| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: meson-gx: fix return value check of mmc_add_host()
mmc_add_host() may return error, if we ignore its return value,
it will lead two issues:
1. The memory that allocated in mmc_alloc_host() is leaked.
2. In the remove() path, mmc_remove_host() will be called to
delete device, but it's not added yet, it will lead a kernel
crash because of null-ptr-deref in device_del().
Fix this by checking the return value and goto error path which
will call mmc_free_host(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Fix memory leak in kfd_mem_dmamap_userptr()
If the number of pages from the userptr BO differs from the SG BO then the
allocated memory for the SG table doesn't get freed before returning
-EINVAL, which may lead to a memory leak in some error paths. Fix this by
checking the number of pages before allocating memory for the SG table. |
| In the Linux kernel, the following vulnerability has been resolved:
fpga: prevent integer overflow in dfl_feature_ioctl_set_irq()
The "hdr.count * sizeof(s32)" multiplication can overflow on 32 bit
systems leading to memory corruption. Use array_size() to fix that. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: amba-pl011: avoid SBSA UART accessing DMACR register
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083 b901f001 794038a0 8b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
[1] https://developer.arm.com/documentation/den0094/c/?lang=en
[2] https://lists.xenproject.org/archives/html/xen-devel/2022-11/msg00543.html |
| In the Linux kernel, the following vulnerability has been resolved:
cpufreq: qcom-hw: Fix memory leak in qcom_cpufreq_hw_read_lut()
If "cpu_dev" fails to get opp table in qcom_cpufreq_hw_read_lut(),
the program will return, resulting in "table" resource is not released. |
| In the Linux kernel, the following vulnerability has been resolved:
EDAC/i10nm: fix refcount leak in pci_get_dev_wrapper()
As the comment of pci_get_domain_bus_and_slot() says, it returns
a PCI device with refcount incremented, so it doesn't need to
call an extra pci_dev_get() in pci_get_dev_wrapper(), and the PCI
device needs to be put in the error path. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: fix memory leak in bnxt_nvm_test()
Free the kzalloc'ed buffer before returning in the success path. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: visconti: Fix memory leak in visconti_register_pll()
@pll->rate_table has allocated memory by kmemdup(), if clk_hw_register()
fails, it should be freed, otherwise it will cause memory leak issue,
this patch fixes it. |
| In the Linux kernel, the following vulnerability has been resolved:
devlink: hold region lock when flushing snapshots
Netdevsim triggers a splat on reload, when it destroys regions
with snapshots pending:
WARNING: CPU: 1 PID: 787 at net/core/devlink.c:6291 devlink_region_snapshot_del+0x12e/0x140
CPU: 1 PID: 787 Comm: devlink Not tainted 6.1.0-07460-g7ae9888d6e1c #580
RIP: 0010:devlink_region_snapshot_del+0x12e/0x140
Call Trace:
<TASK>
devl_region_destroy+0x70/0x140
nsim_dev_reload_down+0x2f/0x60 [netdevsim]
devlink_reload+0x1f7/0x360
devlink_nl_cmd_reload+0x6ce/0x860
genl_family_rcv_msg_doit.isra.0+0x145/0x1c0
This is the locking assert in devlink_region_snapshot_del(),
we're supposed to be holding the region->snapshot_lock here. |
| In the Linux kernel, the following vulnerability has been resolved:
HSI: ssi_protocol: fix potential resource leak in ssip_pn_open()
ssip_pn_open() claims the HSI client's port with hsi_claim_port(). When
hsi_register_port_event() gets some error and returns a negetive value,
the HSI client's port should be released with hsi_release_port().
Fix it by calling hsi_release_port() when hsi_register_port_event() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: reject negative ifindex
Recent changes in net-next (commit 759ab1edb56c ("net: store netdevs
in an xarray")) refactored the handling of pre-assigned ifindexes
and let syzbot surface a latent problem in ovs. ovs does not validate
ifindex, making it possible to create netdev ports with negative
ifindex values. It's easy to repro with YNL:
$ ./cli.py --spec netlink/specs/ovs_datapath.yaml \
--do new \
--json '{"upcall-pid": 1, "name":"my-dp"}'
$ ./cli.py --spec netlink/specs/ovs_vport.yaml \
--do new \
--json '{"upcall-pid": "00000001", "name": "some-port0", "dp-ifindex":3,"ifindex":4294901760,"type":2}'
$ ip link show
-65536: some-port0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 7a:48:21:ad:0b:fb brd ff:ff:ff:ff:ff:ff
...
