| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix type confusion in l2cap_ecred_reconf_rsp()
l2cap_ecred_reconf_rsp() casts the incoming data to struct
l2cap_ecred_conn_rsp (the ECRED *connection* response, 8 bytes with
result at offset 6) instead of struct l2cap_ecred_reconf_rsp (2 bytes
with result at offset 0).
This causes two problems:
- The sizeof(*rsp) length check requires 8 bytes instead of the
correct 2, so valid L2CAP_ECRED_RECONF_RSP packets are rejected
with -EPROTO.
- rsp->result reads from offset 6 instead of offset 0, returning
wrong data when the packet is large enough to pass the check.
Fix by using the correct type. Also pass the already byte-swapped
result variable to BT_DBG instead of the raw __le16 field. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_ct: drop pending enqueued packets on removal
Packets sitting in nfqueue might hold a reference to:
- templates that specify the conntrack zone, because a percpu area is
used and module removal is possible.
- conntrack timeout policies and helper, where object removal leave
a stale reference.
Since these objects can just go away, drop enqueued packets to avoid
stale reference to them.
If there is a need for finer grain removal, this logic can be revisited
to make selective packet drop upon dependencies. |
| In the Linux kernel, the following vulnerability has been resolved:
net: cpsw_new: Fix potential unregister of netdev that has not been registered yet
If an error occurs during register_netdev() for the first MAC in
cpsw_register_ports(), even though cpsw->slaves[0].ndev is set to NULL,
cpsw->slaves[1].ndev would remain unchanged. This could later cause
cpsw_unregister_ports() to attempt unregistering the second MAC.
To address this, add a check for ndev->reg_state before calling
unregister_netdev(). With this change, setting cpsw->slaves[i].ndev
to NULL becomes unnecessary and can be removed accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ftgmac100: fix ring allocation unwind on open failure
ftgmac100_alloc_rings() allocates rx_skbs, tx_skbs, rxdes, txdes, and
rx_scratch in stages. On intermediate failures it returned -ENOMEM
directly, leaking resources allocated earlier in the function.
Rework the failure path to use staged local unwind labels and free
allocated resources in reverse order before returning -ENOMEM. This
matches common netdev allocation cleanup style. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: idxd: Fix leaking event log memory
During the device remove process, the device is reset, causing the
configuration registers to go back to their default state, which is
zero. As the driver is checking if the event log support was enabled
before deallocating, it will fail if a reset happened before.
Do not check if the support was enabled, the check for 'idxd->evl'
being valid (only allocated if the HW capability is available) is
enough. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: check tdls flag in ieee80211_tdls_oper
When NL80211_TDLS_ENABLE_LINK is called, the code only checks if the
station exists but not whether it is actually a TDLS station. This
allows the operation to proceed for non-TDLS stations, causing
unintended side effects like modifying channel context and HT
protection before failing.
Add a check for sta->sta.tdls early in the ENABLE_LINK case, before
any side effects occur, to ensure the operation is only allowed for
actual TDLS peers. |
| Nefteprodukttekhnika BUK TS-G Gas Station Automation System 2.9.1 on Linux contains a SQL Injection vulnerability (CWE-89) in the system configuration module. A remote attacker can send specially crafted HTTP POST requests to the /php/request.php endpoint via the sql parameter in application/x-www-form-urlencoded data (e.g., action=do&sql=<query_here>&reload_driver=0) to execute arbitrary SQL commands and potentially achieve remote code execution. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: sockmap: Fix use-after-free of sk->sk_socket in sk_psock_verdict_data_ready().
syzbot reported use-after-free of AF_UNIX socket's sk->sk_socket
in sk_psock_verdict_data_ready(). [0]
In unix_stream_sendmsg(), the peer socket's ->sk_data_ready() is
called after dropping its unix_state_lock().
Although the sender socket holds the peer's refcount, it does not
prevent the peer's sock_orphan(), and the peer's sk_socket might
be freed after one RCU grace period.
Let's fetch the peer's sk->sk_socket and sk->sk_socket->ops under
RCU in sk_psock_verdict_data_ready().
