| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid5-cache: fix null-ptr-deref for r5l_flush_stripe_to_raid()
r5l_flush_stripe_to_raid() will check if the list 'flushing_ios' is
empty, and then submit 'flush_bio', however, r5l_log_flush_endio()
is clearing the list first and then clear the bio, which will cause
null-ptr-deref:
T1: submit flush io
raid5d
handle_active_stripes
r5l_flush_stripe_to_raid
// list is empty
// add 'io_end_ios' to the list
bio_init
submit_bio
// io1
T2: io1 is done
r5l_log_flush_endio
list_splice_tail_init
// clear the list
T3: submit new flush io
...
r5l_flush_stripe_to_raid
// list is empty
// add 'io_end_ios' to the list
bio_init
bio_uninit
// clear bio->bi_blkg
submit_bio
// null-ptr-deref
Fix this problem by clearing bio before clearing the list in
r5l_log_flush_endio(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211_hwsim: Fix possible NULL dereference
In a call to mac80211_hwsim_select_tx_link() the sta pointer might
be NULL, thus need to check that it is not NULL before accessing it. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: nSVM: Load L1's TSC multiplier based on L1 state, not L2 state
When emulating nested VM-Exit, load L1's TSC multiplier if L1's desired
ratio doesn't match the current ratio, not if the ratio L1 is using for
L2 diverges from the default. Functionally, the end result is the same
as KVM will run L2 with L1's multiplier if L2's multiplier is the default,
i.e. checking that L1's multiplier is loaded is equivalent to checking if
L2 has a non-default multiplier.
However, the assertion that TSC scaling is exposed to L1 is flawed, as
userspace can trigger the WARN at will by writing the MSR and then
updating guest CPUID to hide the feature (modifying guest CPUID is
allowed anytime before KVM_RUN). E.g. hacking KVM's state_test
selftest to do
vcpu_set_msr(vcpu, MSR_AMD64_TSC_RATIO, 0);
vcpu_clear_cpuid_feature(vcpu, X86_FEATURE_TSCRATEMSR);
after restoring state in a new VM+vCPU yields an endless supply of:
------------[ cut here ]------------
WARNING: CPU: 10 PID: 206939 at arch/x86/kvm/svm/nested.c:1105
nested_svm_vmexit+0x6af/0x720 [kvm_amd]
Call Trace:
nested_svm_exit_handled+0x102/0x1f0 [kvm_amd]
svm_handle_exit+0xb9/0x180 [kvm_amd]
kvm_arch_vcpu_ioctl_run+0x1eab/0x2570 [kvm]
kvm_vcpu_ioctl+0x4c9/0x5b0 [kvm]
? trace_hardirqs_off+0x4d/0xa0
__se_sys_ioctl+0x7a/0xc0
__x64_sys_ioctl+0x21/0x30
do_syscall_64+0x41/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Unlike the nested VMRUN path, hoisting the svm->tsc_scaling_enabled check
into the if-statement is wrong as KVM needs to ensure L1's multiplier is
loaded in the above scenario. Alternatively, the WARN_ON() could simply
be deleted, but that would make KVM's behavior even more subtle, e.g. it's
not immediately obvious why it's safe to write MSR_AMD64_TSC_RATIO when
checking only tsc_ratio_msr. |
| In the Linux kernel, the following vulnerability has been resolved:
ublk: fail to recover device if queue setup is interrupted
In ublk_ctrl_end_recovery(), if wait_for_completion_interruptible() is
interrupted by signal, queues aren't setup successfully yet, so we
have to fail UBLK_CMD_END_USER_RECOVERY, otherwise kernel oops can be
triggered. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: resource leaks at mt7921_check_offload_capability()
Fixed coverity issue with resource leaks at variable "fw" going out of
scope leaks the storage it points to mt7921_check_offload_capability().
Addresses-Coverity-ID: 1527806 ("Resource leaks") |
| In the Linux kernel, the following vulnerability has been resolved:
ACPICA: Fix use-after-free in acpi_ut_copy_ipackage_to_ipackage()
There is an use-after-free reported by KASAN:
BUG: KASAN: use-after-free in acpi_ut_remove_reference+0x3b/0x82
Read of size 1 at addr ffff888112afc460 by task modprobe/2111
CPU: 0 PID: 2111 Comm: modprobe Not tainted 6.1.0-rc7-dirty
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
Call Trace:
<TASK>
kasan_report+0xae/0xe0
acpi_ut_remove_reference+0x3b/0x82
acpi_ut_copy_iobject_to_iobject+0x3be/0x3d5
acpi_ds_store_object_to_local+0x15d/0x3a0
acpi_ex_store+0x78d/0x7fd
acpi_ex_opcode_1A_1T_1R+0xbe4/0xf9b
acpi_ps_parse_aml+0x217/0x8d5
...
</TASK>
The root cause of the problem is that the acpi_operand_object
is freed when acpi_ut_walk_package_tree() fails in
acpi_ut_copy_ipackage_to_ipackage(), lead to repeated release in
acpi_ut_copy_iobject_to_iobject(). The problem was introduced
by "8aa5e56eeb61" commit, this commit is to fix memory leak in
acpi_ut_copy_iobject_to_iobject(), repeatedly adding remove
operation, lead to "acpi_operand_object" used after free.
