| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: gso: Forbid IPv6 TSO with extensions on devices with only IPV6_CSUM
When performing Generic Segmentation Offload (GSO) on an IPv6 packet that
contains extension headers, the kernel incorrectly requests checksum offload
if the egress device only advertises NETIF_F_IPV6_CSUM feature, which has
a strict contract: it supports checksum offload only for plain TCP or UDP
over IPv6 and explicitly does not support packets with extension headers.
The current GSO logic violates this contract by failing to disable the feature
for packets with extension headers, such as those used in GREoIPv6 tunnels.
This violation results in the device being asked to perform an operation
it cannot support, leading to a `skb_warn_bad_offload` warning and a collapse
of network throughput. While device TSO/USO is correctly bypassed in favor
of software GSO for these packets, the GSO stack must be explicitly told not
to request checksum offload.
Mask NETIF_F_IPV6_CSUM, NETIF_F_TSO6 and NETIF_F_GSO_UDP_L4
in gso_features_check if the IPv6 header contains extension headers to compute
checksum in software.
The exception is a BIG TCP extension, which, as stated in commit
68e068cabd2c6c53 ("net: reenable NETIF_F_IPV6_CSUM offload for BIG TCP packets"):
"The feature is only enabled on devices that support BIG TCP TSO.
The header is only present for PF_PACKET taps like tcpdump,
and not transmitted by physical devices."
kernel log output (truncated):
WARNING: CPU: 1 PID: 5273 at net/core/dev.c:3535 skb_warn_bad_offload+0x81/0x140
...
Call Trace:
<TASK>
skb_checksum_help+0x12a/0x1f0
validate_xmit_skb+0x1a3/0x2d0
validate_xmit_skb_list+0x4f/0x80
sch_direct_xmit+0x1a2/0x380
__dev_xmit_skb+0x242/0x670
__dev_queue_xmit+0x3fc/0x7f0
ip6_finish_output2+0x25e/0x5d0
ip6_finish_output+0x1fc/0x3f0
ip6_tnl_xmit+0x608/0xc00 [ip6_tunnel]
ip6gre_tunnel_xmit+0x1c0/0x390 [ip6_gre]
dev_hard_start_xmit+0x63/0x1c0
__dev_queue_xmit+0x6d0/0x7f0
ip6_finish_output2+0x214/0x5d0
ip6_finish_output+0x1fc/0x3f0
ip6_xmit+0x2ca/0x6f0
ip6_finish_output+0x1fc/0x3f0
ip6_xmit+0x2ca/0x6f0
inet6_csk_xmit+0xeb/0x150
__tcp_transmit_skb+0x555/0xa80
tcp_write_xmit+0x32a/0xe90
tcp_sendmsg_locked+0x437/0x1110
tcp_sendmsg+0x2f/0x50
...
skb linear: 00000000: e4 3d 1a 7d ec 30 e4 3d 1a 7e 5d 90 86 dd 60 0e
skb linear: 00000010: 00 0a 1b 34 3c 40 20 11 00 00 00 00 00 00 00 00
skb linear: 00000020: 00 00 00 00 00 12 20 11 00 00 00 00 00 00 00 00
skb linear: 00000030: 00 00 00 00 00 11 2f 00 04 01 04 01 01 00 00 00
skb linear: 00000040: 86 dd 60 0e 00 0a 1b 00 06 40 20 23 00 00 00 00
skb linear: 00000050: 00 00 00 00 00 00 00 00 00 12 20 23 00 00 00 00
skb linear: 00000060: 00 00 00 00 00 00 00 00 00 11 bf 96 14 51 13 f9
skb linear: 00000070: ae 27 a0 a8 2b e3 80 18 00 40 5b 6f 00 00 01 01
skb linear: 00000080: 08 0a 42 d4 50 d5 4b 70 f8 1a |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: Make cake_enqueue return NET_XMIT_CN when past buffer_limit
The following setup can trigger a WARNING in htb_activate due to
the condition: !cl->leaf.q->q.qlen
tc qdisc del dev lo root
tc qdisc add dev lo root handle 1: htb default 1
tc class add dev lo parent 1: classid 1:1 \
htb rate 64bit
tc qdisc add dev lo parent 1:1 handle f: \
cake memlimit 1b
ping -I lo -f -c1 -s64 -W0.001 127.0.0.1
This is because the low memlimit leads to a low buffer_limit, which
causes packet dropping. However, cake_enqueue still returns
NET_XMIT_SUCCESS, causing htb_enqueue to call htb_activate with an
empty child qdisc. We should return NET_XMIT_CN when packets are
dropped from the same tin and flow.
