| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: Fix out-of-bounds memset in command slot handling
The remaining space in a command slot may be smaller than the size of
the command header. Clearing the command header with memset() before
verifying the available slot space can result in an out-of-bounds write
and memory corruption.
Fix this by moving the memset() call after the size validation. |
| In the Linux kernel, the following vulnerability has been resolved:
irqchip/sifive-plic: Fix frozen interrupt due to affinity setting
PLIC ignores interrupt completion message for disabled interrupt, explained
by the specification:
The PLIC signals it has completed executing an interrupt handler by
writing the interrupt ID it received from the claim to the
claim/complete register. The PLIC does not check whether the completion
ID is the same as the last claim ID for that target. If the completion
ID does not match an interrupt source that is currently enabled for
the target, the completion is silently ignored.
This caused problems in the past, because an interrupt can be disabled
while still being handled and plic_irq_eoi() had no effect. That was fixed
by checking if the interrupt is disabled, and if so enable it, before
sending the completion message. That check is done with irqd_irq_disabled().
However, that is not sufficient because the enable bit for the handling
hart can be zero despite irqd_irq_disabled(d) being false. This can happen
when affinity setting is changed while a hart is still handling the
interrupt.
This problem is easily reproducible by dumping a large file to uart (which
generates lots of interrupts) and at the same time keep changing the uart
interrupt's affinity setting. The uart port becomes frozen almost
instantaneously.
Fix this by checking PLIC's enable bit instead of irqd_irq_disabled(). |
| In the Linux kernel, the following vulnerability has been resolved:
atm: lec: fix null-ptr-deref in lec_arp_clear_vccs
syzkaller reported a null-ptr-deref in lec_arp_clear_vccs().
This issue can be easily reproduced using the syzkaller reproducer.
In the ATM LANE (LAN Emulation) module, the same atm_vcc can be shared by
multiple lec_arp_table entries (e.g., via entry->vcc or entry->recv_vcc).
When the underlying VCC is closed, lec_vcc_close() iterates over all
ARP entries and calls lec_arp_clear_vccs() for each matched entry.
For example, when lec_vcc_close() iterates through the hlists in
priv->lec_arp_empty_ones or other ARP tables:
1. In the first iteration, for the first matched ARP entry sharing the VCC,
lec_arp_clear_vccs() frees the associated vpriv (which is vcc->user_back)
and sets vcc->user_back to NULL.
2. In the second iteration, for the next matched ARP entry sharing the same
VCC, lec_arp_clear_vccs() is called again. It obtains a NULL vpriv from
vcc->user_back (via LEC_VCC_PRIV(vcc)) and then attempts to dereference it
via `vcc->pop = vpriv->old_pop`, leading to a null-ptr-deref crash.
Fix this by adding a null check for vpriv before dereferencing
it. If vpriv is already NULL, it means the VCC has been cleared
by a previous call, so we can safely skip the cleanup and just
clear the entry's vcc/recv_vcc pointers.
The entire cleanup block (including vcc_release_async()) is placed inside
the vpriv guard because a NULL vpriv indicates the VCC has already been
fully released by a prior iteration — repeating the teardown would
redundantly set flags and trigger callbacks on an already-closing socket.
The Fixes tag points to the initial commit because the entry->vcc path has
been vulnerable since the original code. The entry->recv_vcc path was later
added by commit 8d9f73c0ad2f ("atm: fix a memory leak of vcc->user_back")
with the same pattern, and both paths are fixed here. |
| In the Linux kernel, the following vulnerability has been resolved:
drbd: fix null-pointer dereference on local read error
In drbd_request_endio(), READ_COMPLETED_WITH_ERROR is passed to
__req_mod() with a NULL peer_device:
__req_mod(req, what, NULL, &m);
The READ_COMPLETED_WITH_ERROR handler then unconditionally passes this
NULL peer_device to drbd_set_out_of_sync(), which dereferences it,
causing a null-pointer dereference.
