| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/dp/mst: fix OOB reads on 2-byte fields in sideband reply parsers
Three sideband reply parsers read 16-bit fields as:
val = (raw->msg[idx] << 8) | (raw->msg[idx+1]);
and check bounds only after the fact. When idx == raw->curlen,
raw->msg[idx+1] reads one byte past the received message data into
the following struct fields (curchunk_len, curchunk_idx, curlen).
Affected functions:
- drm_dp_sideband_parse_enum_path_resources_ack()
full_payload_bw_number and avail_payload_bw_number fields
- drm_dp_sideband_parse_allocate_payload_ack()
allocated_pbn field
- drm_dp_sideband_parse_query_payload_ack()
allocated_pbn field
Fix by using a single combined check (idx + 2 > curlen) before each
2-byte read. Since the check is strictly tighter than idx > curlen,
no separate step is needed.
[added fixes tag] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915/bios: range check LFP Data Block panel_type2
While the panel_type from LFP Data Block is range checked, panel_type2
is not. Add a few helpers for range checking, and use them to not only
check panel_type2, but also improve clarity and correctness in the panel
type selection.
Discovered using AI-assisted static analysis confirmed by Intel Product
Security.
v2:
- Fix commit message typo (Michał)
- Add is_panel_type_pnp() (Ville)
(cherry picked from commit c9ebe5d2f25729d6cfbbb1235d640bf67f9275df) |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB reads in rtw_get_wps_ie()
rtw_get_wps_ie() iterates over IE data from network frames without
validating that the IE header and payload fit within the remaining
buffer before reading them. Specifically:
- in_ie[cnt + 1] is read without checking cnt + 1 < in_len
- memcmp(&in_ie[cnt + 2], ...) accesses cnt + 2 without bounds check
- in_ie[cnt + 1] is used as length without verifying payload fits
Add bounds checks at the top of the loop body to break early if fewer
than 2 bytes remain for the IE header, or if the declared payload
extends past the end of the buffer. Also require at least 4 bytes of
payload before comparing the WPS OUI. |
| In the Linux kernel, the following vulnerability has been resolved:
exec: fix unsigned loop counter wrap in transfer_args_to_stack()
The stop value is derived from bprm->p >> PAGE_SHIFT. The index variable
is an unsigned long. If bprm->p drops below PAGE_SIZE and stop becomes
zero the loop condition index >= stop is always true.
After the index == 0 iteration the decrement wraps to ULONG_MAX and
bprm->page[ULONG_MAX] reads sizeof(void *) bytes in front of the array.
The pointer has wrapped to -1. That garbage pointer is then passed to
kmap_local_page() and PAGE_SIZE bytes are copied from wherever that
lands into the stack of the process being created. And the loop doesn't
terminate either...
Getting there only requires bprm->p < PAGE_SIZE. On !MMU
bprm_set_stack_limit() and bprm_hit_stack_limit() are empty. So the only
constraint on how far bprm->p is pushed down is valid_arg_len(), i.e.
that each individual string still fits in what is left.
bprm->p starts at PAGE_SIZE * MAX_ARG_PAGES - sizeof(void *) so a
single argument or environment string of a little over 31 pages leaves
it in the first page:
Oops - load access fault [#1]
CPU: 0 UID: 0 PID: 1 Comm: victim Not tainted 7.2.0-rc4 #1
epc : __memcpy+0xd4/0xf8
ra : transfer_args_to_stack+0xaa/0xae
s4 : ffffffffffffffff s2 : 0000000000000000
a1 : ffffffdc98000000 a2 : 0000000000001000
status: 0000000a00001880 badaddr: ffffffdc98000000 cause: 0000000000000005
[<801a5324>] __memcpy+0xd4/0xf8
[<800d5f6a>] load_flat_binary+0x43a/0x65e
[<800a2de4>] bprm_execve+0x1d4/0x316
[<800a351a>] do_execveat_common+0x12e/0x138
[<800a3d44>] __riscv_sys_execve+0x38/0x4e
Kernel panic - not syncing: Fatal exception in interrupt
This is an arcane bug but we should still fix it.
Count down from MAX_ARG_PAGES so the loop ends when index reaches stop,
stop == 0 included. The iterations performed are unchanged for every
other value of stop.
Only CONFIG_MMU=n builds are affected, transfer_args_to_stack() is used
by binfmt_flat and binfmt_elf_fdpic on nommu only.
The loop predates git history. commit 7e7ec6a93434
("elf_fdpic_transfer_args_to_stack(): make it generic") only moved it
from binfmt_elf_fdpic.c into fs/exec.c and narrowed the copy to the used
part of the first page. The condition and the decrement are unchanged
from 2.6.12-rc2. |
| In the Linux kernel, the following vulnerability has been resolved:
cdrom: fix stack out-of-bounds read in CDROMVOLCTRL
mmc_ioctl_cdrom_volume() first reads the audio control mode page into a
32-byte stack buffer with cgc->buflen set to 24. If the device reports a
block descriptor, the function increases cgc->buflen to include that
descriptor and reads the page again.