Validate the inputs. Now the second command correctly returns:
$ ./cli.py --spec netlink/specs/ovs_vport.yaml \
--do new \
--json '{"upcall-pid": "00000001", "name": "some-port0", "dp-ifindex":3,"ifindex":4294901760,"type":2}'
lib.ynl.NlError: Netlink error: Numerical result out of range
nl_len = 108 (92) nl_flags = 0x300 nl_type = 2
error: -34 extack: {'msg': 'integer out of range', 'unknown': [[type:4 len:36] b'\x0c\x00\x02\x00\x00\x00\x00\x00\x00\x00\x00\x00\x0c\x00\x03\x00\xff\xff\xff\x7f\x00\x00\x00\x00\x08\x00\x01\x00\x08\x00\x00\x00'], 'bad-attr': '.ifindex'}
Accept 0 since it used to be silently ignored. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: reject index allocation if $BITMAP is empty but blocks exist
Index allocation requires at least one bit in the $BITMAP attribute to
track usage of index entries. If the bitmap is empty while index blocks
are already present, this reflects on-disk corruption.
syzbot triggered this condition using a malformed NTFS image. During a
rename() operation involving a long filename (which spans multiple
index entries), the empty bitmap allowed the name to be added without
valid tracking. Subsequent deletion of the original entry failed with
-ENOENT, due to unexpected index state.
Reject such cases by verifying that the bitmap is not empty when index
blocks exist. |
| In the Linux kernel, the following vulnerability has been resolved:
ftrace: Fix softlockup in ftrace_module_enable
A soft lockup was observed when loading amdgpu module.
If a module has a lot of tracable functions, multiple calls
to kallsyms_lookup can spend too much time in RCU critical
section and with disabled preemption, causing kernel panic.
This is the same issue that was fixed in
commit d0b24b4e91fc ("ftrace: Prevent RCU stall on PREEMPT_VOLUNTARY
kernels") and commit 42ea22e754ba ("ftrace: Add cond_resched() to
ftrace_graph_set_hash()").
Fix it the same way by adding cond_resched() in ftrace_module_enable. |
| In the Linux kernel, the following vulnerability has been resolved:
amd/amdkfd: enhance kfd process check in switch partition
current switch partition only check if kfd_processes_table is empty.
kfd_prcesses_table entry is deleted in kfd_process_notifier_release, but
kfd_process tear down is in kfd_process_wq_release.
consider two processes:
Process A (workqueue) -> kfd_process_wq_release -> Access kfd_node member
Process B switch partition -> amdgpu_xcp_pre_partition_switch -> amdgpu_amdkfd_device_fini_sw
-> kfd_node tear down.
Process A and B may trigger a race as shown in dmesg log.
This patch is to resolve the race by adding an atomic kfd_process counter
kfd_processes_count, it increment as create kfd process, decrement as
finish kfd_process_wq_release.
v2: Put kfd_processes_count per kfd_dev, move decrement to kfd_process_destroy_pdds
and bug fix. (Philip Yang)
[3966658.307702] divide error: 0000 [#1] SMP NOPTI
[3966658.350818] i10nm_edac
[3966658.356318] CPU: 124 PID: 38435 Comm: kworker/124:0 Kdump: loaded Tainted
[3966658.356890] Workqueue: kfd_process_wq kfd_process_wq_release [amdgpu]
[3966658.362839] nfit
[3966658.366457] RIP: 0010:kfd_get_num_sdma_engines+0x17/0x40 [amdgpu]
[3966658.366460] Code: 00 00 e9 ac 81 02 00 66 66 2e 0f 1f 84 00 00 00 00 00 90 0f 1f 44 00 00 48 8b 4f 08 48 8b b7 00 01 00 00 8b 81 58 26 03 00 99 <f7> be b8 01 00 00 80 b9 70 2e 00 00 00 74 0b 83 f8 02 ba 02 00 00
[3966658.380967] x86_pkg_temp_thermal
[3966658.391529] RSP: 0018:ffffc900a0edfdd8 EFLAGS: 00010246
[3966658.391531] RAX: 0000000000000008 RBX: ffff8974e593b800 RCX: ffff888645900000
[3966658.391531] RDX: 0000000000000000 RSI: ffff888129154400 RDI: ffff888129151c00
[3966658.391532] RBP: ffff8883ad79d400 R08: 0000000000000000 R09: ffff8890d2750af4
[3966658.391532] R10: 0000000000000018 R11: 0000000000000018 R12: 0000000000000000
[3966658.391533] R13: ffff8883ad79d400 R14: ffffe87ff662ba00 R15: ffff8974e593b800
[3966658.391533] FS: 0000000000000000(0000) GS:ffff88fe7f600000(0000) knlGS:0000000000000000
[3966658.391534] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[3966658.391534] CR2: 0000000000d71000 CR3: 000000dd0e970004 CR4: 0000000002770ee0
[3966658.391535] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[3966658.391535] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
[3966658.391536] PKRU: 55555554
[3966658.391536] Call Trace:
[3966658.391674] deallocate_sdma_queue+0x38/0xa0 [amdgpu]
[3966658.391762] process_termination_cpsch+0x1ed/0x480 [amdgpu]
[3966658.399754] intel_powerclamp
[3966658.402831] kfd_process_dequeue_from_all_devices+0x5b/0xc0 [amdgpu]
[3966658.402908] kfd_process_wq_release+0x1a/0x1a0 [amdgpu]
[3966658.410516] coretemp
[3966658.434016] process_one_work+0x1ad/0x380
[3966658.434021] worker_thread+0x49/0x310
[3966658.438963] kvm_intel
[3966658.446041] ? process_one_work+0x380/0x380
[3966658.446045] kthread+0x118/0x140
[3966658.446047] ? __kthread_bind_mask+0x60/0x60
[3966658.446050] ret_from_fork+0x1f/0x30
[3966658.446053] Modules linked in: kpatch_20765354(OEK)
[3966658.455310] kvm
[3966658.464534] mptcp_diag xsk_diag raw_diag unix_diag af_packet_diag netlink_diag udp_diag act_pedit act_mirred act_vlan cls_flower kpatch_21951273(OEK) kpatch_18424469(OEK) kpatch_19749756(OEK)
[3966658.473462] idxd_mdev
[3966658.482306] kpatch_17971294(OEK) sch_ingress xt_conntrack amdgpu(OE) amdxcp(OE) amddrm_buddy(OE) amd_sched(OE) amdttm(OE) amdkcl(OE) intel_ifs iptable_mangle tcm_loop target_core_pscsi tcp_diag target_core_file inet_diag target_core_iblock target_core_user target_core_mod coldpgs kpatch_18383292(OEK) ip6table_nat ip6table_filter ip6_tables ip_set_hash_ipportip ip_set_hash_ipportnet ip_set_hash_ipport ip_set_bitmap_port xt_comment iptable_nat nf_nat iptable_filter ip_tables ip_set ip_vs_sh ip_vs_wrr ip_vs_rr ip_vs nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 sn_core_odd(OE) i40e overlay binfmt_misc tun bonding(OE) aisqos(OE) aisqo
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: fix potential use after free in iwl_mld_remove_link()
This code frees "link" by calling kfree_rcu(link, rcu_head) and then it
dereferences "link" to get the "link->fw_id". Save the "link->fw_id"
first to avoid a potential use after free. |
| In the Linux kernel, the following vulnerability has been resolved:
ring-buffer: Do not warn in ring_buffer_map_get_reader() when reader catches up
The function ring_buffer_map_get_reader() is a bit more strict than the
other get reader functions, and except for certain situations the
rb_get_reader_page() should not return NULL. If it does, it triggers a
warning.
This warning was triggering but after looking at why, it was because
another acceptable situation was happening and it wasn't checked for.
If the reader catches up to the writer and there's still data to be read
on the reader page, then the rb_get_reader_page() will return NULL as
there's no new page to get.
In this situation, the reader page should not be updated and no warning
should trigger. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Cache streams targeting link when performing LT automation
[WHY]
Last LT automation update can cause crash by referencing current_state and
calling into dc_update_planes_and_stream which may clobber current_state.
[HOW]
Cache relevant stream pointers and iterate through them instead of relying
on the current_state. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: avoid infinite loop due to incomplete zstd-compressed data
Currently, the decompression logic incorrectly spins if compressed
data is truncated in crafted (deliberately corrupted) images. |
| ntfs3 in the Linux kernel through 6.8.0 allows a physically proximate attacker to read kernel memory by mounting a filesystem (e.g., if a Linux distribution is configured to allow unprivileged mounts of removable media) and then leveraging local access to trigger an out-of-bounds read. A length value can be larger than the amount of memory allocated. NOTE: the supplier's perspective is that there is no vulnerability when an attack requires an attacker-modified filesystem image. |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: fix use-after-free bug of nilfs_root in nilfs_evict_inode()
During unmount process of nilfs2, nothing holds nilfs_root structure after
nilfs2 detaches its writer in nilfs_detach_log_writer(). However, since
nilfs_evict_inode() uses nilfs_root for some cleanup operations, it may
cause use-after-free read if inodes are left in "garbage_list" and
released by nilfs_dispose_list() at the end of nilfs_detach_log_writer().
Fix this issue by modifying nilfs_evict_inode() to only clear inode
without additional metadata changes that use nilfs_root if the file system
is degraded to read-only or the writer is detached. |