Fix this by obtaining the peer_device via first_peer_device(device),
matching how drbd_req_destroy() handles the same situation. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: mtk_eth_soc: Reset prog ptr to old_prog in case of error in mtk_xdp_setup()
Reset eBPF program pointer to old_prog and do not decrease its ref-count
if mtk_open routine in mtk_xdp_setup() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: fp9931: Fix PM runtime reference leak in fp9931_hwmon_read()
In fp9931_hwmon_read(), if regmap_read() failed, the function returned
the error code without calling pm_runtime_put_autosuspend(), causing
a PM reference leak. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix oops due to uninitialised var in smb2_unlink()
If SMB2_open_init() or SMB2_close_init() fails (e.g. reconnect), the
iovs set @rqst will be left uninitialised, hence calling
SMB2_open_free(), SMB2_close_free() or smb2_set_related() on them will
oops.
Fix this by initialising @close_iov and @open_iov before setting them
in @rqst. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: libertas: fix use-after-free in lbs_free_adapter()
The lbs_free_adapter() function uses timer_delete() (non-synchronous)
for both command_timer and tx_lockup_timer before the structure is
freed. This is incorrect because timer_delete() does not wait for
any running timer callback to complete.
If a timer callback is executing when lbs_free_adapter() is called,
the callback will access freed memory since lbs_cfg_free() frees the
containing structure immediately after lbs_free_adapter() returns.
Both timer callbacks (lbs_cmd_timeout_handler and lbs_tx_lockup_handler)
access priv->driver_lock, priv->cur_cmd, priv->dev, and other fields,
which would all be use-after-free violations.
Use timer_delete_sync() instead to ensure any running timer callback
has completed before returning.
This bug was introduced in commit 8f641d93c38a ("libertas: detect TX
lockups and reset hardware") where del_timer() was used instead of
del_timer_sync() in the cleanup path. The command_timer has had the
same issue since the driver was first written. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: Prevent ubuf size overflow
The ubuf size calculation may overflow, resulting in an undersized
allocation and possible memory corruption.
Use check_add_overflow() helpers to validate the size calculation before
allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix NULL pointer dereference in mesh_rx_csa_frame()
In mesh_rx_csa_frame(), elems->mesh_chansw_params_ie is dereferenced
at lines 1638 and 1642 without a prior NULL check:
ifmsh->chsw_ttl = elems->mesh_chansw_params_ie->mesh_ttl;
...
pre_value = le16_to_cpu(elems->mesh_chansw_params_ie->mesh_pre_value);
The mesh_matches_local() check above only validates the Mesh ID,
Mesh Configuration, and Supported Rates IEs. It does not verify the
presence of the Mesh Channel Switch Parameters IE (element ID 118).
When a received CSA action frame omits that IE, ieee802_11_parse_elems()
leaves elems->mesh_chansw_params_ie as NULL, and the unconditional
dereference causes a kernel NULL pointer dereference.
A remote mesh peer with an established peer link (PLINK_ESTAB) can
trigger this by sending a crafted SPECTRUM_MGMT/CHL_SWITCH action frame
that includes a matching Mesh ID and Mesh Configuration IE but omits the
Mesh Channel Switch Parameters IE. No authentication beyond the default
open mesh peering is required.
Crash confirmed on kernel 6.17.0-5-generic via mac80211_hwsim:
BUG: kernel NULL pointer dereference, address: 0000000000000000
Oops: Oops: 0000 [#1] SMP NOPTI
RIP: 0010:ieee80211_mesh_rx_queued_mgmt+0x143/0x2a0 [mac80211]
CR2: 0000000000000000
Fix by adding a NULL check for mesh_chansw_params_ie after
mesh_matches_local() returns, consistent with how other optional IEs
are guarded throughout the mesh code.
The bug has been present since v3.13 (released 2014-01-19). |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: always walk all pending catchall elements
During transaction processing we might have more than one catchall element:
1 live catchall element and 1 pending element that is coming as part of the
new batch.