[0]:
BUG: KASAN: slab-use-after-free in sk_psock_verdict_data_ready+0xec/0x590 net/core/skmsg.c:1278
Read of size 8 at addr ffff8880594da860 by task syz.4.1842/11013
CPU: 1 UID: 0 PID: 11013 Comm: syz.4.1842 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2026
Call Trace:
<TASK>
dump_stack_lvl+0xe8/0x150 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xba/0x230 mm/kasan/report.c:482
kasan_report+0x117/0x150 mm/kasan/report.c:595
sk_psock_verdict_data_ready+0xec/0x590 net/core/skmsg.c:1278
unix_stream_sendmsg+0x8a3/0xe80 net/unix/af_unix.c:2482
sock_sendmsg_nosec net/socket.c:721 [inline]
__sock_sendmsg net/socket.c:736 [inline]
____sys_sendmsg+0x972/0x9f0 net/socket.c:2585
___sys_sendmsg+0x2a5/0x360 net/socket.c:2639
__sys_sendmsg net/socket.c:2671 [inline]
__do_sys_sendmsg net/socket.c:2676 [inline]
__se_sys_sendmsg net/socket.c:2674 [inline]
__x64_sys_sendmsg+0x1bd/0x2a0 net/socket.c:2674
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x14d/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7facf899c819
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007facf9827028 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007facf8c15fa0 RCX: 00007facf899c819
RDX: 0000000000000000 RSI: 0000200000000500 RDI: 0000000000000004
RBP: 00007facf8a32c91 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007facf8c16038 R14: 00007facf8c15fa0 R15: 00007ffd41b01c78
</TASK>
Allocated by task 11013:
kasan_save_stack mm/kasan/common.c:57 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:78
unpoison_slab_object mm/kasan/common.c:340 [inline]
__kasan_slab_alloc+0x6c/0x80 mm/kasan/common.c:366
kasan_slab_alloc include/linux/kasan.h:253 [inline]
slab_post_alloc_hook mm/slub.c:4538 [inline]
slab_alloc_node mm/slub.c:4866 [inline]
kmem_cache_alloc_lru_noprof+0x2b8/0x640 mm/slub.c:4885
sock_alloc_inode+0x28/0xc0 net/socket.c:316
alloc_inode+0x6a/0x1b0 fs/inode.c:347
new_inode_pseudo include/linux/fs.h:3003 [inline]
sock_alloc net/socket.c:631 [inline]
__sock_create+0x12d/0x9d0 net/socket.c:1562
sock_create net/socket.c:1656 [inline]
__sys_socketpair+0x1c4/0x560 net/socket.c:1803
__do_sys_socketpair net/socket.c:1856 [inline]
__se_sys_socketpair net/socket.c:1853 [inline]
__x64_sys_socketpair+0x9b/0xb0 net/socket.c:1853
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x14d/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 15:
kasan_save_stack mm/kasan/common.c:57 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:78
kasan_save_free_info+0x46/0x50 mm/kasan/generic.c:584
poison_slab_object mm/kasan/common.c:253 [inline]
__kasan_slab_free+0x5c/0x80 mm/kasan/common.c:285
kasan_slab_free include/linux/kasan.h:235 [inline]
slab_free_hook mm/slub.c:2685 [inline]
slab_free mm/slub.c:6165 [inline]
kmem_cache_free+0x187/0x630 mm/slub.c:6295
rcu_do_batch kernel/rcu/tree.c:
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: macb: fix clk handling on PCI glue driver removal
platform_device_unregister() may still want to use the registered clks
during runtime resume callback.
Note that there is a commit d82d5303c4c5 ("net: macb: fix use after free
on rmmod") that addressed the similar problem of clk vs platform device
unregistration but just moved the bug to another place.
Save the pointers to clks into local variables for reuse after platform
device is unregistered.
