| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: aead,cipher - zeroize key buffer after use
I.G 9.7.B for FIPS 140-3 specifies that variables temporarily holding
cryptographic information should be zeroized once they are no longer
needed. Accomplish this by using kfree_sensitive for buffers that
previously held the private key. |
| In the Linux kernel, the following vulnerability has been resolved:
IB/core: Implement a limit on UMAD receive List
The existing behavior of ib_umad, which maintains received MAD
packets in an unbounded list, poses a risk of uncontrolled growth.
As user-space applications extract packets from this list, the rate
of extraction may not match the rate of incoming packets, leading
to potential list overflow.
To address this, we introduce a limit to the size of the list. After
considering typical scenarios, such as OpenSM processing, which can
handle approximately 100k packets per second, and the 1-second retry
timeout for most packets, we set the list size limit to 200k. Packets
received beyond this limit are dropped, assuming they are likely timed
out by the time they are handled by user-space.
Notably, packets queued on the receive list due to reasons like
timed-out sends are preserved even when the list is full. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost_task: Handle SIGKILL by flushing work and exiting
Instead of lingering until the device is closed, this has us handle
SIGKILL by:
1. marking the worker as killed so we no longer try to use it with
new virtqueues and new flush operations.
2. setting the virtqueue to worker mapping so no new works are queued.
3. running all the exiting works. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: avoid overflows in dirty throttling logic
The dirty throttling logic is interspersed with assumptions that dirty
limits in PAGE_SIZE units fit into 32-bit (so that various multiplications
fit into 64-bits). If limits end up being larger, we will hit overflows,
possible divisions by 0 etc. Fix these problems by never allowing so
large dirty limits as they have dubious practical value anyway. For
dirty_bytes / dirty_background_bytes interfaces we can just refuse to set
so large limits. For dirty_ratio / dirty_background_ratio it isn't so
simple as the dirty limit is computed from the amount of available memory
which can change due to memory hotplug etc. So when converting dirty
limits from ratios to numbers of pages, we just don't allow the result to
exceed UINT_MAX.
This is root-only triggerable problem which occurs when the operator
sets dirty limits to >16 TB. |
| In the Linux kernel, the following vulnerability has been resolved:
leds: mlxreg: Use devm_mutex_init() for mutex initialization
In this driver LEDs are registered using devm_led_classdev_register()
so they are automatically unregistered after module's remove() is done.
led_classdev_unregister() calls module's led_set_brightness() to turn off
the LEDs and that callback uses mutex which was destroyed already
in module's remove() so use devm API instead. |
| In the Linux kernel, the following vulnerability has been resolved:
jffs2: Fix potential illegal address access in jffs2_free_inode
During the stress testing of the jffs2 file system,the following
abnormal printouts were found:
[ 2430.649000] Unable to handle kernel paging request at virtual address 0069696969696948
[ 2430.649622] Mem abort info:
[ 2430.649829] ESR = 0x96000004
[ 2430.650115] EC = 0x25: DABT (current EL), IL = 32 bits
[ 2430.650564] SET = 0, FnV = 0
[ 2430.650795] EA = 0, S1PTW = 0
[ 2430.651032] FSC = 0x04: level 0 translation fault
[ 2430.651446] Data abort info:
[ 2430.651683] ISV = 0, ISS = 0x00000004
[ 2430.652001] CM = 0, WnR = 0
[ 2430.652558] [0069696969696948] address between user and kernel address ranges
[ 2430.653265] Internal error: Oops: 96000004 [#1] PREEMPT SMP
[ 2430.654512] CPU: 2 PID: 20919 Comm: cat Not tainted 5.15.25-g512f31242bf6 #33
[ 2430.655008] Hardware name: linux,dummy-virt (DT)
