| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
misc: nsm: pin the module while the device is open
misc_open() installs a misc driver's file operations with fops_get(),
which pins file_operations::owner before replacing the file's f_op. The
NSM misc device leaves nsm_dev_fops.owner unset, so opening /dev/nsm does
not take a module reference on the nsm driver.
If the driver is built as a module, an open file descriptor can therefore
survive rmmod of the module that provides its ioctl callbacks. A later
ioctl through that descriptor can call into unloaded module text.
Set nsm_dev_fops.owner to THIS_MODULE so the misc core holds the module
while any /dev/nsm file descriptor is open, matching the lifetime
expectation for the installed file operations. |
| In the Linux kernel, the following vulnerability has been resolved:
mei: bus: access mei_device under device_lock on cleanup
Fix couple of problems in mei_cl_bus_dev_release():
mei_cl_flush_queues() is running without lock.
bus->file_list access after mei_dev_bus_put(bus) can become a
use-after-free if this was the last reference to bus.
Protect queues cleanup and WARN traversal by device lock there
to avoid the concurrent access problems.
Move WARN traversal before mei_dev_bus_put(bus).
This file uses bus variable name for mei_device, adjust
code of mei_cl_bus_dev_release() to use bus variable too. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB reads in rtw_get_wps_ie()
rtw_get_wps_ie() iterates over IE data from network frames without
validating that the IE header and payload fit within the remaining
buffer before reading them. Specifically:
- in_ie[cnt + 1] is read without checking cnt + 1 < in_len
- memcmp(&in_ie[cnt + 2], ...) accesses cnt + 2 without bounds check
- in_ie[cnt + 1] is used as length without verifying payload fits
Add bounds checks at the top of the loop body to break early if fewer
than 2 bytes remain for the IE header, or if the declared payload
extends past the end of the buffer. Also require at least 4 bytes of
payload before comparing the WPS OUI. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7925: drop TXRX_NOTIFY on non-mmio buses
PKT_TYPE_TXRX_NOTIFY is an mmio-only event, but mt7925_rx_check() and
mt7925_queue_rx_skb() dispatch it to mt7925_mac_tx_free() on every bus.
mt7925_mac_tx_free() cleans the DMA tx queues with
mt76_queue_tx_cleanup(), which calls queue_ops->tx_cleanup(). Only the
mmio queue ops implement that callback; on USB it is NULL, so a
TXRX_NOTIFY there calls a NULL pointer in the RX worker:
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:0x0
Call Trace:
mt7925_mac_tx_free+0x58/0x350 [mt7925_common]
mt7925_rx_check+0xe2/0x130 [mt7925_common]
mt76u_rx_worker+0x1b9/0x620 [mt76_usb]
Drop the event on non-mmio buses via mt76_is_mmio(), as in
commit 5683e1488aa9 ("wifi: mt76: connac: do not check WED status for
non-mmio devices"). |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: close a re-opened queue timer in the destructor
queue_delete() closes the queue timer, then frees it. snd_seq_timer_close()
clears q->timer->timeri. snd_use_lock_sync() then drains borrowers, and
snd_seq_timer_delete() frees q->timer.
A borrower can re-open the timer inside that window. A SET_QUEUE_CLIENT
that took a queueptr() use_lock reference before the queue was unlinked
runs snd_seq_timer_open() after the close. Open refuses re-open only while
timeri is set, and the close just cleared it, so it re-opens timeri.
snd_seq_timer_delete() does not close that instance. Its snd_seq_timer_stop()
is a no-op, because running was cleared first. So it frees q->timer with the
instance still live. The queue is freed next.
The instance stays on the global timer with callback_data pointing at the
freed queue. A non-owner START on the unlocked queue arms it. The next tick
derefs the freed queue in snd_seq_timer_interrupt().
Reachable by an unprivileged user with access to /dev/snd/seq. No CAP and
no queue ownership required.
