| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
dma-debug: prevent an error message from causing runtime problems
For some drivers, that use the DMA API. This error message can be reached
several millions of times per second, causing spam to the kernel's printk
buffer and bringing the CPU usage up to 100% (so, it should be rate
limited). However, since there is at least one driver that is in the
mainline and suffers from the error condition, it is more useful to
err_printk() here instead of just rate limiting the error message (in hopes
that it will make it easier for other drivers that suffer from this issue
to be spotted). |
| In the Linux kernel, the following vulnerability has been resolved:
enetc: Fix illegal access when reading affinity_hint
irq_set_affinity_hit() stores a reference to the cpumask_t
parameter in the irq descriptor, and that reference can be
accessed later from irq_affinity_hint_proc_show(). Since
the cpu_mask parameter passed to irq_set_affinity_hit() has
only temporary storage (it's on the stack memory), later
accesses to it are illegal. Thus reads from the corresponding
procfs affinity_hint file can result in paging request oops.
The issue is fixed by the get_cpu_mask() helper, which provides
a permanent storage for the cpumask_t parameter. |
| In the Linux kernel, the following vulnerability has been resolved:
afs: Fix corruption in reads at fpos 2G-4G from an OpenAFS server
AFS-3 has two data fetch RPC variants, FS.FetchData and FS.FetchData64, and
Linux's afs client switches between them when talking to a non-YFS server
if the read size, the file position or the sum of the two have the upper 32
bits set of the 64-bit value.
This is a problem, however, since the file position and length fields of
FS.FetchData are *signed* 32-bit values.
Fix this by capturing the capability bits obtained from the fileserver when
it's sent an FS.GetCapabilities RPC, rather than just discarding them, and
then picking out the VICED_CAPABILITY_64BITFILES flag. This can then be
used to decide whether to use FS.FetchData or FS.FetchData64 - and also
FS.StoreData or FS.StoreData64 - rather than using upper_32_bits() to
switch on the parameter values.
This capabilities flag could also be used to limit the maximum size of the
file, but all servers must be checked for that.
Note that the issue does not exist with FS.StoreData - that uses *unsigned*
32-bit values. It's also not a problem with Auristor servers as its
YFS.FetchData64 op uses unsigned 64-bit values.
This can be tested by cloning a git repo through an OpenAFS client to an
OpenAFS server and then doing "git status" on it from a Linux afs
client[1]. Provided the clone has a pack file that's in the 2G-4G range,
the git status will show errors like:
error: packfile .git/objects/pack/pack-5e813c51d12b6847bbc0fcd97c2bca66da50079c.pack does not match index
error: packfile .git/objects/pack/pack-5e813c51d12b6847bbc0fcd97c2bca66da50079c.pack does not match index
This can be observed in the server's FileLog with something like the
following appearing:
Sun Aug 29 19:31:39 2021 SRXAFS_FetchData, Fid = 2303380852.491776.3263114, Host 192.168.11.201:7001, Id 1001
Sun Aug 29 19:31:39 2021 CheckRights: len=0, for host=192.168.11.201:7001
Sun Aug 29 19:31:39 2021 FetchData_RXStyle: Pos 18446744071815340032, Len 3154
Sun Aug 29 19:31:39 2021 FetchData_RXStyle: file size 2400758866
...
Sun Aug 29 19:31:40 2021 SRXAFS_FetchData returns 5
Note the file position of 18446744071815340032. This is the requested file
position sign-extended. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/sched: Avoid data corruptions
Wait for all dependencies of a job to complete before
killing it to avoid data corruptions. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio-net: Add validation for used length
This adds validation for used length (might come
from an untrusted device) to avoid data corruption
or loss. |
| In the Linux kernel, the following vulnerability has been resolved:
ubifs: Fix races between xattr_{set|get} and listxattr operations
UBIFS may occur some problems with concurrent xattr_{set|get} and
listxattr operations, such as assertion failure, memory corruption,
stale xattr value[1].
Fix it by importing a new rw-lock in @ubifs_inode to serilize write
operations on xattr, concurrent read operations are still effective,
just like ext4.
[1] https://lore.kernel.org/linux-mtd/20200630130438.141649-1-houtao1@huawei.com |
| In the Linux kernel, the following vulnerability has been resolved:
wl1251: Fix possible buffer overflow in wl1251_cmd_scan
Function wl1251_cmd_scan calls memcpy without checking the length.