For CDROMVOLCTRL, the function then builds a MODE SELECT parameter list
by moving cgc->buffer forward by offset - 8 bytes. This drops the block
descriptor from the outgoing payload and leaves a new 8-byte mode
parameter header in front of the audio control page. However, cgc->buflen
is left unchanged.
With a standard 8-byte block descriptor, cgc->buffer points at buffer + 8
but cgc->buflen remains 32. cdrom_mode_select() therefore asks the low
level packet path to write 32 bytes from that adjusted pointer, reading 8
bytes past the end of the 32-byte stack buffer.
This is not hit by CDROMVOLREAD, and CDROMVOLCTRL only triggers it on
drives that return a non-zero block descriptor length, which helps explain
why it has gone unnoticed. The overread is also sent to the device as
extra MODE SELECT payload, so it may not produce an obvious local failure.
Reduce cgc->buflen by the same amount as the buffer pointer adjustment so
the MODE SELECT transfer covers only the intended parameter list. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix heap buffer overflow in rtw_cfg80211_set_wpa_ie()
supplicant_ie is a 256-byte array in struct security_priv. The WPA and
WPA2 IE copy paths use:
memcpy(padapter->securitypriv.supplicant_ie, &pwpa[0], wpa_ielen + 2);
where wpa_ielen is the raw IE length field (u8, 0-255). When a local user
supplies a connect request via nl80211 with a crafted WPA IE of length 255,
wpa_ielen + 2 equals 257, overflowing the 256-byte buffer by one byte into
the adjacent last_mic_err_time field.
rtw_parse_wpa_ie() does not prevent this: its length consistency check
compares *(wpa_ie+1) against (u8)(wpa_ie_len-2), which is (u8)(255) == 255
when wpa_ie_len = 257, so the check passes silently.
Add explicit bounds checks for both the WPA and WPA2 paths before the
memcpy, rejecting any IE whose total size (wpa_ielen + 2) exceeds the
supplicant_ie buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/io-wq: re-check IO_WQ_BIT_EXIT for each linked work item
commit 10dc95939817 ("io_uring/io-wq: check IO_WQ_BIT_EXIT inside work
run loop") fixed the obvious case where io_worker_handle_work() took one
exit-bit snapshot before draining pending work, but the fix stops one
level too early.
io_worker_handle_work() now re-checks IO_WQ_BIT_EXIT in its outer work
run loop, yet it still snapshots that bit once before processing a whole
dependent linked-work chain. If io_wq_exit_start() sets IO_WQ_BIT_EXIT
after the first linked item has started, the remaining linked items can
still reuse stale do_kill = false, skip IO_WQ_WORK_CANCEL, and continue
running after exit has begun.
Move the check further inside, so it covers linked items too. Note: this
is a syzbot special as it loves setting up tons of slow linked work on
weird devices like msr that take forever to read, and immediately close
the ring. Exit then takes a long time. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: fix exchmaps reservation limit check
xfs_exchmaps_estimate_overhead() adds the bmbt and rmapbt
overhead to a local resblks variable, but the final UINT_MAX
check still tests req->resblks. That is the reservation value
from before the overhead was added.
The computed value is stored back in req->resblks and later passed
to xfs_trans_alloc(), whose block reservation argument is unsigned
int. Check the computed reservation so the existing limit applies
to the value that will be used. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: kalmia: bound RX frame length in kalmia_rx_fixup()
kalmia_rx_fixup() computes usb_packet_length = skb->len - (2 *
KALMIA_HEADER_LENGTH) as a u16, guarded only by a pre-loop check that
skb->len is at least KALMIA_HEADER_LENGTH, which is 6. A device can
deliver a short bulk-IN frame with skb->len in the 6 to 11 range, or
leave a short trailing remainder on a later loop iteration. Either case
underflows usb_packet_length to about 65530.
That bypasses the usb_packet_length < ether_packet_length truncation path.
The device-supplied ether_packet_length, a le16 up to 65535 read from
header_start[2], then drives a memcmp() and the following skb_trim() and
skb_pull() past the end of the rx buffer. The rx buffer is hard_mtu * 10,
which is 14000 bytes. That is an out of bounds read.
Require both the start and end framing headers to be present before
subtracting them, on every loop iteration. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: composite: fix dead empty check in the USB_DT_OTG handler
The OTG branch of composite_setup() falls back to the first
configuration when none is selected:
if (cdev->config)
config = cdev->config;
else
config = list_first_entry(&cdev->configs,
struct usb_configuration, list);
if (!config)
goto done;
...
memcpy(req->buf, config->descriptors[0], value);
list_first_entry() never returns NULL. On an empty list it returns
container_of() of the list head. So the "if (!config)" check is dead.