[ 2430.655517] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 2430.656142] pc : kfree+0x78/0x348
[ 2430.656630] lr : jffs2_free_inode+0x24/0x48
[ 2430.657051] sp : ffff800009eebd10
[ 2430.657355] x29: ffff800009eebd10 x28: 0000000000000001 x27: 0000000000000000
[ 2430.658327] x26: ffff000038f09d80 x25: 0080000000000000 x24: ffff800009d38000
[ 2430.658919] x23: 5a5a5a5a5a5a5a5a x22: ffff000038f09d80 x21: ffff8000084f0d14
[ 2430.659434] x20: ffff0000bf9a6ac0 x19: 0169696969696940 x18: 0000000000000000
[ 2430.659969] x17: ffff8000b6506000 x16: ffff800009eec000 x15: 0000000000004000
[ 2430.660637] x14: 0000000000000000 x13: 00000001000820a1 x12: 00000000000d1b19
[ 2430.661345] x11: 0004000800000000 x10: 0000000000000001 x9 : ffff8000084f0d14
[ 2430.662025] x8 : ffff0000bf9a6b40 x7 : ffff0000bf9a6b48 x6 : 0000000003470302
[ 2430.662695] x5 : ffff00002e41dcc0 x4 : ffff0000bf9aa3b0 x3 : 0000000003470342
[ 2430.663486] x2 : 0000000000000000 x1 : ffff8000084f0d14 x0 : fffffc0000000000
[ 2430.664217] Call trace:
[ 2430.664528] kfree+0x78/0x348
[ 2430.664855] jffs2_free_inode+0x24/0x48
[ 2430.665233] i_callback+0x24/0x50
[ 2430.665528] rcu_do_batch+0x1ac/0x448
[ 2430.665892] rcu_core+0x28c/0x3c8
[ 2430.666151] rcu_core_si+0x18/0x28
[ 2430.666473] __do_softirq+0x138/0x3cc
[ 2430.666781] irq_exit+0xf0/0x110
[ 2430.667065] handle_domain_irq+0x6c/0x98
[ 2430.667447] gic_handle_irq+0xac/0xe8
[ 2430.667739] call_on_irq_stack+0x28/0x54
The parameter passed to kfree was 5a5a5a5a, which corresponds to the target field of
the jffs_inode_info structure. It was found that all variables in the jffs_inode_info
structure were 5a5a5a5a, except for the first member sem. It is suspected that these
variables are not initialized because they were set to 5a5a5a5a during memory testing,
which is meant to detect uninitialized memory.The sem variable is initialized in the
function jffs2_i_init_once, while other members are initialized in
the function jffs2_init_inode_info.
The function jffs2_init_inode_info is called after iget_locked,
but in the iget_locked function, the destroy_inode process is triggered,
which releases the inode and consequently, the target member of the inode
is not initialized.In concurrent high pressure scenarios, iget_locked
may enter the destroy_inode branch as described in the code.
Since the destroy_inode functionality of jffs2 only releases the target,
the fix method is to set target to NULL in jffs2_i_init_once. |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: fix inode number range checks
Patch series "nilfs2: fix potential issues related to reserved inodes".
This series fixes one use-after-free issue reported by syzbot, caused by
nilfs2's internal inode being exposed in the namespace on a corrupted
filesystem, and a couple of flaws that cause problems if the starting
number of non-reserved inodes written in the on-disk super block is
intentionally (or corruptly) changed from its default value.
This patch (of 3):
In the current implementation of nilfs2, "nilfs->ns_first_ino", which
gives the first non-reserved inode number, is read from the superblock,
but its lower limit is not checked.
As a result, if a number that overlaps with the inode number range of
reserved inodes such as the root directory or metadata files is set in the
super block parameter, the inode number test macros (NILFS_MDT_INODE and
NILFS_VALID_INODE) will not function properly.
In addition, these test macros use left bit-shift calculations using with
the inode number as the shift count via the BIT macro, but the result of a
shift calculation that exceeds the bit width of an integer is undefined in
the C specification, so if "ns_first_ino" is set to a large value other
than the default value NILFS_USER_INO (=11), the macros may potentially
malfunction depending on the environment.
Fix these issues by checking the lower bound of "nilfs->ns_first_ino" and
by preventing bit shifts equal to or greater than the NILFS_USER_INO
constant in the inode number test macros.
