| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| JupyterLab versions >=4.6.0,<=4.6.1 and <=4.5.9 contain an allowlist/blocklist enforcement gap in PyPIExtensionManager.install(). A missing 'await' caused the is_install_allowed coroutine to never execute, so the extension allowlist/blocklist check was not enforced for direct callers of install(). The stock JupyterLab HTTP API and Extension Manager UI are not affected, as they perform a separate, correctly awaited check. The issue affects only deployments where a custom extension or downstream integration imports PyPIExtensionManager and calls install() directly with a package name influenced by untrusted input, an allowlist/blocklist is configured, the PyPI Extension Manager is enabled, and kernels and terminals are disabled or delegated to remote hosts. Fixed in JupyterLab 4.6.2 and 4.5.10. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: spacemit: fix NULL check in spacemit_pin_set_config
spacemit_pin_set_config() looks up the per-pin descriptor with
spacemit_get_pin() then checks the wrong variable for failure:
const struct spacemit_pin *spin = spacemit_get_pin(pctrl, pin);
...
if (!pin)
return -EINVAL;
reg = spacemit_pin_to_reg(pctrl, spin->pin);
pin is an unsigned int pin id, where 0 (GPIO_0 / gmac0_rxdv on K3) is a
valid pin, so rejecting it here drops the PAD config write for the first
pin of every group. On K3 Pico-ITX the GMAC RGMII group lists pin 0 as
its first entry, so its drive-strength / bias configuration was silently
ignored.
The intended guard is against spacemit_get_pin() returning NULL when the
pin id isn't in the SoC's pin table. Check spin instead, which both
restores PAD setup for pin 0 and prevents a NULL deref on spin->pin. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: enforce cursor size limits for MOB cursors
vmw_cursor_plane_atomic_check() bounds cursor width and height only
on the legacy update path; the SVGA_CAP2_CURSOR_MOB path -- the
default on modern hosts -- accepts any size. When the requested size
exceeds SVGA_REG_CURSOR_MAX_DIMENSION or SVGA_REG_MOB_MAX_SIZE,
vmw_cursor_mob_get() returns -EINVAL and leaves vps->cursor.mob NULL.
Its return value is then discarded in vmw_cursor_plane_prepare_fb(),
so the subsequent vmw_cursor_update_mob() calls
vmw_bo_map_and_cache(NULL) and oopses inside
vmw_bo_map_and_cache_size() on the tbo.base.size load.
Reachable from any DRM master via DRM_IOCTL_MODE_CURSOR2 with a
sufficiently large width or height (e.g. cursor_max_dim + 1).
Reject oversized cursors in atomic_check for both MOB-backed cursor
update types. The MOB byte-size limit only applies to the
SVGA_CAP2_CURSOR_MOB path (vmw_cursor_mob_size() returns 0 for
GB_ONLY); compute the required MOB size in 64-bit to avoid overflow
when very large dimensions are requested.
In prepare_fb only call vmw_cursor_mob_get()/_map() for
VMW_CURSOR_UPDATE_MOB -- the GB_ONLY path uses bo->map.virtual
directly and would otherwise be silently downgraded to NONE on hosts
without SVGA_CAP2_CURSOR_MOB (where vmw_cursor_mob_get() always
returns -EINVAL). Degrade the update to NONE if vmw_cursor_mob_get()
or vmw_cursor_mob_map() fails so the update path does not run with a
NULL backing MOB. |
| In Zimbra Collaboration (ZCS) before 10.1.17, a Cross-Site Request Forgery (CSRF) vulnerability exists in the Exchange Web Services (EWS) endpoint of Zimbra Collaboration (ZCS) due to insufficient validation of request content types. An attacker can exploit this vulnerability by causing an authenticated user to submit a crafted request, potentially allowing unauthorized actions to be performed on behalf of the victim. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - Treat zero-length cert chain as query for blob lengths
When handling a PDH export, treat a zero-length userspace cert chain buffer
as a request to query the length of the relevant blobs. Failure to account
for the zero-length buffer trips a BUG_ON() when running with
CONFIG_DEBUG_VIRTUAL=y due to trying to get the physical address of the
ZERO_SIZE_PTR (returned by kzalloc() on the bogus allocation).
kernel BUG at arch/x86/mm/physaddr.c:28 !