If the map holding the catchall elements is also going away, its
required to toggle all catchall elements and not just the first viable
candidate.
Otherwise, we get:
WARNING: ./include/net/netfilter/nf_tables.h:1281 at nft_data_release+0xb7/0xe0 [nf_tables], CPU#2: nft/1404
RIP: 0010:nft_data_release+0xb7/0xe0 [nf_tables]
[..]
__nft_set_elem_destroy+0x106/0x380 [nf_tables]
nf_tables_abort_release+0x348/0x8d0 [nf_tables]
nf_tables_abort+0xcf2/0x3ac0 [nf_tables]
nfnetlink_rcv_batch+0x9c9/0x20e0 [..] |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: teql: fix NULL pointer dereference in iptunnel_xmit on TEQL slave xmit
teql_master_xmit() calls netdev_start_xmit(skb, slave) to transmit
through slave devices, but does not update skb->dev to the slave device
beforehand.
When a gretap tunnel is a TEQL slave, the transmit path reaches
iptunnel_xmit() which saves dev = skb->dev (still pointing to teql0
master) and later calls iptunnel_xmit_stats(dev, pkt_len). This
function does:
get_cpu_ptr(dev->tstats)
Since teql_master_setup() does not set dev->pcpu_stat_type to
NETDEV_PCPU_STAT_TSTATS, the core network stack never allocates tstats
for teql0, so dev->tstats is NULL. get_cpu_ptr(NULL) computes
NULL + __per_cpu_offset[cpu], resulting in a page fault.
BUG: unable to handle page fault for address: ffff8880e6659018
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 68bc067 P4D 68bc067 PUD 0
Oops: Oops: 0002 [#1] SMP KASAN PTI
RIP: 0010:iptunnel_xmit (./include/net/ip_tunnels.h:664 net/ipv4/ip_tunnel_core.c:89)
Call Trace:
<TASK>
ip_tunnel_xmit (net/ipv4/ip_tunnel.c:847)
__gre_xmit (net/ipv4/ip_gre.c:478)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
teql_master_xmit (net/sched/sch_teql.c:319)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
neigh_direct_output (net/core/neighbour.c:1660)
ip_finish_output2 (net/ipv4/ip_output.c:237)
__ip_finish_output.part.0 (net/ipv4/ip_output.c:315)
ip_mc_output (net/ipv4/ip_output.c:369)
ip_send_skb (net/ipv4/ip_output.c:1508)
udp_send_skb (net/ipv4/udp.c:1195)
udp_sendmsg (net/ipv4/udp.c:1485)
inet_sendmsg (net/ipv4/af_inet.c:859)
__sys_sendto (net/socket.c:2206)
Fix this by setting skb->dev = slave before calling
netdev_start_xmit(), so that tunnel xmit functions see the correct
slave device with properly allocated tstats. |
| In the Linux kernel, the following vulnerability has been resolved:
net: add xmit recursion limit to tunnel xmit functions
Tunnel xmit functions (iptunnel_xmit, ip6tunnel_xmit) lack their own
recursion limit. When a bond device in broadcast mode has GRE tap
interfaces as slaves, and those GRE tunnels route back through the
bond, multicast/broadcast traffic triggers infinite recursion between
bond_xmit_broadcast() and ip_tunnel_xmit()/ip6_tnl_xmit(), causing
kernel stack overflow.
The existing XMIT_RECURSION_LIMIT (8) in the no-qdisc path is not
sufficient because tunnel recursion involves route lookups and full IP
output, consuming much more stack per level. Use a lower limit of 4
(IP_TUNNEL_RECURSION_LIMIT) to prevent overflow.
Add recursion detection using dev_xmit_recursion helpers directly in
iptunnel_xmit() and ip6tunnel_xmit() to cover all IPv4/IPv6 tunnel
paths including UDP encapsulated tunnels (VXLAN, Geneve, etc.).
Move dev_xmit_recursion helpers from net/core/dev.h to public header
include/linux/netdevice.h so they can be used by tunnel code.