Fix it by removing acpi_ut_remove_reference() in
acpi_ut_copy_ipackage_to_ipackage(). acpi_ut_copy_ipackage_to_ipackage()
is called to copy an internal package object into another internal
package object, when it fails, the memory of acpi_operand_object
should be freed by the caller. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libsas: Fix use-after-free bug in smp_execute_task_sg()
When executing SMP task failed, the smp_execute_task_sg() calls del_timer()
to delete "slow_task->timer". However, if the timer handler
sas_task_internal_timedout() is running, the del_timer() in
smp_execute_task_sg() will not stop it and a UAF will happen. The process
is shown below:
(thread 1) | (thread 2)
smp_execute_task_sg() | sas_task_internal_timedout()
... |
del_timer() |
... | ...
sas_free_task(task) |
kfree(task->slow_task) //FREE|
| task->slow_task->... //USE
Fix by calling del_timer_sync() in smp_execute_task_sg(), which makes sure
the timer handler have finished before the "task->slow_task" is
deallocated. |
| In the Linux kernel, the following vulnerability has been resolved:
rpmsg: char: Avoid double destroy of default endpoint
The rpmsg_dev_remove() in rpmsg_core is the place for releasing
this default endpoint.
So need to avoid destroying the default endpoint in
rpmsg_chrdev_eptdev_destroy(), this should be the same as
rpmsg_eptdev_release(). Otherwise there will be double destroy
issue that ept->refcount report warning:
refcount_t: underflow; use-after-free.
Call trace:
refcount_warn_saturate+0xf8/0x150
virtio_rpmsg_destroy_ept+0xd4/0xec
rpmsg_dev_remove+0x60/0x70
The issue can be reproduced by stopping remoteproc before
closing the /dev/rpmsgX. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: hisilicon/hpre - fix resource leak in remove process
In hpre_remove(), when the disable operation of qm sriov failed,
the following logic should continue to be executed to release the
remaining resources that have been allocated, instead of returning
directly, otherwise there will be resource leakage. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Fix UBSAN shift-out-of-bounds warning
If get_num_sdma_queues or get_num_xgmi_sdma_queues is 0, we end up
doing a shift operation where the number of bits shifted equals
number of bits in the operand. This behaviour is undefined.
Set num_sdma_queues or num_xgmi_sdma_queues to ULLONG_MAX, if the
count is >= number of bits in the operand.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1472 |
| TechAdvisor versions 2.6 through 3.37-30 for Dell XtremIO X2, contain(s) an Insertion of Sensitive Information into Log File vulnerability. A low privileged attacker with local access could potentially exploit this vulnerability, leading to Information exposure. The attacker may be able to use the exposed credentials to access the vulnerable application with privileges of the compromised account. |
| Improper access control in the Intel(R) oneAPI DPC++/C++ Compiler before version 2022.2.1 for some Intel(R) oneAPI Toolkits before version 2022.3.1 may allow authenticated user to potentially enable escalation of privilege via local access.
|
| Dell XtremIO, version(s) 6.4.0-22, contain(s) an Insertion of Sensitive Information into Log File vulnerability. A low privileged attacker with local access could potentially exploit this vulnerability, leading to Information exposure. The attacker may be able to use the exposed credentials to access the vulnerable application with privileges of the compromised account. |
| The SWD debug interface on the Growatt ShineLan-X communication dongle is available by default, allowing an attacker to attain debug access to the device and to extracting secrets or domains from within the device |
| ShineLan-X contains a set of credentials for an FTP server was found within the firmware, allowing testers to establish an insecure FTP connection with the server. This may allow an attacker to replace legitimate files being deployed to devices with their own malicious versions, since the firmware signature verification is not enforced. |
| ShineLan-X contains a stored cross site scripting (XSS) vulnerability in the local configuration web server. The JavaScript code snippet can be inserted in the communication module’s settings center. This may allow attackers to force a legitimate user’s browser’s JavaScript engine to run malicious code. |
| ShineLan-X contains a stored cross site scripting (XSS) vulnerability in the Plant Name field. A HTML payload will be displayed on the plant management page via a direct post. This may allow attackers to force a legitimate user’s browser’s JavaScript engine to run malicious code. |
| Growatt ShineLan-X communication dongle has an undocumented backup account with undocumented credentials which allows significant level access to the device, such as allowing any attacker to access the Setting Center. This means that this is effectively backdoor for all devices utilizing a Growatt ShineLan-X communication dongle. |
| Improper Limitation of a Pathname to a Restricted Directory (Path Traversal) vulnerability in Broadcom DX NetOps Spectrum on Windows, Linux allows Path Traversal.This issue affects DX NetOps Spectrum: 24.3.8 and earlier. |
| Improper Neutralization of Input During Web Page Generation (XSS or 'Cross-site Scripting') vulnerability in Broadcom DX NetOps Spectrum on Windows, Linux allows Reflected XSS.This issue affects DX NetOps Spectrum: 24.3.8 and earlier. |