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 30 UID: 0 PID: 28580 Comm: syz.2.18 Kdump: loaded
Tainted: G W 6.18.16-smp-DEV #1 NONE
Tainted: [W]=WARN
Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 12.62.0-0 11/19/2025
RIP: 0010:__phys_addr+0x16a/0x180 arch/x86/mm/physaddr.c:28
RSP: 0018:ffffc9008329fc80 EFLAGS: 00010293
RAX: ffffffff8179110a RBX: 0000778000000010 RCX: ffff8884e6992600
RDX: 0000000000000000 RSI: 0000000080000010 RDI: 0000778000000010
RBP: ffffc9008329fdf0 R08: 0000000000000dc0 R09: 00000000ffffffff
R10: dffffc0000000000 R11: fffffbfff126d297 R12: dffffc0000000000
R13: 1ffff92010653fc8 R14: 0000000080000010 R15: dffffc0000000000
FS: 0000555556bec9c0(0000) GS:ffff88aa4ce1c000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd3159e7000 CR3: 00000004fbc44000 CR4: 0000000000350ef0
Call Trace:
<TASK>
[<ffffffff853d3869>] sev_ioctl_do_pdh_export+0x559/0x7a0 drivers/crypto/ccp/sev-dev.c:2308
[<ffffffff853d1fdd>] sev_ioctl+0x2cd/0x480 drivers/crypto/ccp/sev-dev.c:2556
[<ffffffff82549ebc>] vfs_ioctl fs/ioctl.c:52 [inline]
[<ffffffff82549ebc>] __do_sys_ioctl fs/ioctl.c:598 [inline]
[<ffffffff82549ebc>] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:584
[<ffffffff8630115f>] do_syscall_x64 arch/x86/entry/syscall_64.c:64 [inline]
[<ffffffff8630115f>] do_syscall_64+0x9f/0xf40 arch/x86/entry/syscall_64.c:98
[<ffffffff81000136>] entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7fd3158eac39
</TASK>
Thankfully, the bug is benign outside of CONFIG_DEBUG_VIRTUAL=y as getting
the physical address is just arithmetic, and the PSP errors out before
trying to write to the garbage address (which it must, otherwise querying
the blob lengths would clobber memory at pfn=0). |
| In the Linux kernel, the following vulnerability has been resolved:
soc: xilinx: Shutdown and free rx mailbox channel
A mbox rx channel is requested using mbox_request_channel_byname() in
probe. In remove callback, the rx mailbox channel is cleaned up when the
rx_chan is NULL due to incorrect condition check. The mailbox channel is
not shutdown and it can receive messages even after the device removal.
This leads to use after free. Also the channel resources are not freed.
Fix this by checking the rx_chan correctly. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (sht3x) Fix unaligned accesses
Sashiko reports:
In sht3x_update_client(), the 16-bit temperature and humidity values are
extracted from a stack-allocated byte array using be16_to_cpup(). The
pointers passed to this function are calculated as buf and buf + 3. Since
the difference between the two pointers is an odd number of bytes, at
least one of them is guaranteed to be at an unaligned offset.
This will trigger an alignment fault on strict-alignment architectures
such as ARMv5 or SPARC, resulting in a kernel panic.
Fix the problem by using get_unaligned_be16() instead of be16_to_cpup(),
and put_unaligned_be16() instead of cpu_to_be16(). |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: vgic: Avoid double-deactivate of IRQs in the nested context
In the nested state, the physical interrupt has already been
deactivated through the HW bit in the LR. The extra deactivation
would be harmless but can hit an errata case on AmpereOne, so
avoid it here.
On AmpereOne, deactivating a physical interrupt through
ICC_DIR_EL1 or ICC_EOIR1_EL1 (depending on EOImode) which is not
active, but is the highest priority pending interrupt causes the
cpu to lose the interrupt pending state and also prevents the
delivery of future interrupts. |
| In Zimbra Collaboration (ZCS) before 10.1.17, weak cryptographic key generation vulnerability exists in the OnlyOffice integration. The zimbraDocumentEditingJwtSecret is generated using an insecure random number generator, resulting in insufficient entropy. An attacker who obtains a JWT signed with the generated secret may be able to recover the JWT signing secret through offline brute-force, potentially enabling JWT forgery. |
| This CVE ID was assigned to a reported vulnerability in the Customer Reviews for WooCommerce WordPress plugin and was never published. The report was withdrawn: the precondition it depends on, an attacker obtaining a review form identifier belonging to a customer they do not already have access to, could not be demonstrated. No advisory was issued for this ID. |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd/viommu: Release the igroup lock on the vdevice_size error path
iommufd_vdevice_alloc_ioctl() takes idev->igroup->lock, then validates the
driver's vdevice_size against the core structure size with a WARN_ON_ONCE.