When cdev->configs is empty, config points at the head inside struct
usb_composite_dev. config->descriptors[0] reads whatever sits at that
offset. The memcpy copies up to w_length bytes of it into the response
buffer.
cdev->configs can be empty in two cases. One is a teardown race on
gadget unbind with a control transfer in flight. The other is a driver
that sets is_otg before it adds a config. A reproducer that holds
cdev->configs empty triggers a KASAN fault in this branch.
Use list_first_entry_or_null() so the existing check does its job. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpm: Validate SVID index in svdm_consume_modes()
In svdm_consume_modes(), the SVID value is read from pmdata->svids using
pmdata->svid_index as an array index without bounds validation:
paltmode->svid = pmdata->svids[pmdata->svid_index];
If pmdata->svid_index is driven beyond SVID_DISCOVERY_MAX (16), it results
in an out-of-bounds read of the pmdata->svids array. Because pd_mode_data
is embedded inside struct tcpm_port, indexing past svids reads into
adjacent fields. In particular:
- At index 16, it reads the altmodes count.
- At index 18 and beyond, it reads into altmode_desc[], which contains
partner-supplied SVDM Discovery Modes VDOs.
By injecting a chosen SVID into altmode_desc[0].vdo and driving svid_index
to 20, the partner can force paltmode->svid to be loaded with an arbitrary,
partner- chosen SVID, which is then registered via
typec_partner_register_altmode().
Fix this by validating that pmdata->svid_index is non-negative and strictly
less than pmdata->nsvids before accessing the pmdata->svids array inside
svdm_consume_modes(). |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: guest_memfd: Treat memslot binding offset+size as unsigned values
When binding a memslot to a guest_memfd file, treat the offset and size as
unsigned values to fix a bug where the sum of the two can result in a false
negative when checking for overflow against the size of the file. Passing
unsigned values also avoids relying on somewhat obscure checks in other
flows for safety, and tracks the offset and size as they are intended to be
tracked, as unsigned values.
On 64-bit kernels, the number of pages a memslot contains and thus the size
(and offset) of its guest_memfd binding are unsigned 64-bit values. Taking
the offset+size as an loff_t instead of a uoff_t inadvertently converts
the unsigned value to a signed value if the offset and/or size is massive.
Locally storing the offset and size as signed values is benign in and of
itself (though even that is *extremely* difficult to discern), but
operating on their sum is not.
For the offset, KVM explicitly checks against a negative value, which might
seem like a bug as KVM could incorrectly reject a legitimate binding, but
that's not actually the case as KVM_CREATE_GUEST_MEMFD takes a signed value
for its size, i.e. a would-be-negative offset is also greater than the
maximum possible size of any guest_memfd file.
Regarding the size, while KVM lacks an explicit check for a negative value,
i.e. seemingly has a flawed overflow check, KVM restricts the number of
pages in a single memslot to the largest positive signed 32-bit value:
if (id < KVM_USER_MEM_SLOTS &&
(mem->memory_size >> PAGE_SHIFT) > KVM_MEM_MAX_NR_PAGES)
return -EINVAL;
and so that maximum "size" will ever be is 0x7fffffff000.
The sum of the two is, however, problematic. While the size is restricted
by KVM's memslot logic, the offset is not, i.e. the offset is completely
unchecked until the "offset + size > i_size_read(inode)" check. If the
offset is the (nearly) largest possible _positive_ value, then adding size
to the offset can result in a signed, negative 64-bit value. When compared
against the size of the file (guaranteed to be positive), the negative sum
is always smaller, and KVM incorrectly allows the absurd offset.
Opportunistically add missing includes in kvm_mm.h (instead of relying on
its parents). |
| In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - fix touch indexing for MMS134S and MMS136
The MMS134S and MMS136 touch controllers have an event size of 6 bytes
rather than 8 bytes. When __mms114_read_reg() reads the touch data
packet from the device into the touch buffer, the events are packed
tightly at 6-byte intervals. However, the driver iterates through the
events using standard C array indexing (touch[index]), where each
element is sizeof(struct mms114_touch) (8 bytes) apart. As a result, any
touch events beyond the first one are read from incorrect offsets and
parsed improperly.