BUG: KASAN: stack-out-of-bounds in blake2s.constprop.0+0xe7/0x160
Write of size 32 at addr ffff88810033fed0 by task kworker/0:1/11
Workqueue: mld mld_ifc_work
Call Trace:
<TASK>
__build_flow_key.constprop.0 (net/ipv4/route.c:515)
ip_rt_update_pmtu (net/ipv4/route.c:1073)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:84)
ip_tunnel_xmit (net/ipv4/ip_tunnel.c:847)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
ip_finish_output2 (net/ipv4/ip_output.c:237)
ip_output (net/ipv4/ip_output.c:438)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:86)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
ip_finish_output2 (net/ipv4/ip_output.c:237)
ip_output (net/ipv4/ip_output.c:438)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:86)
ip_tunnel_xmit (net/ipv4/ip_tunnel.c:847)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
mld_sendpack
mld_ifc_work
process_one_work
worker_thread
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: xt_IDLETIMER: reject rev0 reuse of ALARM timer labels
IDLETIMER revision 0 rules reuse existing timers by label and always call
mod_timer() on timer->timer.
If the label was created first by revision 1 with XT_IDLETIMER_ALARM,
the object uses alarm timer semantics and timer->timer is never initialized.
Reusing that object from revision 0 causes mod_timer() on an uninitialized
timer_list, triggering debugobjects warnings and possible panic when
panic_on_warn=1.
Fix this by rejecting revision 0 rule insertion when an existing timer with
the same label is of ALARM type. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix __perf_event_overflow() vs perf_remove_from_context() race
Make sure that __perf_event_overflow() runs with IRQs disabled for all
possible callchains. Specifically the software events can end up running
it with only preemption disabled.
This opens up a race vs perf_event_exit_event() and friends that will go
and free various things the overflow path expects to be present, like
the BPF program. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: Only allow act_ct to bind to clsact/ingress qdiscs and shared blocks
As Paolo said earlier [1]:
"Since the blamed commit below, classify can return TC_ACT_CONSUMED while
the current skb being held by the defragmentation engine. As reported by
GangMin Kim, if such packet is that may cause a UaF when the defrag engine
later on tries to tuch again such packet."
act_ct was never meant to be used in the egress path, however some users
are attaching it to egress today [2]. Attempting to reach a middle
ground, we noticed that, while most qdiscs are not handling
TC_ACT_CONSUMED, clsact/ingress qdiscs are. With that in mind, we
address the issue by only allowing act_ct to bind to clsact/ingress
qdiscs and shared blocks. That way it's still possible to attach act_ct to
egress (albeit only with clsact).
[1] https://lore.kernel.org/netdev/674b8cbfc385c6f37fb29a1de08d8fe5c2b0fbee.1771321118.git.pabeni@redhat.com/
[2] https://lore.kernel.org/netdev/cc6bfb4a-4a2b-42d8-b9ce-7ef6644fb22b@ovn.org/ |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: bounds-check link_id in ieee80211_ml_reconfiguration
link_id is taken from the ML Reconfiguration element (control & 0x000f),
so it can be 0..15. link_removal_timeout[] has IEEE80211_MLD_MAX_NUM_LINKS
(15) elements, so index 15 is out-of-bounds. Skip subelements with
link_id >= IEEE80211_MLD_MAX_NUM_LINKS to avoid a stack out-of-bounds
write. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/exynos: vidi: use ctx->lock to protect struct vidi_context member variables related to memory alloc/free
Exynos Virtual Display driver performs memory alloc/free operations
without lock protection, which easily causes concurrency problem.