BUG: KASAN: use-after-free in clk_prepare+0x5a/0x60
Read of size 8 at addr ffff888104f85e00 by task modprobe/597
CPU: 2 PID: 597 Comm: modprobe Not tainted 6.1.164+ #114
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.1-0-g3208b098f51a-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x8d/0xba
print_report+0x17f/0x496
kasan_report+0xd9/0x180
clk_prepare+0x5a/0x60
macb_runtime_resume+0x13d/0x410 [macb]
pm_generic_runtime_resume+0x97/0xd0
__rpm_callback+0xc8/0x4d0
rpm_callback+0xf6/0x230
rpm_resume+0xeeb/0x1a70
__pm_runtime_resume+0xb4/0x170
bus_remove_device+0x2e3/0x4b0
device_del+0x5b3/0xdc0
platform_device_del+0x4e/0x280
platform_device_unregister+0x11/0x50
pci_device_remove+0xae/0x210
device_remove+0xcb/0x180
device_release_driver_internal+0x529/0x770
driver_detach+0xd4/0x1a0
bus_remove_driver+0x135/0x260
driver_unregister+0x72/0xb0
pci_unregister_driver+0x26/0x220
__do_sys_delete_module+0x32e/0x550
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
</TASK>
Allocated by task 519:
kasan_save_stack+0x2c/0x50
kasan_set_track+0x21/0x30
__kasan_kmalloc+0x8e/0x90
__clk_register+0x458/0x2890
clk_hw_register+0x1a/0x60
__clk_hw_register_fixed_rate+0x255/0x410
clk_register_fixed_rate+0x3c/0xa0
macb_probe+0x1d8/0x42e [macb_pci]
local_pci_probe+0xd7/0x190
pci_device_probe+0x252/0x600
really_probe+0x255/0x7f0
__driver_probe_device+0x1ee/0x330
driver_probe_device+0x4c/0x1f0
__driver_attach+0x1df/0x4e0
bus_for_each_dev+0x15d/0x1f0
bus_add_driver+0x486/0x5e0
driver_register+0x23a/0x3d0
do_one_initcall+0xfd/0x4d0
do_init_module+0x18b/0x5a0
load_module+0x5663/0x7950
__do_sys_finit_module+0x101/0x180
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Freed by task 597:
kasan_save_stack+0x2c/0x50
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x50
__kasan_slab_free+0x106/0x180
__kmem_cache_free+0xbc/0x320
clk_unregister+0x6de/0x8d0
macb_remove+0x73/0xc0 [macb_pci]
pci_device_remove+0xae/0x210
device_remove+0xcb/0x180
device_release_driver_internal+0x529/0x770
driver_detach+0xd4/0x1a0
bus_remove_driver+0x135/0x260
driver_unregister+0x72/0xb0
pci_unregister_driver+0x26/0x220
__do_sys_delete_module+0x32e/0x550
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x6e/0xd8 |
| In the Linux kernel, the following vulnerability has been resolved:
iomap: fix invalid folio access when i_blkbits differs from I/O granularity
Commit aa35dd5cbc06 ("iomap: fix invalid folio access after
folio_end_read()") partially addressed invalid folio access for folios
without an ifs attached, but it did not handle the case where
1 << inode->i_blkbits matches the folio size but is different from the
granularity used for the IO, which means IO can be submitted for less
than the full folio for the !ifs case.
In this case, the condition:
if (*bytes_submitted == folio_len)
ctx->cur_folio = NULL;
in iomap_read_folio_iter() will not invalidate ctx->cur_folio, and
iomap_read_end() will still be called on the folio even though the IO
helper owns it and will finish the read on it.
Fix this by unconditionally invalidating ctx->cur_folio for the !ifs
case. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: add GFP_NOIO in the bio completion if needed
The bio completion path in the process context (e.g. dm-verity)
will directly call into decompression rather than trigger another
workqueue context for minimal scheduling latencies, which can
then call vm_map_ram() with GFP_KERNEL.
Due to insufficient memory, vm_map_ram() may generate memory
swapping I/O, which can cause submit_bio_wait to deadlock
in some scenarios.
Trimmed down the call stack, as follows:
f2fs_submit_read_io
submit_bio //bio_list is initialized.
mmc_blk_mq_recovery
z_erofs_endio
vm_map_ram
__pte_alloc_kernel
__alloc_pages_direct_reclaim
shrink_folio_list
__swap_writepage
submit_bio_wait //bio_list is non-NULL, hang!!!
Use memalloc_noio_{save,restore}() to wrap up this path. |
| In the Linux kernel, the following vulnerability has been resolved:
net: macb: properly unregister fixed rate clocks
The additional resources allocated with clk_register_fixed_rate() need
to be released with clk_unregister_fixed_rate(), otherwise they are lost. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: lag: Check for LAG device before creating debugfs
__mlx5_lag_dev_add_mdev() may return 0 (success) even when an error
occurs that is handled gracefully. Consequently, the initialization
flow proceeds to call mlx5_ldev_add_debugfs() even when there is no
valid LAG context.
mlx5_ldev_add_debugfs() blindly created the debugfs directory and
attributes. This exposed interfaces (like the members file) that rely on
a valid ldev pointer, leading to potential NULL pointer dereferences if
accessed when ldev is NULL.
Add a check to verify that mlx5_lag_dev(dev) returns a valid pointer
before attempting to create the debugfs entries. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix switchdev mode rollback in case of failure
If for some internal reason switchdev mode fails, we rollback to legacy
mode, before this patch, rollback will unregister the uplink netdev and
leave it unregistered causing the below kernel bug.