Harden by checking the length is within the maximum allowed size. |
| In the Linux kernel, the following vulnerability has been resolved:
dm btree remove: assign new_root only when removal succeeds
remove_raw() in dm_btree_remove() may fail due to IO read error
(e.g. read the content of origin block fails during shadowing),
and the value of shadow_spine::root is uninitialized, but
the uninitialized value is still assign to new_root in the
end of dm_btree_remove().
For dm-thin, the value of pmd->details_root or pmd->root will become
an uninitialized value, so if trying to read details_info tree again
out-of-bound memory may occur as showed below:
general protection fault, probably for non-canonical address 0x3fdcb14c8d7520
CPU: 4 PID: 515 Comm: dmsetup Not tainted 5.13.0-rc6
Hardware name: QEMU Standard PC
RIP: 0010:metadata_ll_load_ie+0x14/0x30
Call Trace:
sm_metadata_count_is_more_than_one+0xb9/0xe0
dm_tm_shadow_block+0x52/0x1c0
shadow_step+0x59/0xf0
remove_raw+0xb2/0x170
dm_btree_remove+0xf4/0x1c0
dm_pool_delete_thin_device+0xc3/0x140
pool_message+0x218/0x2b0
target_message+0x251/0x290
ctl_ioctl+0x1c4/0x4d0
dm_ctl_ioctl+0xe/0x20
__x64_sys_ioctl+0x7b/0xb0
do_syscall_64+0x40/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixing it by only assign new_root when removal succeeds |
| In the Linux kernel, the following vulnerability has been resolved:
media: nxp: imx8-isi: Fix streaming cleanup on release
The current implementation unconditionally calls
mxc_isi_video_cleanup_streaming() in mxc_isi_video_release(). This can
lead to situations where any release call (like from a simple
"v4l2-ctl -l") may release a currently streaming queue when called on
such a device.
This is reproducible on an i.MX8MP board by streaming from an ISI
capture device using gstreamer:
gst-launch-1.0 -v v4l2src device=/dev/videoX ! \
video/x-raw,format=GRAY8,width=1280,height=800,framerate=1/120 ! \
fakesink
While this stream is running, querying the caps of the same device
provokes the error state:
v4l2-ctl -l -d /dev/videoX
This results in the following trace:
[ 155.452152] ------------[ cut here ]------------
[ 155.452163] WARNING: CPU: 0 PID: 1708 at drivers/media/platform/nxp/imx8-isi/imx8-isi-pipe.c:713 mxc_isi_pipe_irq_handler+0x19c/0x1b0 [imx8_isi]
[ 157.004248] Modules linked in: cfg80211 rpmsg_ctrl rpmsg_char rpmsg_tty virtio_rpmsg_bus rpmsg_ns rpmsg_core rfkill nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables mcp251x6
[ 157.053499] CPU: 0 UID: 0 PID: 1708 Comm: python3 Not tainted 6.15.4-00114-g1f61ca5cad76 #1 PREEMPT
[ 157.064369] Hardware name: imx8mp_board_01 (DT)
[ 157.068205] pstate: 400000c5 (nZcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 157.075169] pc : mxc_isi_pipe_irq_handler+0x19c/0x1b0 [imx8_isi]
[ 157.081195] lr : mxc_isi_pipe_irq_handler+0x38/0x1b0 [imx8_isi]
[ 157.087126] sp : ffff800080003ee0
[ 157.090438] x29: ffff800080003ee0 x28: ffff0000c3688000 x27: 0000000000000000
[ 157.097580] x26: 0000000000000000 x25: ffff0000c1e7ac00 x24: ffff800081b5ad50
[ 157.104723] x23: 00000000000000d1 x22: 0000000000000000 x21: ffff0000c25e4000
[ 157.111866] x20: 0000000060000200 x19: ffff80007a0608d0 x18: 0000000000000000
[ 157.119008] x17: ffff80006a4e3000 x16: ffff800080000000 x15: 0000000000000000
