| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: dts: qcom: monaco: Reserve full Gunyah metadata region
We observe spurious "Synchronous External Abort" exceptions
(ESR=0x96000010) and kernel crashes on Monaco-based platforms.
These faults are caused by the kernel inadvertently accessing
hypervisor-owned memory that is not properly marked as reserved.
>From boot log, The Qualcomm hypervisor reports the memory range
at 0x91a80000 of size 0x80000 (512 KiB) as hypervisor-owned:
qhee_hyp_assign_remove_memory: 0x91a80000/0x80000 -> ret 0
However, the EFI memory map provided by firmware only reserves the
subrange 0x91a40000–0x91a87fff (288 KiB). The remaining portion
(0x91a88000–0x91afffff) is incorrectly reported as conventional
memory (from efi debug):
efi: 0x000091a40000-0x000091a87fff [Reserved...]
efi: 0x000091a88000-0x0000938fffff [Conventional...]
As a result, the allocator may hand out PFNs inside the hypervisor
owned region, causing fatal aborts when the kernel accesses those
addresses.
Add a reserved-memory carveout for the Gunyah hypervisor metadata
at 0x91a80000 (512 KiB) and mark it as no-map so Linux does not
map or allocate from this area.
For the record:
Hyp version: gunyah-e78adb36e debug (2025-11-17 05:38:05 UTC)
UEFI Ver: 6.0.260122.BOOT.MXF.1.0.c1-00449-KODIAKLA-1 |
| In the Linux kernel, the following vulnerability has been resolved:
ice: ptp: don't WARN when controlling PF is unavailable
In VFIO passthrough setups, it is possible to pass through only a PF
which doesn't own the source timer. In that case the PTP controlling PF
(adapter->ctrl_pf) is never initialized in the VM, so ice_get_ctrl_ptp()
returns NULL and triggers WARN_ON() in ice_ptp_setup_pf().
Since this is an expected behavior in that configuration, replace
WARN_ON() with an informational message and return -EOPNOTSUPP. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ipa: fix event ring index not programmed for IPA v5.0+
For IPA v5.0+, the event ring index field moved from CH_C_CNTXT_0 to
CH_C_CNTXT_1. The v5.0 register definition intended to define this
field in the CH_C_CNTXT_1 fmask array but used the old identifier of
ERINDEX instead of CH_ERINDEX.
Without a valid event ring, GSI channels could never signal transfer
completions. This caused gsi_channel_trans_quiesce() to block
forever in wait_for_completion().
At least for IPA v5.2 this resolves an issue seen where runtime
suspend, system suspend, and remoteproc stop all hanged forever. It
also meant the IPA data path was completely non functional. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel/uncore: Fix die ID init and look up bugs
In snbep_pci2phy_map_init(), in the nr_node_ids > 8 path,
uncore_device_to_die() may return -1 when all CPUs associated
with the UBOX device are offline.
Remove the WARN_ON_ONCE(die_id == -1) check for two reasons:
- The current code breaks out of the loop. This is incorrect because
pci_get_device() does not guarantee iteration in domain or bus order,
so additional UBOX devices may be skipped during the scan.
- Returning -EINVAL is incorrect, since marking offline buses with
die_id == -1 is expected and should not be treated as an error.
Separately, when NUMA is disabled on a NUMA-capable platform,
pcibus_to_node() returns NUMA_NO_NODE, causing uncore_device_to_die()
to return -1 for all PCI devices. As a result,
spr_update_device_location(), used on Intel SPR and EMR, ignores the
corresponding PMON units and does not add them to the RB tree.
Fix this by using uncore_pcibus_to_dieid(), which retrieves topology
from the UBOX GIDNIDMAP register and works regardless of whether NUMA
is enabled in Linux. This requires snbep_pci2phy_map_init() to be
added in spr_uncore_pci_init().
Keep uncore_device_to_die() only for the nr_node_ids > 8 case, where
NUMA is expected to be enabled. |
| PraisonAI is a multi-agent teams system. Prior to version 4.6.37, the _safe_extractall helper that all recipe pull, recipe publish, and recipe unpack flows route through validates each archive member's name for absolute paths, .. segments, and resolved-path escape — but does not validate member.linkname, does not reject symlink/hardlink members, and calls tar.extractall(dest_dir) without filter="data". A bundle that contains a symlink with a name inside dest_dir but a linkname pointing outside it, followed by a regular file whose path traverses through the just-created symlink, escapes dest_dir and lets the attacker write arbitrary content to an attacker-chosen location on the victim's filesystem. This issue has been patched in version 4.6.37. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_subset: Fix unbalanced refcnt in geth_free
geth_alloc() increments the reference count, but geth_free() fails to
decrement it. This prevents the configuration of attributes via configfs
after unlinking the function.
