernel, the following vulnerability has been resolved:
net: add xmit recursion limit to tunnel xmit functions
Tunnel xmit functions (iptunnel_xmit, ip6tunnel_xmit) lack their own
recursion limit. When a bond device in broadcast mode has GRE tap
interfaces as slaves, and those GRE tunnels route back through the
bond, multicast/broadcast traffic triggers infinite recursion between
bond_xmit_broadcast() and ip_tunnel_xmit()/ip6_tnl_xmit(), causing
kernel stack overflow.
The existing XMIT_RECURSION_LIMIT (8) in the no-qdisc path is not
sufficient because tunnel recursion involves route lookups and full IP
output, consuming much more stack per level. Use a lower limit of 4
(IP_TUNNEL_RECURSION_LIMIT) to prevent overflow.
Add recursion detection using dev_xmit_recursion helpers directly in
iptunnel_xmit() and ip6tunnel_xmit() to cover all IPv4/IPv6 tunnel
paths including UDP encapsulated tunnels (VXLAN, Geneve, etc.).
Move dev_xmit_recursion helpers from net/core/dev.h to public header
include/linux/netdevice.h so they can be used by tunnel code.
BUG: KASAN: stack-out-of-bounds in blake2s.constprop.0+0xe7/0x160
Write of size 32 at addr ffff88810033fed0 by task kworker/0:1/11
Workqueue: mld mld_ifc_work
Call Trace:
<TASK>
__build_flow_key.constprop.0 (net/ipv4/route.c:515)
ip_rt_update_pmtu (net/ipv4/route.c:1073)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:84)
ip_tunnel_xmit (net/ipv4/ip_tunnel.c:847)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
ip_finish_output2 (net/ipv4/ip_output.c:237)
ip_output (net/ipv4/ip_output.c:438)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:86)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
ip_finish_output2 (net/ipv4/ip_output.c:237)
ip_output (net/ipv4/ip_output.c:438)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:86)
ip_tunnel_xmit (net/ipv4/ip_tunnel.c:847)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
mld_sendpack
mld_ifc_work
process_one_work
worker_thread
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: teql: fix NULL pointer dereference in iptunnel_xmit on TEQL slave xmit
teql_master_xmit() calls netdev_start_xmit(skb, slave) to transmit
through slave devices, but does not update skb->dev to the slave device
beforehand.
When a gretap tunnel is a TEQL slave, the transmit path reaches
iptunnel_xmit() which saves dev = skb->dev (still pointing to teql0
master) and later calls iptunnel_xmit_stats(dev, pkt_len). This
function does:
get_cpu_ptr(dev->tstats)
Since teql_master_setup() does not set dev->pcpu_stat_type to
NETDEV_PCPU_STAT_TSTATS, the core network stack never allocates tstats
for teql0, so dev->tstats is NULL. get_cpu_ptr(NULL) computes
NULL + __per_cpu_offset[cpu], resulting in a page fault.
BUG: unable to handle page fault for address: ffff8880e6659018
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 68bc067 P4D 68bc067 PUD 0
Oops: Oops: 0002 [#1] SMP KASAN PTI
RIP: 0010:iptunnel_xmit (./include/net/ip_tunnels.h:664 net/ipv4/ip_tunnel_core.c:89)
Call Trace:
<TASK>
ip_tunnel_xmit (net/ipv4/ip_tunnel.c:847)
__gre_xmit (net/ipv4/ip_gre.c:478)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
teql_master_xmit (net/sched/sch_teql.c:319)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
neigh_direct_output (net/core/neighbour.c:1660)
ip_finish_output2 (net/ipv4/ip_output.c:237)
__ip_finish_output.part.0 (net/ipv4/ip_output.c:315)
ip_mc_output (net/ipv4/ip_output.c:369)
ip_send_skb (net/ipv4/ip_output.c:1508)
udp_send_skb (net/ipv4/udp.c:1195)
udp_sendmsg (net/ipv4/udp.c:1485)
inet_sendmsg (net/ipv4/af_inet.c:859)
__sys_sendto (net/socket.c:2206)
Fix this by setting skb->dev = slave before calling
netdev_start_xmit(), so that tunnel xmit functions see the correct
slave device with properly allocated tstats. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: always walk all pending catchall elements
During transaction processing we might have more than one catchall element:
1 live catchall element and 1 pending element that is coming as part of the
new batch.
If the map holding the catchall elements is also going away, its
required to toggle all catchall elements and not just the first viable
candidate.
Otherwise, we get:
WARNING: ./include/net/netfilter/nf_tables.h:1281 at nft_data_release+0xb7/0xe0 [nf_tables], CPU#2: nft/1404
RIP: 0010:nft_data_release+0xb7/0xe0 [nf_tables]
[..]