I do not believe return value of NET_XMIT_CN is necessary for packet
drops in the case of ack filtering, as that is meant to optimize
performance, not to signal congestion. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: core: config: Prevent OOB read in SS endpoint companion parsing
usb_parse_ss_endpoint_companion() checks descriptor type before length,
enabling a potentially odd read outside of the buffer size.
Fix this up by checking the size first before looking at any of the
fields in the descriptor. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: qgroup: fix race between quota disable and quota rescan ioctl
There's a race between a task disabling quotas and another running the
rescan ioctl that can result in a use-after-free of qgroup records from
the fs_info->qgroup_tree rbtree.
This happens as follows:
1) Task A enters btrfs_ioctl_quota_rescan() -> btrfs_qgroup_rescan();
2) Task B enters btrfs_quota_disable() and calls
btrfs_qgroup_wait_for_completion(), which does nothing because at that
point fs_info->qgroup_rescan_running is false (it wasn't set yet by
task A);
3) Task B calls btrfs_free_qgroup_config() which starts freeing qgroups
from fs_info->qgroup_tree without taking the lock fs_info->qgroup_lock;
4) Task A enters qgroup_rescan_zero_tracking() which starts iterating
the fs_info->qgroup_tree tree while holding fs_info->qgroup_lock,
but task B is freeing qgroup records from that tree without holding
the lock, resulting in a use-after-free.
Fix this by taking fs_info->qgroup_lock at btrfs_free_qgroup_config().
Also at btrfs_qgroup_rescan() don't start the rescan worker if quotas
were already disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Validate UAC3 cluster segment descriptors
UAC3 class segment descriptors need to be verified whether their sizes
match with the declared lengths and whether they fit with the
allocated buffer sizes, too. Otherwise malicious firmware may lead to
the unexpected OOB accesses. |
| In the Linux kernel, the following vulnerability has been resolved:
fs: Prevent file descriptor table allocations exceeding INT_MAX
When sysctl_nr_open is set to a very high value (for example, 1073741816
as set by systemd), processes attempting to use file descriptors near
the limit can trigger massive memory allocation attempts that exceed
INT_MAX, resulting in a WARNING in mm/slub.c:
WARNING: CPU: 0 PID: 44 at mm/slub.c:5027 __kvmalloc_node_noprof+0x21a/0x288
This happens because kvmalloc_array() and kvmalloc() check if the
requested size exceeds INT_MAX and emit a warning when the allocation is
not flagged with __GFP_NOWARN.
Specifically, when nr_open is set to 1073741816 (0x3ffffff8) and a
process calls dup2(oldfd, 1073741880), the kernel attempts to allocate:
- File descriptor array: 1073741880 * 8 bytes = 8,589,935,040 bytes
- Multiple bitmaps: ~400MB
- Total allocation size: > 8GB (exceeding INT_MAX = 2,147,483,647)
Reproducer:
1. Set /proc/sys/fs/nr_open to 1073741816:
# echo 1073741816 > /proc/sys/fs/nr_open
2. Run a program that uses a high file descriptor:
#include <unistd.h>
#include <sys/resource.h>
int main() {
struct rlimit rlim = {1073741824, 1073741824};
setrlimit(RLIMIT_NOFILE, &rlim);
dup2(2, 1073741880); // Triggers the warning
return 0;
}
3. Observe WARNING in dmesg at mm/slub.c:5027
systemd commit a8b627a introduced automatic bumping of fs.nr_open to the
maximum possible value. The rationale was that systems with memory
control groups (memcg) no longer need separate file descriptor limits
since memory is properly accounted. However, this change overlooked
that:
1. The kernel's allocation functions still enforce INT_MAX as a maximum
size regardless of memcg accounting
2. Programs and tests that legitimately test file descriptor limits can
inadvertently trigger massive allocations
3. The resulting allocations (>8GB) are impractical and will always fail
systemd's algorithm starts with INT_MAX and keeps halving the value
until the kernel accepts it. On most systems, this results in nr_open
being set to 1073741816 (0x3ffffff8), which is just under 1GB of file
descriptors.