Decrement the reference count in geth_free() to ensure proper cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_rndis: Protect RNDIS options with mutex
The class/subclass/protocol options are suspectible to race conditions
as they can be accessed concurrently through configfs.
Use existing mutex to protect these options. This issue was identified
during code inspection. |
| In the Linux kernel, the following vulnerability has been resolved:
net/ipv6: ioam6: prevent schema length wraparound in trace fill
ioam6_fill_trace_data() stores the schema contribution to the trace
length in a u8. With bit 22 enabled and the largest schema payload,
sclen becomes 1 + 1020 / 4, wraps from 256 to 0, and bypasses the
remaining-space check. __ioam6_fill_trace_data() then positions the
write cursor without reserving the schema area but still copies the
4-byte schema header and the full schema payload, overrunning the trace
buffer.
Keep sclen in an unsigned int so the remaining-space check and the write
cursor calculation both see the full schema length. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: Reinit dev->spinlock between attachments to low-level drivers
`struct comedi_device` is the main controlling structure for a COMEDI
device created by the COMEDI subsystem. It contains a member `spinlock`
containing a spin-lock that is initialized by the COMEDI subsystem, but
is reserved for use by a low-level driver attached to the COMEDI device
(at least since commit 25436dc9d84f ("Staging: comedi: remove RT
code")).
Some COMEDI devices (those created on initialization of the COMEDI
subsystem when the "comedi.comedi_num_legacy_minors" parameter is
non-zero) can be attached to different low-level drivers over their
lifetime using the `COMEDI_DEVCONFIG` ioctl command. This can result in
inconsistent lock states being reported when there is a mismatch in the
spin-lock locking levels used by each low-level driver to which the
COMEDI device has been attached. Fix it by reinitializing
`dev->spinlock` before calling the low-level driver's `attach` function
pointer if `CONFIG_LOCKDEP` is enabled. |
| PraisonAI is a multi-agent teams system. Prior to praisonai version 4.6.37 and praisonaiagents version 1.6.37, praisonaiagents resolves unresolved tool names against module globals and __main__ after it fails to match the declared tool list and the registry. With the default agent configuration, _perm_allow is None, so undeclared non-dangerous tool names are not rejected by the permission gate. An attacker who can influence tool-call names can therefore invoke unintended application callables that were never declared as tools. This issue has been patched in praisonai version 4.6.37 and praisonaiagents version 1.6.37. |
| PraisonAI is a multi-agent teams system. Prior to version 4.6.34, PraisonAI's MCP (Model Context Protocol) server (praisonai mcp serve) registers four file-handling tools by default — praisonai.rules.create, praisonai.rules.show, praisonai.rules.delete, and praisonai.workflow.show. Each accepts a path or filename string from MCP tools/call arguments and joins it onto ~/.praison/rules/ (or, for workflow.show, accepts an absolute path) with no containment check. The JSON-RPC dispatcher passes params["arguments"] blind to each handler via **kwargs without validating against the advertised input schema. By setting rule_name="../../<some-path>" an attacker walks out of the rules directory and writes any file the running user can write. Dropping a Python .pth file into the user site-packages directory escalates this primitive to arbitrary code execution in any subsequent Python process the user spawns — the next praisonai CLI invocation, an IDE script run, the user's python REPL, or any background Python service. This issue has been patched in version 4.6.34. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: prevent possible UaF in addrconf_permanent_addr()
The mentioned helper try to warn the user about an exceptional
condition, but the message is delivered too late, accessing the ipv6
after its possible deletion.
Reorder the statement to avoid the possible UaF; while at it, place the
warning outside the idev->lock as it needs no protection. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: reserve enough transaction items for qgroup ioctls
Currently our qgroup ioctls don't reserve any space, they just do a
transaction join, which does not reserve any space, neither for the quota
tree updates nor for the delayed refs generated when updating the quota
tree. The quota root uses the global block reserve, which is fine most of
the time since we don't expect a lot of updates to the quota root, or to
be too close to -ENOSPC such that other critical metadata updates need to
resort to the global reserve.
However this is not optimal, as not reserving proper space may result in a
transaction abort due to not reserving space for delayed refs and then
abusing the use of the global block reserve.