__nft_set_elem_destroy+0x106/0x380 [nf_tables]
nf_tables_abort_release+0x348/0x8d0 [nf_tables]
nf_tables_abort+0xcf2/0x3ac0 [nf_tables]
nfnetlink_rcv_batch+0x9c9/0x20e0 [..] |
| Incorrect security UI in LookalikeChecks in Google Chrome on Android prior to 146.0.7680.71 allowed a remote attacker to perform UI spoofing via a crafted HTML page. (Chromium security severity: Medium) |
| Insufficient policy enforcement in PDF in Google Chrome on Android prior to 146.0.7680.71 allowed a remote attacker to bypass navigation restrictions via a crafted HTML page. (Chromium security severity: Medium) |
| Use after free in WebView in Google Chrome on Android prior to 146.0.7680.71 allowed a remote attacker to potentially exploit heap corruption via a crafted HTML page. (Chromium security severity: Medium) |
| Incorrect security UI in Downloads in Google Chrome on Android prior to 146.0.7680.71 allowed a remote attacker to perform UI spoofing via a crafted HTML page. (Chromium security severity: Low) |
| In the Linux kernel, the following vulnerability has been resolved:
mm/hugetlb: fix hugetlb_pmd_shared()
Patch series "mm/hugetlb: fixes for PMD table sharing (incl. using
mmu_gather)", v3.
One functional fix, one performance regression fix, and two related
comment fixes.
I cleaned up my prototype I recently shared [1] for the performance fix,
deferring most of the cleanups I had in the prototype to a later point.
While doing that I identified the other things.
The goal of this patch set is to be backported to stable trees "fairly"
easily. At least patch #1 and #4.
Patch #1 fixes hugetlb_pmd_shared() not detecting any sharing
Patch #2 + #3 are simple comment fixes that patch #4 interacts with.
Patch #4 is a fix for the reported performance regression due to excessive
IPI broadcasts during fork()+exit().
The last patch is all about TLB flushes, IPIs and mmu_gather.
Read: complicated
There are plenty of cleanups in the future to be had + one reasonable
optimization on x86. But that's all out of scope for this series.
Runtime tested, with a focus on fixing the performance regression using
the original reproducer [2] on x86.
This patch (of 4):
We switched from (wrongly) using the page count to an independent shared
count. Now, shared page tables have a refcount of 1 (excluding
speculative references) and instead use ptdesc->pt_share_count to identify
sharing.
We didn't convert hugetlb_pmd_shared(), so right now, we would never
detect a shared PMD table as such, because sharing/unsharing no longer
touches the refcount of a PMD table.
Page migration, like mbind() or migrate_pages() would allow for migrating
folios mapped into such shared PMD tables, even though the folios are not
exclusive. In smaps we would account them as "private" although they are
"shared", and we would be wrongly setting the PM_MMAP_EXCLUSIVE in the
pagemap interface.
Fix it by properly using ptdesc_pmd_is_shared() in hugetlb_pmd_shared(). |
| In the Linux kernel, the following vulnerability has been resolved:
leds: led-class: Only Add LED to leds_list when it is fully ready
Before this change the LED was added to leds_list before led_init_core()
gets called adding it the list before led_classdev.set_brightness_work gets
initialized.
This leaves a window where led_trigger_register() of a LED's default
trigger will call led_trigger_set() which calls led_set_brightness()
which in turn will end up queueing the *uninitialized*
led_classdev.set_brightness_work.
This race gets hit by the lenovo-thinkpad-t14s EC driver which registers
2 LEDs with a default trigger provided by snd_ctl_led.ko in quick
succession. The first led_classdev_register() causes an async modprobe of
snd_ctl_led to run and that async modprobe manages to exactly hit
the window where the second LED is on the leds_list without led_init_core()
being called for it, resulting in:
------------[ cut here ]------------
WARNING: CPU: 11 PID: 5608 at kernel/workqueue.c:4234 __flush_work+0x344/0x390
Hardware name: LENOVO 21N2S01F0B/21N2S01F0B, BIOS N42ET93W (2.23 ) 09/01/2025
...
Call trace:
__flush_work+0x344/0x390 (P)
flush_work+0x2c/0x50
led_trigger_set+0x1c8/0x340
led_trigger_register+0x17c/0x1c0
led_trigger_register_simple+0x84/0xe8
snd_ctl_led_init+0x40/0xf88 [snd_ctl_led]
do_one_initcall+0x5c/0x318
do_init_module+0x9c/0x2b8
load_module+0x7e0/0x998
Close the race window by moving the adding of the LED to leds_list to
after the led_init_core() call. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64/fpsimd: signal: Fix restoration of SVE context
When SME is supported, Restoring SVE signal context can go wrong in a
few ways, including placing the task into an invalid state where the
kernel may read from out-of-bounds memory (and may potentially take a
fatal fault) and/or may kill the task with a SIGKILL.
(1) Restoring a context with SVE_SIG_FLAG_SM set can place the task into
an invalid state where SVCR.SM is set (and sve_state is non-NULL)
but TIF_SME is clear, consequently resuting in out-of-bounds memory
reads and/or killing the task with SIGKILL.
This can only occur in unusual (but legitimate) cases where the SVE
signal context has either been modified by userspace or was saved in
the context of another task (e.g. as with CRIU), as otherwise the
presence of an SVE signal context with SVE_SIG_FLAG_SM implies that
TIF_SME is already set.