Also, change the type of "ns_first_ino" from signed integer to unsigned
integer to avoid the need for type casting in comparisons such as the
lower bound check introduced this time. |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: add missing check for inode numbers on directory entries
Syzbot reported that mounting and unmounting a specific pattern of
corrupted nilfs2 filesystem images causes a use-after-free of metadata
file inodes, which triggers a kernel bug in lru_add_fn().
As Jan Kara pointed out, this is because the link count of a metadata file
gets corrupted to 0, and nilfs_evict_inode(), which is called from iput(),
tries to delete that inode (ifile inode in this case).
The inconsistency occurs because directories containing the inode numbers
of these metadata files that should not be visible in the namespace are
read without checking.
Fix this issue by treating the inode numbers of these internal files as
errors in the sanity check helper when reading directory folios/pages.
Also thanks to Hillf Danton and Matthew Wilcox for their initial mm-layer
analysis. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ecdh - explicitly zeroize private_key
private_key is overwritten with the key parameter passed in by the
caller (if present), or alternatively a newly generated private key.
However, it is possible that the caller provides a key (or the newly
generated key) which is shorter than the previous key. In that
scenario, some key material from the previous key would not be
overwritten. The easiest solution is to explicitly zeroize the entire
private_key array first.
Note that this patch slightly changes the behavior of this function:
previously, if the ecc_gen_privkey failed, the old private_key would
remain. Now, the private_key is always zeroized. This behavior is
consistent with the case where params.key is set and ecc_is_key_valid
fails. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: emux: improve patch ioctl data validation
In load_data(), make the validation of and skipping over the main info
block match that in load_guspatch().
In load_guspatch(), add checking that the specified patch length matches
the actually supplied data, like load_data() already did. |
| In the Linux kernel, the following vulnerability has been resolved:
net/iucv: Avoid explicit cpumask var allocation on stack
For CONFIG_CPUMASK_OFFSTACK=y kernel, explicit allocation of cpumask
variable on stack is not recommended since it can cause potential stack
overflow.
Instead, kernel code should always use *cpumask_var API(s) to allocate
cpumask var in config-neutral way, leaving allocation strategy to
CONFIG_CPUMASK_OFFSTACK.
Use *cpumask_var API(s) to address it. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/panel: ilitek-ili9881c: Fix warning with GPIO controllers that sleep
The ilitek-ili9881c controls the reset GPIO using the non-sleeping
gpiod_set_value() function. This complains loudly when the GPIO
controller needs to sleep. As the caller can sleep, use
gpiod_set_value_cansleep() to fix the issue. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/restrack: Fix potential invalid address access
struct rdma_restrack_entry's kern_name was set to KBUILD_MODNAME
in ib_create_cq(), while if the module exited but forgot del this
rdma_restrack_entry, it would cause a invalid address access in
rdma_restrack_clean() when print the owner of this rdma_restrack_entry.
These code is used to help find one forgotten PD release in one of the
ULPs. But it is not needed anymore, so delete them. |
| In the Linux kernel, the following vulnerability has been resolved:
gfs2: Fix NULL pointer dereference in gfs2_log_flush
In gfs2_jindex_free(), set sdp->sd_jdesc to NULL under the log flush
lock to provide exclusion against gfs2_log_flush().
In gfs2_log_flush(), check if sdp->sd_jdesc is non-NULL before
dereferencing it. Otherwise, we could run into a NULL pointer
dereference when outstanding glock work races with an unmount
(glock_work_func -> run_queue -> do_xmote -> inode_go_sync ->
gfs2_log_flush). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Take return from set_memory_ro() into account with bpf_prog_lock_ro()
set_memory_ro() can fail, leaving memory unprotected.
Check its return and take it into account as an error. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Take return from set_memory_rox() into account with bpf_jit_binary_lock_ro()
set_memory_rox() can fail, leaving memory unprotected.
Check return and bail out when bpf_jit_binary_lock_ro() returns
an error. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Mark bpf prog stack with kmsan_unposion_memory in interpreter mode
syzbot reported uninit memory usages during map_{lookup,delete}_elem.