For example, the following reproducer (which is unlikely to model any
real world use case, but just to illustrate the problem), triggers such a
transaction abort due to -ENOSPC when running delayed refs:
$ cat test.sh
#!/bin/bash
DEV=/dev/nullb0
MNT=/mnt/nullb0
umount $DEV &> /dev/null
# Limit device to 1G so that it's much faster to reproduce the issue.
mkfs.btrfs -f -b 1G $DEV
mount -o commit=600 $DEV $MNT
fallocate -l 800M $MNT/filler
btrfs quota enable $MNT
for ((i = 1; i <= 400000; i++)); do
btrfs qgroup create 1/$i $MNT
done
umount $MNT
When running this, we can see in dmesg/syslog that a transaction abort
happened:
[436.490] BTRFS error (device nullb0): failed to run delayed ref for logical 30408704 num_bytes 16384 type 176 action 1 ref_mod 1: -28
[436.493] ------------[ cut here ]------------
[436.494] BTRFS: Transaction aborted (error -28)
[436.495] WARNING: fs/btrfs/extent-tree.c:2247 at btrfs_run_delayed_refs+0xd9/0x110 [btrfs], CPU#4: umount/2495372
[436.497] Modules linked in: btrfs loop (...)
[436.508] CPU: 4 UID: 0 PID: 2495372 Comm: umount Tainted: G W 6.19.0-rc8-btrfs-next-225+ #1 PREEMPT(full)
[436.510] Tainted: [W]=WARN
[436.511] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[436.513] RIP: 0010:btrfs_run_delayed_refs+0xdf/0x110 [btrfs]
[436.514] Code: 0f 82 ea (...)
[436.518] RSP: 0018:ffffd511850b7d78 EFLAGS: 00010292
[436.519] RAX: 00000000ffffffe4 RBX: ffff8f120dad37e0 RCX: 0000000002040001
[436.520] RDX: 0000000000000002 RSI: 00000000ffffffe4 RDI: ffffffffc090fd80
[436.522] RBP: 0000000000000000 R08: 0000000000000001 R09: ffffffffc04d1867
[436.523] R10: ffff8f18dc1fffa8 R11: 0000000000000003 R12: ffff8f173aa89400
[436.524] R13: 0000000000000000 R14: ffff8f173aa89400 R15: 0000000000000000
[436.526] FS: 00007fe59045d840(0000) GS:ffff8f192e22e000(0000) knlGS:0000000000000000
[436.527] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[436.528] CR2: 00007fe5905ff2b0 CR3: 000000060710a002 CR4: 0000000000370ef0
[436.530] Call Trace:
[436.530] <TASK>
[436.530] btrfs_commit_transaction+0x73/0xc00 [btrfs]
[436.531] ? btrfs_attach_transaction_barrier+0x1e/0x70 [btrfs]
[436.532] sync_filesystem+0x7a/0x90
[436.533] generic_shutdown_super+0x28/0x180
[436.533] kill_anon_super+0x12/0x40
[436.534] btrfs_kill_super+0x12/0x20 [btrfs]
[436.534] deactivate_locked_super+0x2f/0xb0
[436.534] cleanup_mnt+0xea/0x180
[436.535] task_work_run+0x58/0xa0
[436.535] exit_to_user_mode_loop+0xed/0x480
[436.536] ? __x64_sys_umount+0x68/0x80
[436.536] do_syscall_64+0x2a5/0xf20
[436.537] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[436.537] RIP: 0033:0x7fe5906b6217
[436.538] Code: 0d 00 f7 (...)
[436.540] RSP: 002b:00007ffcd87a61f8 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
[436.541] RAX: 0000000000000000 RBX: 00005618b9ecadc8 RCX: 00007fe5906b6217
[436.541] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00005618b9ecb100
[436.542] RBP: 0000000000000000 R08: 00007ffcd87a4fe0 R09: 00000000ffffffff
[436.544] R10: 0000000000000103 R11:
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix NULL pointer dereference in dcn401_init_hw()
dcn401_init_hw() assumes that update_bw_bounding_box() is valid when
entering the update path. However, the existing condition:
((!fams2_enable && update_bw_bounding_box) || freq_changed)
does not guarantee this, as the freq_changed branch can evaluate to true
independently of the callback pointer.
This can result in calling update_bw_bounding_box() when it is NULL.
Fix this by separating the update condition from the pointer checks and
ensuring the callback, dc->clk_mgr, and bw_params are validated before
use.
Fixes the below:
../dc/hwss/dcn401/dcn401_hwseq.c:367 dcn401_init_hw() error: we previously assumed 'dc->res_pool->funcs->update_bw_bounding_box' could be null (see line 362)
(cherry picked from commit 86117c5ab42f21562fedb0a64bffea3ee5fcd477) |
| In the Linux kernel, the following vulnerability has been resolved:
lib/crypto: chacha: Zeroize permuted_state before it leaves scope
Since the ChaCha permutation is invertible, the local variable
'permuted_state' is sufficient to compute the original 'state', and thus
the key, even after the permutation has been done.