For example, use-after-free can occur in race scenario like this:
```
CPU0 CPU1 CPU2
---- ---- ----
vidi_connection_ioctl()
if (vidi->connection) // true
drm_edid = drm_edid_alloc(); // alloc drm_edid
...
ctx->raw_edid = drm_edid;
...
drm_mode_getconnector()
drm_helper_probe_single_connector_modes()
vidi_get_modes()
if (ctx->raw_edid) // true
drm_edid_dup(ctx->raw_edid);
if (!drm_edid) // false
...
vidi_connection_ioctl()
if (vidi->connection) // false
drm_edid_free(ctx->raw_edid); // free drm_edid
...
drm_edid_alloc(drm_edid->edid)
kmemdup(edid); // UAF!!
...
```
To prevent these vulns, at least in vidi_context, member variables related
to memory alloc/free should be protected with ctx->lock. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: cls_u32: use skb_header_pointer_careful()
skb_header_pointer() does not fully validate negative @offset values.
Use skb_header_pointer_careful() instead.
GangMin Kim provided a report and a repro fooling u32_classify():
BUG: KASAN: slab-out-of-bounds in u32_classify+0x1180/0x11b0
net/sched/cls_u32.c:221 |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: do not strictly require dirty metadata threshold for metadata writepages
[BUG]
There is an internal report that over 1000 processes are
waiting at the io_schedule_timeout() of balance_dirty_pages(), causing
a system hang and trigger a kernel coredump.
The kernel is v6.4 kernel based, but the root problem still applies to
any upstream kernel before v6.18.
[CAUSE]
From Jan Kara for his wisdom on the dirty page balance behavior first.
This cgroup dirty limit was what was actually playing the role here
because the cgroup had only a small amount of memory and so the dirty
limit for it was something like 16MB.
Dirty throttling is responsible for enforcing that nobody can dirty
(significantly) more dirty memory than there's dirty limit. Thus when
a task is dirtying pages it periodically enters into balance_dirty_pages()
and we let it sleep there to slow down the dirtying.
When the system is over dirty limit already (either globally or within
a cgroup of the running task), we will not let the task exit from
balance_dirty_pages() until the number of dirty pages drops below the
limit.
So in this particular case, as I already mentioned, there was a cgroup
with relatively small amount of memory and as a result with dirty limit
set at 16MB. A task from that cgroup has dirtied about 28MB worth of
pages in btrfs btree inode and these were practically the only dirty
pages in that cgroup.
So that means the only way to reduce the dirty pages of that cgroup is
to writeback the dirty pages of btrfs btree inode, and only after that
those processes can exit balance_dirty_pages().
Now back to the btrfs part, btree_writepages() is responsible for
writing back dirty btree inode pages.
The problem here is, there is a btrfs internal threshold that if the
btree inode's dirty bytes are below the 32M threshold, it will not
do any writeback.
This behavior is to batch as much metadata as possible so we won't write
back those tree blocks and then later re-COW them again for another
modification.
This internal 32MiB is higher than the existing dirty page size (28MiB),
meaning no writeback will happen, causing a deadlock between btrfs and
cgroup:
- Btrfs doesn't want to write back btree inode until more dirty pages
- Cgroup/MM doesn't want more dirty pages for btrfs btree inode
Thus any process touching that btree inode is put into sleep until
the number of dirty pages is reduced.
Thanks Jan Kara a lot for the analysis of the root cause.
[ENHANCEMENT]
Since kernel commit b55102826d7d ("btrfs: set AS_KERNEL_FILE on the
btree_inode"), btrfs btree inode pages will only be charged to the root
cgroup which should have a much larger limit than btrfs' 32MiB
threshold.
So it should not affect newer kernels.
But for all current LTS kernels, they are all affected by this problem,
and backporting the whole AS_KERNEL_FILE may not be a good idea.
Even for newer kernels I still think it's a good idea to get
rid of the internal threshold at btree_writepages(), since for most cases
cgroup/MM has a better view of full system memory usage than btrfs' fixed
threshold.
For internal callers using btrfs_btree_balance_dirty() since that
function is already doing internal threshold check, we don't need to
bother them.
But for external callers of btree_writepages(), just respect their
requests and write back whatever they want, ignoring the internal
btrfs threshold to avoid such deadlock on btree inode dirty page
balancing. |