[ 157.126146] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
[ 157.133287] x11: 0000000000000040 x10: ffff0000c01445f0 x9 : ffff80007a053a38
[ 157.140425] x8 : ffff0000c04004b8 x7 : 0000000000000000 x6 : 0000000000000000
[ 157.147567] x5 : ffff0000c0400490 x4 : ffff80006a4e3000 x3 : ffff0000c25e4000
[ 157.154706] x2 : 0000000000000000 x1 : ffff8000825c0014 x0 : 0000000060000200
[ 157.161850] Call trace:
[ 157.164296] mxc_isi_pipe_irq_handler+0x19c/0x1b0 [imx8_isi] (P)
[ 157.170319] __handle_irq_event_percpu+0x58/0x218
[ 157.175029] handle_irq_event+0x54/0xb8
[ 157.178867] handle_fasteoi_irq+0xac/0x248
[ 157.182968] handle_irq_desc+0x48/0x68
[ 157.186723] generic_handle_domain_irq+0x24/0x38
[ 157.191346] gic_handle_irq+0x54/0x120
[ 157.195098] call_on_irq_stack+0x24/0x30
[ 157.199027] do_interrupt_handler+0x88/0x98
[ 157.203212] el0_interrupt+0x44/0xc0
[ 157.206792] __el0_irq_handler_common+0x18/0x28
[ 157.211328] el0t_64_irq_handler+0x10/0x20
[ 157.215429] el0t_64_irq+0x198/0x1a0
[ 157.219009] ---[ end trace 0000000000000000 ]---
Address this issue by moving the streaming preparation and cleanup to
the vb2 .prepare_streaming() and .unprepare_streaming() operations. This
also simplifies the driver by allowing direct usage of the
vb2_ioctl_streamon() and vb2_ioctl_streamoff() helpers, and removal of
the manual cleanup from mxc_isi_video_release(). |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_ct: add seqadj extension for natted connections
Sequence adjustment may be required for FTP traffic with PASV/EPSV modes.
due to need to re-write packet payload (IP, port) on the ftp control
connection. This can require changes to the TCP length and expected
seq / ack_seq.
The easiest way to reproduce this issue is with PASV mode.
Example ruleset:
table inet ftp_nat {
ct helper ftp_helper {
type "ftp" protocol tcp
l3proto inet
}
chain prerouting {
type filter hook prerouting priority 0; policy accept;
tcp dport 21 ct state new ct helper set "ftp_helper"
}
}
table ip nat {
chain prerouting {
type nat hook prerouting priority -100; policy accept;
tcp dport 21 dnat ip prefix to ip daddr map {
192.168.100.1 : 192.168.13.2/32 }
}
chain postrouting {
type nat hook postrouting priority 100 ; policy accept;
tcp sport 21 snat ip prefix to ip saddr map {
192.168.13.2 : 192.168.100.1/32 }
}
}
Note that the ftp helper gets assigned *after* the dnat setup.
The inverse (nat after helper assign) is handled by an existing
check in nf_nat_setup_info() and will not show the problem.
Topoloy:
+-------------------+ +----------------------------------+
| FTP: 192.168.13.2 | <-> | NAT: 192.168.13.3, 192.168.100.1 |
+-------------------+ +----------------------------------+
|
+-----------------------+
| Client: 192.168.100.2 |
+-----------------------+
ftp nat changes do not work as expected in this case:
Connected to 192.168.100.1.
[..]
ftp> epsv
EPSV/EPRT on IPv4 off.
ftp> ls
227 Entering passive mode (192,168,100,1,209,129).
421 Service not available, remote server has closed connection.
Kernel logs:
Missing nfct_seqadj_ext_add() setup call
WARNING: CPU: 1 PID: 0 at net/netfilter/nf_conntrack_seqadj.c:41
[..]
__nf_nat_mangle_tcp_packet+0x100/0x160 [nf_nat]
nf_nat_ftp+0x142/0x280 [nf_nat_ftp]
help+0x4d1/0x880 [nf_conntrack_ftp]
nf_confirm+0x122/0x2e0 [nf_conntrack]
nf_hook_slow+0x3c/0xb0
..