Fix this by explicitly calculating the byte offset for each touch event
based on the device's specific event size. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: touchwin - reset the packet index on every complete packet
tw_interrupt() accumulates each non-zero serial byte into a fixed
three-byte buffer with a running index that is only reset once a full
packet has been received *and* the device's two Y bytes agree:
tw->data[tw->idx++] = data;
if (tw->idx == TW_LENGTH && tw->data[1] == tw->data[2]) {
...
tw->idx = 0;
}
The reset is gated on tw->data[1] == tw->data[2], a value the device
controls. A malicious, malfunctioning or counterfeit Touchwindow
peripheral can stream non-zero bytes whose 2nd and 3rd bytes differ: the
index reaches TW_LENGTH without the equality holding, is never reset, and
keeps growing, so tw->data[tw->idx++] walks off the end of the three-byte
array and the rest of the heap-allocated struct tw, one attacker-chosen
byte at a time -- an unbounded, device-driven heap out-of-bounds write.
Reset the index on every completed packet and report an event only when
the two Y bytes match, like the other serio touchscreen drivers do. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: don't wrap around quota ids in dqiterate
LOLLM noticed that q_id is an unsigned 32-bit variable. If it happens
to be set to XFS_DQ_ID_MAX due to a filesystem that actually has a dquot
for ID_MAX, then this addition will truncate to zero and the iteration
starts over. Fix this by casting to u64. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: elan_i2c - validate firmware size before use
Ensure that the firmware file is large enough to contain the expected
number of pages and the signature (which resides at the end of the
firmware blob) before accessing them to prevent potential out-of-bounds
reads. |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-af: CGX: add bounds check to cgx_speed_mbps index
cgx_speed_mbps has 13 elements but RESP_LINKSTAT_SPEED can yield values
0-15. If it returns a value >= 13, this causes an out-of-bounds array
access. Add a bounds check and default to speed 0 if the index is out of
range. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Remove latent out-of-bounds access in IOMMU debugfs
In iommu_mmio_write() and iommu_capability_write(), the variables
dbg_mmio_offset and dbg_cap_offset are declared as int. However, they
are populated using kstrtou32_from_user(). If a user provides a
sufficiently large value, it can become a negative integer.
Prior to this patch, the AMD IOMMU debugfs implementation was already
protected by different mechanisms.
1. #define OFS_IN_SZ 8 ensures the user string <= 8 bytes, so
e.g. 0xffffffff isn't a valid input.
if (cnt > OFS_IN_SZ)
return -EINVAL;
2. Implicit type promotion in iommu_mmio_write(), dbg_mmio_offset is int
and iommu->mmio_phys_end is u64
if (dbg_mmio_offset > iommu->mmio_phys_end - sizeof(u64))
return -EINVAL;
3. The show handlers would currently catch the negative number and
refuse to perform the read.
Replace kstrtou32_from_user() with kstrtos32_from_user() to parse the
input, and check for negative values to explicitly prevent out-of-bounds
memory accesses directly in iommu_mmio_write() and
iommu_capability_write(). |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Do not call map->ops->elt_free() if elt_alloc() fails
In paths where tracing_map_elt_alloc() failed to allocate objects,
the map->ops->elt_alloc() call was never successful. In this case,
map->ops->elt_free() should not be called. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ifb: report ethtool stats over num_tx_queues
ifb_dev_init() allocates dp->tx_private to dev->num_tx_queues
entries via kzalloc_objs(*txp, dev->num_tx_queues). Both IFB
per-queue RX and TX stats live in those entries: ifb_xmit() updates
txp->rx_stats using the skb queue mapping, ifb_ri_tasklet() updates
txp->tx_stats, and ifb_stats64() aggregates both over
dev->num_tx_queues.
The ethtool stats callbacks instead size and walk the per-queue
stats with dev->real_num_rx_queues and dev->real_num_tx_queues. With
an asymmetric device where the RX queue count exceeds the TX queue
count, for example:
ip link add name ifb10 numtxqueues 1 numrxqueues 8 type ifb
ethtool -S ifb10
ifb_get_ethtool_stats() indexes past the tx_private allocation and
copies adjacent slab data through ETHTOOL_GSTATS.
Use dev->num_tx_queues consistently for the stats strings, the
stats count, and the stats data walks. This reports one RX stats
group and one TX stats group for each backing ifb_q_private entry,
which is the queue set IFB can actually populate.
Reproduced under UML+KASAN at v7.1-rc2:
BUG: KASAN: slab-out-of-bounds in ifb_fill_stats_data+0x3c/0xae
Read of size 8 at addr 0000000062dbd228 by task ethtool/36
ifb_fill_stats_data+0x3c/0xae
ifb_get_ethtool_stats+0xc0/0x129
__dev_ethtool+0x1ca5/0x363c
dev_ethtool+0x123/0x1b3
dev_ioctl+0x56c/0x744
sock_do_ioctl+0x15f/0x1b2
sock_ioctl+0x4d5/0x50a
sys_ioctl+0xd8b/0xde9
With the patch applied, the same UML+KASAN repro is silent and
ethtool -S ifb10 reports only the stats backed by the single
allocated tx_private entry. |