==========
BUG: KMSAN: uninit-value in __dev_map_lookup_elem kernel/bpf/devmap.c:441 [inline]
BUG: KMSAN: uninit-value in dev_map_lookup_elem+0xf3/0x170 kernel/bpf/devmap.c:796
__dev_map_lookup_elem kernel/bpf/devmap.c:441 [inline]
dev_map_lookup_elem+0xf3/0x170 kernel/bpf/devmap.c:796
____bpf_map_lookup_elem kernel/bpf/helpers.c:42 [inline]
bpf_map_lookup_elem+0x5c/0x80 kernel/bpf/helpers.c:38
___bpf_prog_run+0x13fe/0xe0f0 kernel/bpf/core.c:1997
__bpf_prog_run256+0xb5/0xe0 kernel/bpf/core.c:2237
==========
The reproducer should be in the interpreter mode.
The C reproducer is trying to run the following bpf prog:
0: (18) r0 = 0x0
2: (18) r1 = map[id:49]
4: (b7) r8 = 16777216
5: (7b) *(u64 *)(r10 -8) = r8
6: (bf) r2 = r10
7: (07) r2 += -229
^^^^^^^^^^
8: (b7) r3 = 8
9: (b7) r4 = 0
10: (85) call dev_map_lookup_elem#1543472
11: (95) exit
It is due to the "void *key" (r2) passed to the helper. bpf allows uninit
stack memory access for bpf prog with the right privileges. This patch
uses kmsan_unpoison_memory() to mark the stack as initialized.
This should address different syzbot reports on the uninit "void *key"
argument during map_{lookup,delete}_elem. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/nouveau/dispnv04: fix null pointer dereference in nv17_tv_get_ld_modes
In nv17_tv_get_ld_modes(), the return value of drm_mode_duplicate() is
assigned to mode, which will lead to a possible NULL pointer dereference
on failure of drm_mode_duplicate(). Add a check to avoid npd. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Fix NULL pointer dereference in 'ni_write_inode'
Syzbot found the following issue:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000016
Mem abort info:
ESR = 0x0000000096000006
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x06: level 2 translation fault
Data abort info:
ISV = 0, ISS = 0x00000006
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=000000010af56000
[0000000000000016] pgd=08000001090da003, p4d=08000001090da003, pud=08000001090ce003, pmd=0000000000000000
Internal error: Oops: 0000000096000006 [#1] PREEMPT SMP
Modules linked in:
CPU: 1 PID: 3036 Comm: syz-executor206 Not tainted 6.0.0-rc6-syzkaller-17739-g16c9f284e746 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/26/2022
pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : is_rec_inuse fs/ntfs3/ntfs.h:313 [inline]
pc : ni_write_inode+0xac/0x798 fs/ntfs3/frecord.c:3232
lr : ni_write_inode+0xa0/0x798 fs/ntfs3/frecord.c:3226
sp : ffff8000126c3800
x29: ffff8000126c3860 x28: 0000000000000000 x27: ffff0000c8b02000
x26: ffff0000c7502320 x25: ffff0000c7502288 x24: 0000000000000000
x23: ffff80000cbec91c x22: ffff0000c8b03000 x21: ffff0000c8b02000
x20: 0000000000000001 x19: ffff0000c75024d8 x18: 00000000000000c0
x17: ffff80000dd1b198 x16: ffff80000db59158 x15: ffff0000c4b6b500
x14: 00000000000000b8 x13: 0000000000000000 x12: ffff0000c4b6b500
x11: ff80800008be1b60 x10: 0000000000000000 x9 : ffff0000c4b6b500
x8 : 0000000000000000 x7 : ffff800008be1b50 x6 : 0000000000000000
x5 : 0000000000000000 x4 : 0000000000000001 x3 : 0000000000000000
x2 : 0000000000000008 x1 : 0000000000000001 x0 : 0000000000000000
Call trace:
is_rec_inuse fs/ntfs3/ntfs.h:313 [inline]