Close any lingering instance in the destructor. There, ->timeri can no
longer change: the queue is unlinked and all use_lock borrowers have
drained, so no snd_seq_queue_use() can re-open it. Close it before clearing
q->timer. snd_timer_close() waits for any in-flight snd_seq_timer_interrupt()
to finish, and that callback still reads q->timer (via snd_seq_check_queue()),
so q->timer must stay valid until it drains. |
| In the Linux kernel, the following vulnerability has been resolved:
media: vivid: fix cleanup bugs in vivid_init()
When platform_device_register() fails in vivid_init(), the embedded
struct device in vivid_pdev has already been initialized by
device_initialize(), but the failure path jumps to free_output_strings
without dropping the device reference for the current platform device:
vivid_init()
-> platform_device_register(&vivid_pdev)
-> device_initialize(&vivid_pdev.dev)
-> setup_pdev_dma_masks(&vivid_pdev)
-> platform_device_add(&vivid_pdev)
This leads to a reference leak when platform_device_register() fails.
Fix this by calling platform_device_put() before jumping to the common
cleanup path.
Also, the unreg_driver label incorrectly calls
platform_driver_register() instead of platform_driver_unregister(),
which breaks cleanup when workqueue creation fails after successful
driver registration. Fix that as well.
The reference leak was identified by a static analysis tool I developed
and confirmed by manual review. The incorrect cleanup call was found
during code inspection. |
| In the Linux kernel, the following vulnerability has been resolved:
media: stm32: dcmi: unregister notifier on probe failure
dcmi_graph_init() registers the async notifier before dcmi_probe() toggles
the reset line. If reset_control_assert() or reset_control_deassert()
fails afterwards, probe returns through err_cleanup and the driver core
will not call dcmi_remove().
Unregister the notifier before cleaning it up on that error path,
matching the successful remove path and the V4L2 async notifier lifetime
rules.
[hverkuil: added Fixes tag] |
| In the Linux kernel, the following vulnerability has been resolved:
media: stm32-dcmipp: Return queued buffers on start_streaming() failure
The vb2 framework hands buffers to the driver via buf_queue() before
calling start_streaming(). If start_streaming() returns an error
without first returning those buffers via vb2_buffer_done(),
vb2_start_streaming() fires WARN_ON(owned_by_drv_count) and the queued
buffers leak.
dcmipp_bytecap_start_streaming() returned -EINVAL when the source
subdevice could not be resolved from the media graph, before
pm_runtime_resume_and_get() and media_pipeline_start() had been called.
The remaining error paths already converge on the err_buffer_done
label, which calls dcmipp_bytecap_all_buffers_done(...,
VB2_BUF_STATE_QUEUED). Jump to that label directly: the intermediate
err_pm_put / err_media_pipeline_stop labels are skipped, which is
correct because nothing they would undo has happened yet.
This mirrors the uvcvideo fix in commit 4cf3b6fd54eb ("media: uvcvideo:
Return queued buffers on start_streaming() failure"). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: dce100: skip non-DP stream encoders for DP MST
On DCE8-class ASICs (e.g. Bonaire), the resource pool contains digital
DIG stream encoders plus one analog DAC encoder. When assigning a stream
encoder for a second DisplayPort MST stream, if the preferred digital
encoder is already acquired, dce100_find_first_free_match_stream_enc_for_link()
falls back to the first free pool entry. That entry may be the analog
encoder, whose funcs table lacks DP hooks such as dp_set_stream_attribute.
The subsequent atomic commit then dereferences NULL function pointers in
link_set_dpms_on() and crashes.
Skip encoders without dp_set_stream_attribute when the stream uses a DP
signal (including MST). Use dc_is_dp_signal(stream->signal) for the MST
fallback path instead of checking only the link connector signal.
Tested on:
- GPU: AMD Radeon R7 260X (Bonaire / DCE8)
- Board: Supermicro C9X299-PG300
- Setup: DP MST daisy chain, hotplug second monitor or have it connected on boot
- Kernel: 7.1.3 (issue observed since 6.19)
- Result: kernel oops without patch; dual monitors stable with patch
(cherry picked from commit 28ec64943e3ee4d9b8d30cea61e380f1429953a8) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: set new_stream to NULL after release
In dm_update_crtc_state(), the skip_modeset path releases new_stream
via dc_stream_release() but does not set the pointer to NULL.