While in this state, task_fpsimd_load() will NOT configure SMCR_ELx
(leaving some arbitrary value configured in hardware) before
restoring SVCR and attempting to restore the streaming mode SVE
registers from memory via sve_load_state(). As the value of
SMCR_ELx.LEN may be larger than the task's streaming SVE vector
length, this may read memory outside of the task's allocated
sve_state, reading unrelated data and/or triggering a fault.
While this can result in secrets being loaded into streaming SVE
registers, these values are never exposed. As TIF_SME is clear,
fpsimd_bind_task_to_cpu() will configure CPACR_ELx.SMEN to trap EL0
accesses to streaming mode SVE registers, so these cannot be
accessed directly at EL0. As fpsimd_save_user_state() verifies the
live vector length before saving (S)SVE state to memory, no secret
values can be saved back to memory (and hence cannot be observed via
ptrace, signals, etc).
When the live vector length doesn't match the expected vector length
for the task, fpsimd_save_user_state() will send a fatal SIGKILL
signal to the task. Hence the task may be killed after executing
userspace for some period of time.
(2) Restoring a context with SVE_SIG_FLAG_SM clear does not clear the
task's SVCR.SM. If SVCR.SM was set prior to restoring the context,
then the task will be left in streaming mode unexpectedly, and some
register state will be combined inconsistently, though the task will
be left in legitimate state from the kernel's PoV.
This can only occur in unusual (but legitimate) cases where ptrace
has been used to set SVCR.SM after entry to the sigreturn syscall,
as syscall entry clears SVCR.SM.
In these cases, the the provided SVE register data will be loaded
into the task's sve_state using the non-streaming SVE vector length
and the FPSIMD registers will be merged into this using the
streaming SVE vector length.
Fix (1) by setting TIF_SME when setting SVCR.SM. This also requires
ensuring that the task's sme_state has been allocated, but as this could
contain live ZA state, it should not be zeroed. Fix (2) by clearing
SVCR.SM when restoring a SVE signal context with SVE_SIG_FLAG_SM clear.
For consistency, I've pulled the manipulation of SVCR, TIF_SVE, TIF_SME,
and fp_type earlier, immediately after the allocation of
sve_state/sme_state, before the restore of the actual register state.
This makes it easier to ensure that these are always modified
consistently, even if a fault is taken while reading the register data
from the signal context. I do not expect any software to depend on the
exact state restored when a fault is taken while reading the context. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvlan: Make the addrs_lock be per port
Make the addrs_lock be per port, not per ipvlan dev.
Initial code seems to be written in the assumption,
that any address change must occur under RTNL.
But it is not so for the case of IPv6. So
1) Introduce per-port addrs_lock.
2) It was needed to fix places where it was forgotten
to take lock (ipvlan_open/ipvlan_close)
This appears to be a very minor problem though.
Since it's highly unlikely that ipvlan_add_addr() will
be called on 2 CPU simultaneously. But nevertheless,
this could cause:
1) False-negative of ipvlan_addr_busy(): one interface
iterated through all port->ipvlans + ipvlan->addrs
under some ipvlan spinlock, and another added IP
under its own lock. Though this is only possible
for IPv6, since looks like only ipvlan_addr6_event() can be
called without rtnl_lock.
2) Race since ipvlan_ht_addr_add(port) is called under
different ipvlan->addrs_lock locks
This should not affect performance, since add/remove IP
is a rare situation and spinlock is not taken on fast
paths. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: fix devlink reload call trace
Commit 4da71a77fc3b ("ice: read internal temperature sensor") introduced
internal temperature sensor reading via HWMON. ice_hwmon_init() was added
to ice_init_feature() and ice_hwmon_exit() was added to ice_remove(). As a
result if devlink reload is used to reinit the device and then the driver
is removed, a call trace can occur.
BUG: unable to handle page fault for address: ffffffffc0fd4b5d
Call Trace:
string+0x48/0xe0
vsnprintf+0x1f9/0x650
sprintf+0x62/0x80
name_show+0x1f/0x30
dev_attr_show+0x19/0x60
The call trace repeats approximately every 10 minutes when system
monitoring tools (e.g., sadc) attempt to read the orphaned hwmon sysfs
attributes that reference freed module memory.
The sequence is:
1. Driver load, ice_hwmon_init() gets called from ice_init_feature()
2. Devlink reload down, flow does not call ice_remove()
3. Devlink reload up, ice_hwmon_init() gets called from
ice_init_feature() resulting in a second instance
4. Driver unload, ice_hwmon_exit() called from ice_remove() leaving the
first hwmon instance orphaned with dangling pointer
Fix this by moving ice_hwmon_exit() from ice_remove() to
ice_deinit_features() to ensure proper cleanup symmetry with
ice_hwmon_init(). |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: qfq: Use cl_is_active to determine whether class is active in qfq_rm_from_ag
This is more of a preventive patch to make the code more consistent and
to prevent possible exploits that employ child qlen manipulations on qfq.
use cl_is_active instead of relying on the child qdisc's qlen to determine
class activation. |