To fix this, we need to avoid netdev unregister by setting the proper
rollback flag 'MLX5_PRIV_FLAGS_SWITCH_LEGACY' to indicate legacy mode.
devlink (431) used greatest stack depth: 11048 bytes left
mlx5_core 0000:00:03.0: E-Switch: Disable: mode(LEGACY), nvfs(0), \
necvfs(0), active vports(0)
mlx5_core 0000:00:03.0: E-Switch: Supported tc chains and prios offload
mlx5_core 0000:00:03.0: Loading uplink representor for vport 65535
mlx5_core 0000:00:03.0: mlx5_cmd_out_err:816:(pid 456): \
QUERY_HCA_CAP(0x100) op_mod(0x0) failed, \
status bad parameter(0x3), syndrome (0x3a3846), err(-22)
mlx5_core 0000:00:03.0 enp0s3np0 (unregistered): Unloading uplink \
representor for vport 65535
------------[ cut here ]------------
kernel BUG at net/core/dev.c:12070!
Oops: invalid opcode: 0000 [#1] SMP NOPTI
CPU: 2 UID: 0 PID: 456 Comm: devlink Not tainted 6.16.0-rc3+ \
#9 PREEMPT(voluntary)
RIP: 0010:unregister_netdevice_many_notify+0x123/0xae0
...
Call Trace:
[ 90.923094] unregister_netdevice_queue+0xad/0xf0
[ 90.923323] unregister_netdev+0x1c/0x40
[ 90.923522] mlx5e_vport_rep_unload+0x61/0xc6
[ 90.923736] esw_offloads_enable+0x8e6/0x920
[ 90.923947] mlx5_eswitch_enable_locked+0x349/0x430
[ 90.924182] ? is_mp_supported+0x57/0xb0
[ 90.924376] mlx5_devlink_eswitch_mode_set+0x167/0x350
[ 90.924628] devlink_nl_eswitch_set_doit+0x6f/0xf0
[ 90.924862] genl_family_rcv_msg_doit+0xe8/0x140
[ 90.925088] genl_rcv_msg+0x18b/0x290
[ 90.925269] ? __pfx_devlink_nl_pre_doit+0x10/0x10
[ 90.925506] ? __pfx_devlink_nl_eswitch_set_doit+0x10/0x10
[ 90.925766] ? __pfx_devlink_nl_post_doit+0x10/0x10
[ 90.926001] ? __pfx_genl_rcv_msg+0x10/0x10
[ 90.926206] netlink_rcv_skb+0x52/0x100
[ 90.926393] genl_rcv+0x28/0x40
[ 90.926557] netlink_unicast+0x27d/0x3d0
[ 90.926749] netlink_sendmsg+0x1f7/0x430
[ 90.926942] __sys_sendto+0x213/0x220
[ 90.927127] ? __sys_recvmsg+0x6a/0xd0
[ 90.927312] __x64_sys_sendto+0x24/0x30
[ 90.927504] do_syscall_64+0x50/0x1c0
[ 90.927687] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 90.927929] RIP: 0033:0x7f7d0363e047 |
| In the Linux kernel, the following vulnerability has been resolved:
net/x25: Fix potential double free of skb
When alloc_skb fails in x25_queue_rx_frame it calls kfree_skb(skb) at
line 48 and returns 1 (error).
This error propagates back through the call chain:
x25_queue_rx_frame returns 1
|
v
x25_state3_machine receives the return value 1 and takes the else
branch at line 278, setting queued=0 and returning 0
|
v
x25_process_rx_frame returns queued=0
|
v
x25_backlog_rcv at line 452 sees queued=0 and calls kfree_skb(skb)
again
This would free the same skb twice. Looking at x25_backlog_rcv:
net/x25/x25_in.c:x25_backlog_rcv() {
...
queued = x25_process_rx_frame(sk, skb);
...
if (!queued)
kfree_skb(skb);
} |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject sleepable kprobe_multi programs at attach time
kprobe.multi programs run in atomic/RCU context and cannot sleep.
However, bpf_kprobe_multi_link_attach() did not validate whether the
program being attached had the sleepable flag set, allowing sleepable
helpers such as bpf_copy_from_user() to be invoked from a non-sleepable
context.
This causes a "sleeping function called from invalid context" splat:
BUG: sleeping function called from invalid context at ./include/linux/uaccess.h:169
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1787, name: sudo
preempt_count: 1, expected: 0
RCU nest depth: 2, expected: 0
Fix this by rejecting sleepable programs early in
bpf_kprobe_multi_link_attach(), before any further processing. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix incorrect pruning due to atomic fetch precision tracking
When backtrack_insn encounters a BPF_STX instruction with BPF_ATOMIC
and BPF_FETCH, the src register (or r0 for BPF_CMPXCHG) also acts as
a destination, thus receiving the old value from the memory location.