Fix this by adding the required extension when a conntrack helper is assigned
to a connection that has a nat binding. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme: fix admin request_queue lifetime
The namespaces can access the controller's admin request_queue, and
stale references on the namespaces may exist after tearing down the
controller. Ensure the admin request_queue is active by moving the
controller's 'put' to after all controller references have been released
to ensure no one is can access the request_queue. This fixes a reported
use-after-free bug:
BUG: KASAN: slab-use-after-free in blk_queue_enter+0x41c/0x4a0
Read of size 8 at addr ffff88c0a53819f8 by task nvme/3287
CPU: 67 UID: 0 PID: 3287 Comm: nvme Tainted: G E 6.13.2-ga1582f1a031e #15
Tainted: [E]=UNSIGNED_MODULE
Hardware name: Jabil /EGS 2S MB1, BIOS 1.00 06/18/2025
Call Trace:
<TASK>
dump_stack_lvl+0x4f/0x60
print_report+0xc4/0x620
? _raw_spin_lock_irqsave+0x70/0xb0
? _raw_read_unlock_irqrestore+0x30/0x30
? blk_queue_enter+0x41c/0x4a0
kasan_report+0xab/0xe0
? blk_queue_enter+0x41c/0x4a0
blk_queue_enter+0x41c/0x4a0
? __irq_work_queue_local+0x75/0x1d0
? blk_queue_start_drain+0x70/0x70
? irq_work_queue+0x18/0x20
? vprintk_emit.part.0+0x1cc/0x350
? wake_up_klogd_work_func+0x60/0x60
blk_mq_alloc_request+0x2b7/0x6b0
? __blk_mq_alloc_requests+0x1060/0x1060
? __switch_to+0x5b7/0x1060
nvme_submit_user_cmd+0xa9/0x330
nvme_user_cmd.isra.0+0x240/0x3f0
? force_sigsegv+0xe0/0xe0
? nvme_user_cmd64+0x400/0x400
? vfs_fileattr_set+0x9b0/0x9b0
? cgroup_update_frozen_flag+0x24/0x1c0
? cgroup_leave_frozen+0x204/0x330
? nvme_ioctl+0x7c/0x2c0
blkdev_ioctl+0x1a8/0x4d0
? blkdev_common_ioctl+0x1930/0x1930
? fdget+0x54/0x380
__x64_sys_ioctl+0x129/0x190
do_syscall_64+0x5b/0x160
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f765f703b0b
Code: ff ff ff 85 c0 79 9b 49 c7 c4 ff ff ff ff 5b 5d 4c 89 e0 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d dd 52 0f 00 f7 d8 64 89 01 48
RSP: 002b:00007ffe2cefe808 EFLAGS: 00000202 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007ffe2cefe860 RCX: 00007f765f703b0b
RDX: 00007ffe2cefe860 RSI: 00000000c0484e41 RDI: 0000000000000003
RBP: 0000000000000000 R08: 0000000000000003 R09: 0000000000000000
R10: 00007f765f611d50 R11: 0000000000000202 R12: 0000000000000003
R13: 00000000c0484e41 R14: 0000000000000001 R15: 00007ffe2cefea60
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
landlock: Fix handling of disconnected directories
Disconnected files or directories can appear when they are visible and
opened from a bind mount, but have been renamed or moved from the source
of the bind mount in a way that makes them inaccessible from the mount
point (i.e. out of scope).
Previously, access rights tied to files or directories opened through a
disconnected directory were collected by walking the related hierarchy
down to the root of the filesystem, without taking into account the
mount point because it couldn't be found. This could lead to
inconsistent access results, potential access right widening, and
hard-to-debug renames, especially since such paths cannot be printed.
For a sandboxed task to create a disconnected directory, it needs to
have write access (i.e. FS_MAKE_REG, FS_REMOVE_FILE, and FS_REFER) to
the underlying source of the bind mount, and read access to the related
mount point. Because a sandboxed task cannot acquire more access
rights than those defined by its Landlock domain, this could lead to
inconsistent access rights due to missing permissions that should be
inherited from the mount point hierarchy, while inheriting permissions
from the filesystem hierarchy hidden by this mount point instead.
Landlock now handles files and directories opened from disconnected
directories by taking into account the filesystem hierarchy when the
mount point is not found in the hierarchy walk, and also always taking
into account the mount point from which these disconnected directories
were opened. This ensures that a rename is not allowed if it would
widen access rights [1].
The rationale is that, even if disconnected hierarchies might not be
visible or accessible to a sandboxed task, relying on the collected
access rights from them improves the guarantee that access rights will
not be widened during a rename because of the access right comparison
between the source and the destination (see LANDLOCK_ACCESS_FS_REFER).