While processes rarely use file descriptors near this limit in normal
operation, certain selftests (like
tools/testing/selftests/core/unshare_test.c) and programs that test file
descriptor limits can trigger this issue.
Fix this by adding a check in alloc_fdtable() to ensure the requested
allocation size does not exceed INT_MAX. This causes the operation to
fail with -EMFILE instead of triggering a kernel warning and avoids the
impractical >8GB memory allocation request. |
| In the Linux kernel, the following vulnerability has been resolved:
ARM: rockchip: fix kernel hang during smp initialization
In order to bring up secondary CPUs main CPU write trampoline
code to SRAM. The trampoline code is written while secondary
CPUs are powered on (at least that true for RK3188 CPU).
Sometimes that leads to kernel hang. Probably because secondary
CPU execute trampoline code while kernel doesn't expect.
The patch moves SRAM initialization step to the point where all
secondary CPUs are powered down.
That fixes rarely hangs on RK3188:
[ 0.091568] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.091996] rockchip_smp_prepare_cpus: ncores 4 |
| In the Linux kernel, the following vulnerability has been resolved:
rcu: Protect ->defer_qs_iw_pending from data race
On kernels built with CONFIG_IRQ_WORK=y, when rcu_read_unlock() is
invoked within an interrupts-disabled region of code [1], it will invoke
rcu_read_unlock_special(), which uses an irq-work handler to force the
system to notice when the RCU read-side critical section actually ends.
That end won't happen until interrupts are enabled at the soonest.
In some kernels, such as those booted with rcutree.use_softirq=y, the
irq-work handler is used unconditionally.
The per-CPU rcu_data structure's ->defer_qs_iw_pending field is
updated by the irq-work handler and is both read and updated by
rcu_read_unlock_special(). This resulted in the following KCSAN splat:
------------------------------------------------------------------------
BUG: KCSAN: data-race in rcu_preempt_deferred_qs_handler / rcu_read_unlock_special
read to 0xffff96b95f42d8d8 of 1 bytes by task 90 on cpu 8:
rcu_read_unlock_special+0x175/0x260
__rcu_read_unlock+0x92/0xa0
rt_spin_unlock+0x9b/0xc0
__local_bh_enable+0x10d/0x170
__local_bh_enable_ip+0xfb/0x150
rcu_do_batch+0x595/0xc40
rcu_cpu_kthread+0x4e9/0x830
smpboot_thread_fn+0x24d/0x3b0
kthread+0x3bd/0x410
ret_from_fork+0x35/0x40
ret_from_fork_asm+0x1a/0x30
write to 0xffff96b95f42d8d8 of 1 bytes by task 88 on cpu 8:
rcu_preempt_deferred_qs_handler+0x1e/0x30
irq_work_single+0xaf/0x160
run_irq_workd+0x91/0xc0
smpboot_thread_fn+0x24d/0x3b0
kthread+0x3bd/0x410
ret_from_fork+0x35/0x40
ret_from_fork_asm+0x1a/0x30
no locks held by irq_work/8/88.
irq event stamp: 200272
hardirqs last enabled at (200272): [<ffffffffb0f56121>] finish_task_switch+0x131/0x320
hardirqs last disabled at (200271): [<ffffffffb25c7859>] __schedule+0x129/0xd70
softirqs last enabled at (0): [<ffffffffb0ee093f>] copy_process+0x4df/0x1cc0
softirqs last disabled at (0): [<0000000000000000>] 0x0
------------------------------------------------------------------------
The problem is that irq-work handlers run with interrupts enabled, which
means that rcu_preempt_deferred_qs_handler() could be interrupted,
and that interrupt handler might contain an RCU read-side critical
section, which might invoke rcu_read_unlock_special(). In the strict
KCSAN mode of operation used by RCU, this constitutes a data race on
the ->defer_qs_iw_pending field.