If a later error (e.g., color management failure) triggers the fail
label, the error path calls dc_stream_release() again on the same
dangling pointer, causing a double release and potential use-after-free.
Fix this by setting new_stream to NULL after the initial release.
(cherry picked from commit 99f3af19073b3ddbfd96e789124cce12c4277b28) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/userq: fix indefinite fence wait during GPU reset
pre_reset only force-completes fences of MAPPED queues. A queue in any
other state (e.g. mid-eviction) keeps its last_fence pending; after a
GPU reset that fence never signals, so the eviction/suspend worker and
process teardown (amdgpu_evf_mgr_flush_suspend) wait on it forever and
wedge the machine:
INFO: task kworker/6:28 blocked for more than 120 seconds.
Workqueue: events amdgpu_eviction_fence_suspend_worker [amdgpu]
Call Trace:
dma_fence_wait_timeout+0x7e/0x130
amdgpu_userq_evict+0x67/0x140 [amdgpu]
amdgpu_eviction_fence_suspend_worker+0xd8/0x160 [amdgpu]
process_scheduled_works+0xa6/0x420
Force-complete every queue's fence regardless of state. The unmap and
mark-hung step stays gated on MAPPED, since unmapping a queue that is
not mapped is invalid.
(cherry picked from commit 9102b39fa924dcc3dc75a3137bfa9633c40b88c0) |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: Move jump_label_init() before parse_early_param()
When enabling both CONFIG_MEM_ALLOC_PROFILING=y and
CONFIG_MEM_ALLOC_PROFILING_ENABLED_BY_DEFAULT=y, then diabling memory
profiling by adding the boot parameter 'sysctl.vm.mem_profiling=0' will
cause the kernel failed to boot.
After analysis, this is because jump_label_init() must be called before
parse_early_param(), the early param handlers may modify static keys by
static_branch_enable/disable().
Fix this by moving jump_label_init() to before parse_early_param(). The
solution is similar to other architectures. |
| In the Linux kernel, the following vulnerability has been resolved:
binfmt_misc: set have_execfd only once the interpreter is opened
load_misc_binary() raises bprm->have_execfd as soon as it sees the 'O'
(or 'C') flag. This happens well before it opens the interpreter. If
that open fails the flag stays set on the bprm. binfmt_misc is at the
head of the format list so an interpreter open failure that returns
-ENOEXEC lets the search fall through to a later format. This means it
runs the matched binary directly having never staged an interpreter. So
bprm->executable is NULL while have_execfd falsely claims a descriptor
is present.
Consequently, begin_new_exec() dereferences the missing executable:
would_dump(bprm, bprm->executable);
and NULL derefs. Had it not, the hand-off later in the same function
would have failed anyway. FD_ADD(0, bprm->executable) rejects a NULL
file with -ENOMEM. Both sites are past the point of no return so the
exec cannot be unwound either way.
This can be reached by unprivileged users as binfmt_misc can be mounted
in user namespaces. So a user can register an 'O' entry whose
interpreter lives on a FUSE mount, have the FUSE server fail the open
with -ENOEXEC and execute a native ELF file that matches the entry.
have_execfd only means anything alongside the executable it describes
which is not set until the interpreter has been opened and staged.
So lets raise it there, next to execfd_creds, which is already set at
that point. An open failure now leaves it clear, so the fallback format
derives credentials from the binary and emits no AT_EXECFD, as it would
for any native exec. The argv rewrite load_misc_binary() performs before
the open is still not undone. This means the binary sees the interpreter
path in argv[0] and its own path in argv[1] but that predates this
change and only became observable once the exec stopped faulting. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: drop TXRX_NOTIFY on non-mmio buses
PKT_TYPE_TXRX_NOTIFY is an mmio-only event, but mt7921_rx_check() and
mt7921_queue_rx_skb() dispatch it to mt7921_mac_tx_free() on every bus.