On failure that guard jumps to out_put_idev, below out_unlock_igroup, so it
skips the mutex_unlock(), leaving the igroup lock held and deadlocking the
next vDEVICE operation on that group.
Jump to out_unlock_igroup instead. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (occ) unregister sysfs devices outside occ lock
occ_active(false) and occ_shutdown() unregister sysfs-backed devices while
occ->lock is held. hwmon_device_unregister() and sysfs_remove_group() can
wait for active sysfs callbacks to drain, and those callbacks can enter the
OCC update path and try to take occ->lock again. That gives the unregister
paths the lock ordering occ->lock -> sysfs callback drain, while a callback
has the opposite edge sysfs callback -> occ->lock.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the real unregister and callback carrier:
occ_shutdown()
hwmon_device_unregister()
occ_show_temp_1()
occ_update_response()
Lockdep reported the circular dependency with occ_shutdown() already
holding the OCC mutex and hwmon_device_unregister() waiting on the sysfs
side:
WARNING: possible circular locking dependency detected
... (sysfs_lock) ... at: hwmon_device_unregister+0x12/0x30 [vuln_msv]
... (&test_occ.lock) ... at: occ_shutdown.constprop.0+0xe/0x40 [vuln_msv]
occ_update_response.isra.0+0xb/0x20 [vuln_msv]
occ_show_temp_1.constprop.0.isra.0+0x23/0x40 [vuln_msv]
*** DEADLOCK ***
Serialize hwmon registration and removal with a separate hwmon_lock.
Under that lock, detach occ->hwmon and update occ->active while occ->lock
is held so concurrent OCC state changes still see a stable state, then
drop occ->lock before calling hwmon_device_unregister(). Remove the
driver sysfs group before taking occ->lock in occ_shutdown(), so draining
the driver attributes cannot wait while the OCC mutex is held. Also make
OCC update callbacks return -ENODEV after deactivation, so callbacks that
already passed sysfs active protection do not poll the hardware after
teardown has detached the hwmon device. |
| The User Frontend WordPress plugin before 4.3.10 does not properly validate field type definitions and deserialises user-controlled post metadata when rendering submitted posts, allowing users with Editor-level access and above to inject arbitrary PHP objects, which can lead to remote code execution when a suitable POP chain is present on the site. |
| The Quiz and Survey Master (QSM) WordPress plugin before 11.2.4 does not check authorisation when returning question bank entries through one of its REST API routes, allowing users with a role as low as Contributor to read the questions, hints and correct answer keys of quizzes belonging to other users. |
| The User Registration & Membership WordPress plugin before 5.2.5 does not verify that the account whose pending email change is being cancelled belongs to the user making the request, allowing authenticated users with Subscriber-level access and above to cancel any other user's in-progress email change, including an administrator's. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: migrate_device: fix pte_pfn/pte_dirty called on non-present PTE
pte_pfn() and pte_dirty() have undefined behaviour when called on a
non-present PTE. In migrate_vma_collect_pmd(), these functions may be
invoked on non-present entries (e.g., device-private entries), leading
to potential crashes from pte_pfn() or incorrect dirty folio accounting
from pte_dirty(). Fix both by guarding with pte_present() checks. |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: drop __init from vec_check_unaligned_access_speed_all_cpus
This function runs within a kthread and need not necessarily finish
before system finishes boot and free_initmem() unmaps the .init.text
section. This function makes calls to SBI for probing unaligned access
speed, and if this is slow for some reason (say some debug prints were
added to SBI), the kthread can still be running at this point and result
in an instruction page fault when trying to fetch from the freed region.