This commit therefore disables interrupts across the portion of the
rcu_preempt_deferred_qs_handler() that updates the ->defer_qs_iw_pending
field. This suffices because this handler is not a fast path. |
| In the Linux kernel, the following vulnerability has been resolved:
jfs: truncate good inode pages when hard link is 0
The fileset value of the inode copy from the disk by the reproducer is
AGGR_RESERVED_I. When executing evict, its hard link number is 0, so its
inode pages are not truncated. This causes the bugon to be triggered when
executing clear_inode() because nrpages is greater than 0. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA: hfi1: fix possible divide-by-zero in find_hw_thread_mask()
The function divides number of online CPUs by num_core_siblings, and
later checks the divider by zero. This implies a possibility to get
and divide-by-zero runtime error. Fix it by moving the check prior to
division. This also helps to save one indentation level. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: do not allow relocation of partially dropped subvolumes
[BUG]
There is an internal report that balance triggered transaction abort,
with the following call trace:
item 85 key (594509824 169 0) itemoff 12599 itemsize 33
extent refs 1 gen 197740 flags 2
ref#0: tree block backref root 7
item 86 key (594558976 169 0) itemoff 12566 itemsize 33
extent refs 1 gen 197522 flags 2
ref#0: tree block backref root 7
...
BTRFS error (device loop0): extent item not found for insert, bytenr 594526208 num_bytes 16384 parent 449921024 root_objectid 934 owner 1 offset 0
BTRFS error (device loop0): failed to run delayed ref for logical 594526208 num_bytes 16384 type 182 action 1 ref_mod 1: -117
------------[ cut here ]------------
BTRFS: Transaction aborted (error -117)
WARNING: CPU: 1 PID: 6963 at ../fs/btrfs/extent-tree.c:2168 btrfs_run_delayed_refs+0xfa/0x110 [btrfs]
And btrfs check doesn't report anything wrong related to the extent
tree.
[CAUSE]
The cause is a little complex, firstly the extent tree indeed doesn't
have the backref for 594526208.
The extent tree only have the following two backrefs around that bytenr
on-disk:
item 65 key (594509824 METADATA_ITEM 0) itemoff 13880 itemsize 33
refs 1 gen 197740 flags TREE_BLOCK
tree block skinny level 0
(176 0x7) tree block backref root CSUM_TREE
item 66 key (594558976 METADATA_ITEM 0) itemoff 13847 itemsize 33
refs 1 gen 197522 flags TREE_BLOCK
tree block skinny level 0
(176 0x7) tree block backref root CSUM_TREE
But the such missing backref item is not an corruption on disk, as the
offending delayed ref belongs to subvolume 934, and that subvolume is
being dropped:
item 0 key (934 ROOT_ITEM 198229) itemoff 15844 itemsize 439
generation 198229 root_dirid 256 bytenr 10741039104 byte_limit 0 bytes_used 345571328
last_snapshot 198229 flags 0x1000000000001(RDONLY) refs 0
drop_progress key (206324 EXTENT_DATA 2711650304) drop_level 2
level 2 generation_v2 198229
And that offending tree block 594526208 is inside the dropped range of
that subvolume. That explains why there is no backref item for that
bytenr and why btrfs check is not reporting anything wrong.
But this also shows another problem, as btrfs will do all the orphan
subvolume cleanup at a read-write mount.
So half-dropped subvolume should not exist after an RW mount, and
balance itself is also exclusive to subvolume cleanup, meaning we
shouldn't hit a subvolume half-dropped during relocation.