mt7921_mac_tx_free() cleans the DMA tx queues with
mt76_queue_tx_cleanup(), which calls queue_ops->tx_cleanup(). Only the
mmio queue ops implement that callback; on USB and SDIO it is NULL, so
a TXRX_NOTIFY there calls a NULL pointer in the RX worker:
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:0x0
Call Trace:
mt7921_mac_tx_free+0x64/0x310 [mt7921_common]
mt7921_rx_check+0x5f/0xf0 [mt7921_common]
mt76u_rx_worker+0x1b9/0x620 [mt76_usb]
Drop the event on non-mmio buses via mt76_is_mmio(), as in
commit 5683e1488aa9 ("wifi: mt76: connac: do not check WED status for
non-mmio devices"). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath6kl: fix OOB access from firmware ADDBA window size
aggr_recv_addba_req_evt() logs a debug message when the firmware-supplied
win_sz is outside [AGGR_WIN_SZ_MIN, AGGR_WIN_SZ_MAX] but does not
return. The out-of-range win_sz is then used in TID_WINDOW_SZ() to
compute a kzalloc size and stored in rxtid->hold_q_sz, leading to
zero-size or overflowed allocations and subsequent out-of-bounds access.
Clean up any previously active aggregation session for the TID first,
then return early when win_sz is out of the valid range, instead of
proceeding with a broken allocation size. |
| In the Linux kernel, the following vulnerability has been resolved:
media: v4l2-fwnode: Fix subdev owner overwritten in v4l2_async_register_subdev_sensor()
The v4l2 helper v4l2_async_register_subdev_sensor() calls
v4l2_async_register_subdev(), which is a macro that expands to
__v4l2_async_register_subdev(sd,THIS_MODULE). Since the macro is expanded
inside v4l2-fwnode.c, THIS_MODULE resolves to the v4l2-fwnode module
rather than the sensor driver module that originally set sd->owner. When
v4l2-fwnode is built-in, THIS_MODULE evaluates to NULL, which then
overwrites the sensor driver's owner with NULL.
This causes the problem that the sensor module's reference count is never
incremented during async registration, so the module can be removed while
the subdevice is still in use by a notifier (e.g., a CSI-2 receiver
bridge driver).
Fix this by renaming v4l2_async_register_subdev_sensor() to
__v4l2_async_register_subdev_sensor() with an added explicit module
argument and introducing a wrapper macro:
#define v4l2_async_register_subdev_sensor(sd) \
__v4l2_async_register_subdev_sensor(sd, THIS_MODULE)
This ensures the sensor driver module is properly referenced even when
the sensor driver does not init the owner field before calling
v4l2_async_register_subdev_sensor() and prevents premature module removal. |
| In the Linux kernel, the following vulnerability has been resolved:
media: nxp: imx8-isi: Fix potential out-of-bounds issues
The maximum downscaling factor supported by ISI can be up to 16. Add
minimum value constraint before applying the setting to hardware.
Otherwise, the process will not respond even when Ctrl+C is executed. |
| In the Linux kernel, the following vulnerability has been resolved:
media: msi2500: Return queued buffers on start_streaming() failure
The vb2 framework hands buffers to the driver via buf_queue() before
calling start_streaming(). If start_streaming() returns an error
without first returning those buffers via vb2_buffer_done(),
vb2_start_streaming() fires WARN_ON(owned_by_drv_count) and the queued
buffers leak.
msi2500_start_streaming() had five error paths that all hit this trap
and were further tangled by ret-overwriting between calls:
- -ENODEV when the USB device was already disconnected
- -ERESTARTSYS when mutex_lock_interruptible() was interrupted
- msi2500_set_usb_adc() failure: ret was silently overwritten by
the next call (msi2500_isoc_init), so the error was lost entirely
- msi2500_isoc_init() failure: cleanup_queued_bufs was called, but
the function then fell through to msi2500_ctrl_msg() and again
masked the original error by overwriting ret
- msi2500_ctrl_msg(CMD_START_STREAMING) failure: no cleanup at all,
leaving isoc URBs submitted with no way for the driver to consume
them
Consolidate the error paths into a small goto chain. Every failure
now stops the function, drains the queued-buffer list, and returns
the real error code. The ctrl_msg failure path also rolls back the
preceding msi2500_isoc_init() via msi2500_isoc_cleanup() before
unlocking and draining.