[ 25.642087] Unable to handle kernel paging request at virtual address ffffffff80a04ef8
[ 25.646694] Current vec_check_unali pgtable: 4K pagesize, 48-bit VAs, pgdp=0x00004000316e9000
[ 25.653170] [ffffffff80a04ef8] pgd=000010004be7e401, p4d=000010004be7e401, pud=000010004be7e001, pmd=000010000c3000e3
[ 25.661244] Oops [#1]
[ 25.662997] Modules linked in:
[ 25.665357] CPU: 3 UID: 0 PID: 42 Comm: vec_check_unali Not tainted 7.0.0-tt-blackhole-asrinivasan-00007-g30ff73f18211 #570 PREEMPTLAZY
[ 25.674669] Hardware name: Tenstorrent Blackhole (DT)
[ 25.678545] epc : vec_check_unaligned_access_speed_all_cpus+0x18/0x2c
[ 25.683458] ra : vec_check_unaligned_access_speed_all_cpus+0x18/0x2c
[ 25.688372] epc : ffffffff80a04ef8 ra : ffffffff80a04ef8 sp : ffff8f8000203e20
[ 25.693874] gp : ffffffff814dc168 tp : ffffaf8001ad9900 t0 : 0000000000000000
[ 25.699401] t1 : fffffffffffffff0 t2 : ffffaf8001ad9a10 s0 : ffff8f8000203e30
[ 25.704912] s1 : ffffaf80018dc780 a0 : 0000000000000000 a1 : 0000000000000002
[ 25.710407] a2 : 00000000000001f0 a3 : 0000000000000018 a4 : 0000000000000000
[ 25.715917] a5 : 0000000000000000 a6 : ffffaf8001c03d98 a7 : ffffaf8001c03e30
[ 25.721419] s2 : ffff8f8000023c98 s3 : ffffaf8001aa1240 s4 : ffffffff80a04ee0
[ 25.726937] s5 : 0000000000000000 s6 : 0000000000000000 s7 : 0000000000000000
[ 25.732450] s8 : 0000000000000000 s9 : 0000000000000000 s10: 0000000000000000
[ 25.737944] s11: 0000000000000000 t3 : 0000000000000002 t4 : 0000000000000402
[ 25.743481] t5 : 0000000000000040 t6 : 0000000000000004 ssp : 0000000000000000
[ 25.749024] status: 0000000200000120 badaddr: ffffffff80a04ef8 cause: 000000000000000c
[ 25.755060] [<ffffffff80a04ef8>] vec_check_unaligned_access_speed_all_cpus+0x18/0x2c
[ 25.760964] [<ffffffff80047a10>] kthread+0xd8/0xfc
[ 25.764660] [<ffffffff80010c48>] ret_from_fork_kernel+0x18/0x1c4
[ 25.769220] [<ffffffff80895fe6>] ret_from_fork_kernel_asm+0x16/0x18
[ 25.774018] Code: cccc cccc cccc cccc cccc cccc cccc cccc cccc cccc (cccc) cccc
Drop __init from its signature so that this doesn't happen. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing/mmiotrace: Add NULL check for mmio_trace_array in logging functions
mmio_trace_rw() and mmio_trace_mapping() retrieve mmio_trace_array into
tr and pass it to __trace_mmiotrace_rw() and __trace_mmiotrace_map().
If these functions are invoked while mmio_trace_array is NULL (e.g. before
initialization or after disabled), accessing tr->array_buffer.buffer will
result in a NULL pointer dereference crash.
Fix this by adding an explicit NULL check for tr at the beginning of
__trace_mmiotrace_rw() and __trace_mmiotrace_map(). |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: account for fraggap on the paged allocation path
In __ip6_append_data(), when the paged-allocation branch is taken
(MSG_MORE / NETIF_F_SG / large fraglen), alloclen and pagedlen are
computed as
alloclen = fragheaderlen + transhdrlen;
pagedlen = datalen - transhdrlen;
datalen already includes fraggap (datalen = length + fraggap). When
fraggap is non-zero, this is not the first skb and transhdrlen is zero.
The fraggap bytes carried over from the previous skb are copied just past
the fragment headers in the new skb's linear area. The linear area is
therefore undersized by fraggap bytes while pagedlen is overstated by the
same amount, and the copy writes past skb->end into the trailing
skb_shared_info.
An unprivileged user can trigger this via a UDPv6 socket using
MSG_MORE together with MSG_SPLICE_PAGES.
The bad accounting was introduced by commit 773ba4fe9104 ("ipv6:
avoid partial copy for zc"). Before commit ce650a166335 ("udp6: Fix
__ip6_append_data()'s handling of MSG_SPLICE_PAGES"), the negative
copy value caused -EINVAL to be returned. That later commit allowed
MSG_SPLICE_PAGES to proceed in this case, making the corruption
triggerable.
The non-paged branch sets alloclen to fraglen, which already accounts
for fraggap because datalen does. Bring the paged branch in line by
adding fraggap to alloclen and subtracting it from pagedlen.
After this adjustment, copy no longer collapses to -fraggap on the
paged path, so remove the stale comment describing that old arithmetic.
Since a negative copy is no longer expected for a valid MSG_SPLICE_PAGES
case, remove the MSG_SPLICE_PAGES exception from the negative copy check. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: Fix NULL pointer dereference in mt7996_init_tx_queues()
When MT76_NPU and CONFIG_NET_MEDIATEK_SOC_WED are enabled and
mt76 detects properly the Airoha NPU SoC, mt7996_init_tx_queues() will
dereference a NULL WED pointer.
Fix the issue by always passing the WED pointer from mt7996_dma_init(). |