The root cause is, there is no orphan item for this subvolume.
In fact there are 5 subvolumes from around 2021 that have the same
problem.
It looks like the original report has some older kernels running, and
caused those zombie subvolumes.
Thankfully upstream commit 8d488a8c7ba2 ("btrfs: fix subvolume/snapshot
deletion not triggered on mount") has long fixed the bug.
[ENHANCEMENT]
For repairing such old fs, btrfs-progs will be enhanced.
Considering how delayed the problem will show up (at run delayed ref
time) and at that time we have to abort transaction already, it is too
late.
Instead here we reject any half-dropped subvolume for reloc tree at the
earliest time, preventing confusion and extra time wasted on debugging
similar bugs. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/kmemleak: avoid soft lockup in __kmemleak_do_cleanup()
A soft lockup warning was observed on a relative small system x86-64
system with 16 GB of memory when running a debug kernel with kmemleak
enabled.
watchdog: BUG: soft lockup - CPU#8 stuck for 33s! [kworker/8:1:134]
The test system was running a workload with hot unplug happening in
parallel. Then kemleak decided to disable itself due to its inability to
allocate more kmemleak objects. The debug kernel has its
CONFIG_DEBUG_KMEMLEAK_MEM_POOL_SIZE set to 40,000.
The soft lockup happened in kmemleak_do_cleanup() when the existing
kmemleak objects were being removed and deleted one-by-one in a loop via a
workqueue. In this particular case, there are at least 40,000 objects
that need to be processed and given the slowness of a debug kernel and the
fact that a raw_spinlock has to be acquired and released in
__delete_object(), it could take a while to properly handle all these
objects.
As kmemleak has been disabled in this case, the object removal and
deletion process can be further optimized as locking isn't really needed.
However, it is probably not worth the effort to optimize for such an edge
case that should rarely happen. So the simple solution is to call
cond_resched() at periodic interval in the iteration loop to avoid soft
lockup. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/kmemleak: avoid deadlock by moving pr_warn() outside kmemleak_lock
When netpoll is enabled, calling pr_warn_once() while holding
kmemleak_lock in mem_pool_alloc() can cause a deadlock due to lock
inversion with the netconsole subsystem. This occurs because
pr_warn_once() may trigger netpoll, which eventually leads to
__alloc_skb() and back into kmemleak code, attempting to reacquire
kmemleak_lock.
This is the path for the deadlock.
mem_pool_alloc()
-> raw_spin_lock_irqsave(&kmemleak_lock, flags);
-> pr_warn_once()
-> netconsole subsystem
-> netpoll
-> __alloc_skb
-> __create_object
-> raw_spin_lock_irqsave(&kmemleak_lock, flags);
Fix this by setting a flag and issuing the pr_warn_once() after
kmemleak_lock is released. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: 8250: fix panic due to PSLVERR
When the PSLVERR_RESP_EN parameter is set to 1, the device generates
an error response if an attempt is made to read an empty RBR (Receive
Buffer Register) while the FIFO is enabled.
In serial8250_do_startup(), calling serial_port_out(port, UART_LCR,
UART_LCR_WLEN8) triggers dw8250_check_lcr(), which invokes
dw8250_force_idle() and serial8250_clear_and_reinit_fifos(). The latter
function enables the FIFO via serial_out(p, UART_FCR, p->fcr).
Execution proceeds to the serial_port_in(port, UART_RX).
This satisfies the PSLVERR trigger condition.
When another CPU (e.g., using printk()) is accessing the UART (UART
is busy), the current CPU fails the check (value & ~UART_LCR_SPAR) ==
(lcr & ~UART_LCR_SPAR) in dw8250_check_lcr(), causing it to enter
dw8250_force_idle().
Put serial_port_out(port, UART_LCR, UART_LCR_WLEN8) under the port->lock
to fix this issue.
Panic backtrace:
[ 0.442336] Oops - unknown exception [#1]
[ 0.442343] epc : dw8250_serial_in32+0x1e/0x4a
[ 0.442351] ra : serial8250_do_startup+0x2c8/0x88e
...