While the kernel is quite inconsistent about zeroizing secrets on the
stack (and some prominent userspace crypto libraries don't bother at all
since it's not guaranteed to work anyway), the kernel does try to do it
as a best practice, especially in cases involving the RNG.
Thus, explicitly zeroize 'permuted_state' before it goes out of scope. |
| In the Linux kernel, the following vulnerability has been resolved:
interconnect: qcom: sm8450: Fix NULL pointer dereference in icc_link_nodes()
The change to dynamic IDs for SM8450 platform interconnects left two links
unconverted, fix it to avoid the NULL pointer dereference in runtime,
when a pointer to a destination interconnect is not valid:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
<...>
Call trace:
icc_link_nodes+0x3c/0x100 (P)
qcom_icc_rpmh_probe+0x1b4/0x528
platform_probe+0x64/0xc0
really_probe+0xc4/0x2a8
__driver_probe_device+0x80/0x140
driver_probe_device+0x48/0x170
__device_attach_driver+0xc0/0x148
bus_for_each_drv+0x88/0xf0
__device_attach+0xb0/0x1c0
device_initial_probe+0x58/0x68
bus_probe_device+0x40/0xb8
deferred_probe_work_func+0x90/0xd0
process_one_work+0x15c/0x3c0
worker_thread+0x2e8/0x400
kthread+0x150/0x208
ret_from_fork+0x10/0x20
Code: 900310f4 911d6294 91008280 94176078 (f94002a0)
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Oops: Fatal exception |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: SMP: force responder MITM requirements before building the pairing response
smp_cmd_pairing_req() currently builds the pairing response from the
initiator auth_req before enforcing the local BT_SECURITY_HIGH
requirement. If the initiator omits SMP_AUTH_MITM, the response can
also omit it even though the local side still requires MITM.
tk_request() then sees an auth value without SMP_AUTH_MITM and may
select JUST_CFM, making method selection inconsistent with the pairing
policy the responder already enforces.
When the local side requires HIGH security, first verify that MITM can
be achieved from the IO capabilities and then force SMP_AUTH_MITM in the
response in both rsp.auth_req and auth. This keeps the responder auth bits
and later method selection aligned. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: reject direct access to nullable PTR_TO_BUF pointers
check_mem_access() matches PTR_TO_BUF via base_type() which strips
PTR_MAYBE_NULL, allowing direct dereference without a null check.
Map iterator ctx->key and ctx->value are PTR_TO_BUF | PTR_MAYBE_NULL.
On stop callbacks these are NULL, causing a kernel NULL dereference.
Add a type_may_be_null() guard to the PTR_TO_BUF branch, matching the
existing PTR_TO_BTF_ID pattern. |
| In the Linux kernel, the following vulnerability has been resolved:
thermal: core: Fix thermal zone device registration error path
If thermal_zone_device_register_with_trips() fails after registering
a thermal zone device, it needs to wait for the tz->removal completion
like thermal_zone_device_unregister(), in case user space has managed
to take a reference to the thermal zone device's kobject, in which case
thermal_release() may not be called by the error path itself and tz may
be freed prematurely.
Add the missing wait_for_completion() call to the thermal zone device
registration error path. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/kexec: Disable KCOV instrumentation after load_segments()
The load_segments() function changes segment registers, invalidating GS base
(which KCOV relies on for per-cpu data). When CONFIG_KCOV is enabled, any
subsequent instrumented C code call (e.g. native_gdt_invalidate()) begins
crashing the kernel in an endless loop.
To reproduce the problem, it's sufficient to do kexec on a KCOV-instrumented
kernel:
$ kexec -l /boot/otherKernel
$ kexec -e
The real-world context for this problem is enabling crash dump collection in
syzkaller. For this, the tool loads a panic kernel before fuzzing and then
calls makedumpfile after the panic. This workflow requires both CONFIG_KEXEC
and CONFIG_KCOV to be enabled simultaneously.
Adding safeguards directly to the KCOV fast-path (__sanitizer_cov_trace_pc())
is also undesirable as it would introduce an extra performance overhead.
Disabling instrumentation for the individual functions would be too fragile,
so disable KCOV instrumentation for the entire machine_kexec_64.c and
physaddr.c. If coverage-guided fuzzing ever needs these components in the
future, other approaches should be considered.
The problem is not relevant for 32 bit kernels as CONFIG_KCOV is not supported
there.
[ bp: Space out comment for better readability. ] |