The current backtracking logic does not account for this. It treats
atomic fetch operations the same as regular stores where the src
register is only an input. This leads the backtrack_insn to fail to
propagate precision to the stack location, which is then not marked
as precise!
Later, the verifier's path pruning can incorrectly consider two states
equivalent when they differ in terms of stack state. Meaning, two
branches can be treated as equivalent and thus get pruned when they
should not be seen as such.
Fix it as follows: Extend the BPF_LDX handling in backtrack_insn to
also cover atomic fetch operations via is_atomic_fetch_insn() helper.
When the fetch dst register is being tracked for precision, clear it,
and propagate precision over to the stack slot. For non-stack memory,
the precision walk stops at the atomic instruction, same as regular
BPF_LDX. This covers all fetch variants.
Before:
0: (b7) r1 = 8 ; R1=8
1: (7b) *(u64 *)(r10 -8) = r1 ; R1=8 R10=fp0 fp-8=8
2: (b7) r2 = 0 ; R2=0
3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2) ; R2=8 R10=fp0 fp-8=mmmmmmmm
4: (bf) r3 = r10 ; R3=fp0 R10=fp0
5: (0f) r3 += r2
mark_precise: frame0: last_idx 5 first_idx 0 subseq_idx -1
mark_precise: frame0: regs=r2 stack= before 4: (bf) r3 = r10
mark_precise: frame0: regs=r2 stack= before 3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2)
mark_precise: frame0: regs=r2 stack= before 2: (b7) r2 = 0
6: R2=8 R3=fp8
6: (b7) r0 = 0 ; R0=0
7: (95) exit
After:
0: (b7) r1 = 8 ; R1=8
1: (7b) *(u64 *)(r10 -8) = r1 ; R1=8 R10=fp0 fp-8=8
2: (b7) r2 = 0 ; R2=0
3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2) ; R2=8 R10=fp0 fp-8=mmmmmmmm
4: (bf) r3 = r10 ; R3=fp0 R10=fp0
5: (0f) r3 += r2
mark_precise: frame0: last_idx 5 first_idx 0 subseq_idx -1
mark_precise: frame0: regs=r2 stack= before 4: (bf) r3 = r10
mark_precise: frame0: regs=r2 stack= before 3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2)
mark_precise: frame0: regs= stack=-8 before 2: (b7) r2 = 0
mark_precise: frame0: regs= stack=-8 before 1: (7b) *(u64 *)(r10 -8) = r1
mark_precise: frame0: regs=r1 stack= before 0: (b7) r1 = 8
6: R2=8 R3=fp8
6: (b7) r0 = 0 ; R0=0
7: (95) exit |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: qixis-fpga: Fix error handling for devm_regmap_init_mmio()
devm_regmap_init_mmio() returns an ERR_PTR() on failure, not NULL.
The original code checked for NULL which would never trigger on error,
potentially leading to an invalid pointer dereference.
Use IS_ERR() and PTR_ERR() to properly handle the error case. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/qaic: Handle DBC deactivation if the owner went away
When a DBC is released, the device sends a QAIC_TRANS_DEACTIVATE_FROM_DEV
transaction to the host over the QAIC_CONTROL MHI channel. QAIC handles
this by calling decode_deactivate() to release the resources allocated for
that DBC. Since that handling is done in the qaic_manage_ioctl() context,
if the user goes away before receiving and handling the deactivation, the
host will be out-of-sync with the DBCs available for use, and the DBC
resources will not be freed unless the device is removed. If another user
loads and requests to activate a network, then the device assigns the same
DBC to that network, QAIC will "indefinitely" wait for dbc->in_use = false,
leading the user process to hang.
As a solution to this, handle QAIC_TRANS_DEACTIVATE_FROM_DEV transactions
that are received after the user has gone away. |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/pci: Fix double free in dma-buf feature
The error path through vfio_pci_core_feature_dma_buf() ignores its
own advice to only use dma_buf_put() after dma_buf_export(), instead
falling through the entire unwind chain. In the unlikely event that
we encounter file descriptor exhaustion, this can result in an
unbalanced refcount on the vfio device and double free of allocated
objects.
Avoid this by moving the "put" directly into the error path and return
the errno rather than entering the unwind chain. |