The cleanup helper takes a vb2_buffer_state argument so that the
start_streaming error paths can pass VB2_BUF_STATE_QUEUED (as
expected by userspace on start_streaming failure) while stop_streaming
keeps its existing VB2_BUF_STATE_ERROR semantics.
This mirrors the uvcvideo fix in commit 4cf3b6fd54eb ("media: uvcvideo:
Return queued buffers on start_streaming() failure"). |
| In the Linux kernel, the following vulnerability has been resolved:
ublk: wait on ublk_dev_ready() instead of ub->completion
ub->completion is only re-armed by a successful START_USER_RECOVERY. If
the ublk server sends END_USER_RECOVERY without one - e.g. its START
failed with -EBUSY and the error was ignored - the wait is satisfied by
the stale completion of the previous recovery cycle, and the device is
marked LIVE and the requeue list kicked while the FETCH stream is still
running and ubq->canceling is still set. The kick redispatches a
previously requeued request, __ublk_queue_rq_common() sees ->canceling
and parks it again via __ublk_abort_rq(), and after the last FETCH
clears ->canceling nothing ever kicks the requeue list again: the
request is stranded there while holding its tag. If it is the flush
machinery's flush_rq, every subsequent fsync piles up in uninterruptible
sleep and teardown hangs on tag draining. This matches a report of a
lost PREFLUSH with ext4 on top of ublk after daemon crash recovery.
ub->completion is an edge-triggered latch used as a proxy for the level
condition "every queue has fetched all I/O commands", which can regress
(F_BATCH's UNPREP, daemon death) and whose re-arm can be skipped. Drop
it and wait on the real condition instead: the new helper
ublk_wait_dev_ready_and_lock() waits on ublk_dev_ready() via
wait_var_event_interruptible(), woken from ublk_mark_io_ready(), then
re-checks it under ub->mutex, waiting again on regression, and returns
with the mutex held and readiness guaranteed.
Readiness becomes true in the same ub->mutex critical section that
clears the last queue's ->canceling, so END_USER_RECOVERY marks the
device LIVE and kicks the requeue list strictly after ->canceling
clears. The wait stays interruptible, so a server whose daemon died can
still be signalled out. For ublk_ctrl_start_dev() this replaces the
fail-fast -EINVAL on an F_BATCH ready->UNPREP regression with waiting
until the device is ready again. |
| In the Linux kernel, the following vulnerability has been resolved:
media: pwc: Drain fill_buf on start_streaming() failure
pwc_isoc_init() submits its isochronous URBs with
usb_submit_urb(.., GFP_KERNEL) in a loop. After the first URB is
submitted, its completion handler pwc_isoc_handler() can run on another
CPU before the loop finishes:
start_streaming()
pwc_isoc_init()
usb_submit_urb(urbs[0], GFP_KERNEL)
pwc_isoc_handler(urbs[0])
pdev->fill_buf =
pwc_get_next_fill_buf(pdev)
usb_submit_urb(urbs[i>0], ..) -> fails
pwc_isoc_cleanup(pdev) /* kills URBs */
return ret;
pwc_cleanup_queued_bufs(pdev, VB2_BUF_STATE_QUEUED)
pwc_get_next_fill_buf() detaches a buffer from pdev->queued_bufs and
stores it in pdev->fill_buf. The error path in start_streaming() only
drains pdev->queued_bufs, so the buffer parked in pdev->fill_buf is
leaked. vb2_start_streaming() then triggers
WARN_ON(owned_by_drv_count).
stop_streaming() already handles this since commit 80b0963e1698
("[media] pwc: fix WARN_ON"), which added the fill_buf drain in the
teardown path but not in the start_streaming() error path. Mirror that
handling on failure so start_streaming() returns with no buffer owned
by the driver.
Issue identified by automated review of the INV-003 series at
https://sashiko.dev/ |