It may look like this would grant more access on disconnected files and
directories, but the security policies are always enforced for all the
evaluated hierarchies. This new behavior should be less surprising to
users and safer from an access control perspective.
Remove a wrong WARN_ON_ONCE() canary in collect_domain_accesses() and
fix the related comment.
Because opened files have their access rights stored in the related file
security properties, there is no impact for disconnected or unlinked
files. |
| A malicious actor in Wi-Fi range of the affected product could leverage a vulnerability in the airMAX Wireless Protocol to achieve a remote code execution (RCE) within the affected product. |
| A malicious actor with access to the network could exploit a Path Traversal vulnerability found in the UniFi Network Application to access files on the underlying system that could be manipulated to access an underlying account. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: iscsi: Fix conn use after free during resets
If we haven't done a unbind target call we can race where
iscsi_conn_teardown wakes up the EH thread and then frees the conn while
those threads are still accessing the conn ehwait.
We can only do one TMF per session so this just moves the TMF fields from
the conn to the session. We can then rely on the
iscsi_session_teardown->iscsi_remove_session->__iscsi_unbind_session call
to remove the target and it's devices, and know after that point there is
no device or scsi-ml callout trying to access the session. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/bpf: Fix detecting BPF atomic instructions
Commit 91c960b0056672 ("bpf: Rename BPF_XADD and prepare to encode other
atomics in .imm") converted BPF_XADD to BPF_ATOMIC and added a way to
distinguish instructions based on the immediate field. Existing JIT
implementations were updated to check for the immediate field and to
reject programs utilizing anything more than BPF_ADD (such as BPF_FETCH)
in the immediate field.
However, the check added to powerpc64 JIT did not look at the correct
BPF instruction. Due to this, such programs would be accepted and
incorrectly JIT'ed resulting in soft lockups, as seen with the atomic
bounds test. Fix this by looking at the correct immediate value. |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: fix NULL dereference in nfs3svc_encode_getaclres
In error cases the dentry may be NULL.
Before 20798dfe249a, the encoder also checked dentry and
d_really_is_positive(dentry), but that looks like overkill to me--zero
status should be enough to guarantee a positive dentry.
This isn't the first time we've seen an error-case NULL dereference
hidden in the initialization of a local variable in an xdr encoder. But
I went back through the other recent rewrites and didn't spot any
similar bugs. |
| In the Linux kernel, the following vulnerability has been resolved:
net: validate lwtstate->data before returning from skb_tunnel_info()
skb_tunnel_info() returns pointer of lwtstate->data as ip_tunnel_info
type without validation. lwtstate->data can have various types such as
mpls_iptunnel_encap, etc and these are not compatible.
So skb_tunnel_info() should validate before returning that pointer.
Splat looks like:
BUG: KASAN: slab-out-of-bounds in vxlan_get_route+0x418/0x4b0 [vxlan]
Read of size 2 at addr ffff888106ec2698 by task ping/811
CPU: 1 PID: 811 Comm: ping Not tainted 5.13.0+ #1195
Call Trace:
dump_stack_lvl+0x56/0x7b
print_address_description.constprop.8.cold.13+0x13/0x2ee
? vxlan_get_route+0x418/0x4b0 [vxlan]
? vxlan_get_route+0x418/0x4b0 [vxlan]
kasan_report.cold.14+0x83/0xdf
? vxlan_get_route+0x418/0x4b0 [vxlan]
vxlan_get_route+0x418/0x4b0 [vxlan]
[ ... ]
vxlan_xmit_one+0x148b/0x32b0 [vxlan]
[ ... ]
vxlan_xmit+0x25c5/0x4780 [vxlan]
[ ... ]
dev_hard_start_xmit+0x1ae/0x6e0
__dev_queue_xmit+0x1f39/0x31a0
[ ... ]
neigh_xmit+0x2f9/0x940
mpls_xmit+0x911/0x1600 [mpls_iptunnel]
lwtunnel_xmit+0x18f/0x450
ip_finish_output2+0x867/0x2040
[ ... ] |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libfc: Fix array index out of bound exception
Fix array index out of bound exception in fc_rport_prli_resp(). |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: prevent NULL deref in cifs_compose_mount_options()
The optional @ref parameter might contain an NULL node_name, so
prevent dereferencing it in cifs_compose_mount_options().
Addresses-Coverity: 1476408 ("Explicit null dereferenced") |