[ 0.442416] console_on_rootfs+0x26/0x70 |
| In the Linux kernel, the following vulnerability has been resolved:
iio: imu: bno055: fix OOB access of hw_xlate array
Fix a potential out-of-bounds array access of the hw_xlate array in
bno055.c.
In bno055_get_regmask(), hw_xlate was iterated over the length of the
vals array instead of the length of the hw_xlate array. In the case of
bno055_gyr_scale, the vals array is larger than the hw_xlate array,
so this could result in an out-of-bounds access. In practice, this
shouldn't happen though because a match should always be found which
breaks out of the for loop before it iterates beyond the end of the
hw_xlate array.
By adding a new hw_xlate_len field to the bno055_sysfs_attr, we can be
sure we are iterating over the correct length. |
| In the Linux kernel, the following vulnerability has been resolved:
vsock/virtio: Validate length in packet header before skb_put()
When receiving a vsock packet in the guest, only the virtqueue buffer
size is validated prior to virtio_vsock_skb_rx_put(). Unfortunately,
virtio_vsock_skb_rx_put() uses the length from the packet header as the
length argument to skb_put(), potentially resulting in SKB overflow if
the host has gone wonky.
Validate the length as advertised by the packet header before calling
virtio_vsock_skb_rx_put(). |
| In the Linux kernel, the following vulnerability has been resolved:
parisc: Revise __get_user() to probe user read access
Because of the way read access support is implemented, read access
interruptions are only triggered at privilege levels 2 and 3. The
kernel executes at privilege level 0, so __get_user() never triggers
a read access interruption (code 26). Thus, it is currently possible
for user code to access a read protected address via a system call.
Fix this by probing read access rights at privilege level 3 (PRIV_USER)
and setting __gu_err to -EFAULT (-14) if access isn't allowed.
Note the cmpiclr instruction does a 32-bit compare because COND macro
doesn't work inside asm. |
| In the Linux kernel, the following vulnerability has been resolved:
parisc: Revise gateway LWS calls to probe user read access
We use load and stbys,e instructions to trigger memory reference
interruptions without writing to memory. Because of the way read
access support is implemented, read access interruptions are only
triggered at privilege levels 2 and 3. The kernel and gateway
page execute at privilege level 0, so this code never triggers
a read access interruption. Thus, it is currently possible for
user code to execute a LWS compare and swap operation at an
address that is read protected at privilege level 3 (PRIV_USER).
Fix this by probing read access rights at privilege level 3 and
branching to lws_fault if access isn't allowed. |
| In the Linux kernel, the following vulnerability has been resolved:
media: usbtv: Lock resolution while streaming
When an program is streaming (ffplay) and another program (qv4l2)
changes the TV standard from NTSC to PAL, the kernel crashes due to trying
to copy to unmapped memory.
Changing from NTSC to PAL increases the resolution in the usbtv struct,
but the video plane buffer isn't adjusted, so it overflows.
[hverkuil: call vb2_is_busy instead of vb2_is_streaming] |
| In the Linux kernel, the following vulnerability has been resolved:
media: rainshadow-cec: fix TOCTOU race condition in rain_interrupt()
In the interrupt handler rain_interrupt(), the buffer full check on
rain->buf_len is performed before acquiring rain->buf_lock. This
creates a Time-of-Check to Time-of-Use (TOCTOU) race condition, as
rain->buf_len is concurrently accessed and modified in the work
handler rain_irq_work_handler() under the same lock.
Multiple interrupt invocations can race, with each reading buf_len
before it becomes full and then proceeding. This can lead to both
interrupts attempting to write to the buffer, incrementing buf_len
beyond its capacity (DATA_SIZE) and causing a buffer overflow.
Fix this bug by moving the spin_lock() to before the buffer full
check. This ensures that the check and the subsequent buffer modification
are performed atomically, preventing the race condition. An corresponding
spin_unlock() is added to the overflow path to correctly release the
lock.
This possible bug was found by an experimental static analysis tool
developed by our team. |