ni_write_inode+0xac/0x798 fs/ntfs3/frecord.c:3232
ntfs_evict_inode+0x54/0x84 fs/ntfs3/inode.c:1744
evict+0xec/0x334 fs/inode.c:665
iput_final fs/inode.c:1748 [inline]
iput+0x2c4/0x324 fs/inode.c:1774
ntfs_new_inode+0x7c/0xe0 fs/ntfs3/fsntfs.c:1660
ntfs_create_inode+0x20c/0xe78 fs/ntfs3/inode.c:1278
ntfs_create+0x54/0x74 fs/ntfs3/namei.c:100
lookup_open fs/namei.c:3413 [inline]
open_last_lookups fs/namei.c:3481 [inline]
path_openat+0x804/0x11c4 fs/namei.c:3688
do_filp_open+0xdc/0x1b8 fs/namei.c:3718
do_sys_openat2+0xb8/0x22c fs/open.c:1311
do_sys_open fs/open.c:1327 [inline]
__do_sys_openat fs/open.c:1343 [inline]
__se_sys_openat fs/open.c:1338 [inline]
__arm64_sys_openat+0xb0/0xe0 fs/open.c:1338
__invoke_syscall arch/arm64/kernel/syscall.c:38 [inline]
invoke_syscall arch/arm64/kernel/syscall.c:52 [inline]
el0_svc_common+0x138/0x220 arch/arm64/kernel/syscall.c:142
do_el0_svc+0x48/0x164 arch/arm64/kernel/syscall.c:206
el0_svc+0x58/0x150 arch/arm64/kernel/entry-common.c:636
el0t_64_sync_handler+0x84/0xf0 arch/arm64/kernel/entry-common.c:654
el0t_64_sync+0x18c/0x190
Code: 97dafee4 340001b4 f9401328 2a1f03e0 (79402d14)
---[ end trace 0000000000000000 ]---
Above issue may happens as follows:
ntfs_new_inode
mi_init
mi->mrec = kmalloc(sbi->record_size, GFP_NOFS); -->failed to allocate memory
if (!mi->mrec)
return -ENOMEM;
iput
iput_final
evict
ntfs_evict_inode
ni_write_inode
is_rec_inuse(ni->mi.mrec)-> As 'ni->mi.mrec' is NULL trigger NULL-ptr-deref
To solve above issue if new inode failed make inode bad before call 'iput()' in
'ntfs_new_inode()'. |
| In the Linux kernel, the following vulnerability has been resolved:
exfat: use kvmalloc_array/kvfree instead of kmalloc_array/kfree
The call stack shown below is a scenario in the Linux 4.19 kernel.
Allocating memory failed where exfat fs use kmalloc_array due to
system memory fragmentation, while the u-disk was inserted without
recognition.
Devices such as u-disk using the exfat file system are pluggable and
may be insert into the system at any time.
However, long-term running systems cannot guarantee the continuity of
physical memory. Therefore, it's necessary to address this issue.
Binder:2632_6: page allocation failure: order:4,
mode:0x6040c0(GFP_KERNEL|__GFP_COMP), nodemask=(null)
Call trace:
[242178.097582] dump_backtrace+0x0/0x4
[242178.097589] dump_stack+0xf4/0x134
[242178.097598] warn_alloc+0xd8/0x144
[242178.097603] __alloc_pages_nodemask+0x1364/0x1384
[242178.097608] kmalloc_order+0x2c/0x510
[242178.097612] kmalloc_order_trace+0x40/0x16c
[242178.097618] __kmalloc+0x360/0x408
[242178.097624] load_alloc_bitmap+0x160/0x284
[242178.097628] exfat_fill_super+0xa3c/0xe7c
[242178.097635] mount_bdev+0x2e8/0x3a0
[242178.097638] exfat_fs_mount+0x40/0x50
[242178.097643] mount_fs+0x138/0x2e8
[242178.097649] vfs_kern_mount+0x90/0x270
[242178.097655] do_mount+0x798/0x173c
[242178.097659] ksys_mount+0x114/0x1ac
[242178.097665] __arm64_sys_mount+0x24/0x34
[242178.097671] el0_svc_common+0xb8/0x1b8
[242178.097676] el0_svc_handler+0x74/0x90
[242178.097681] el0_svc+0x8/0x340
By analyzing the exfat code,we found that continuous physical memory
is not required here,so kvmalloc_array is used can solve this problem. |
