| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: cdns3: gadget: fix NULL pointer dereference in ep_queue
When the gadget endpoint is disabled or not yet configured, the ep->desc
pointer can be NULL. This leads to a NULL pointer dereference when
__cdns3_gadget_ep_queue() is called, causing a kernel crash.
Add a check to return -ESHUTDOWN if ep->desc is NULL, which is the
standard return code for unconfigured endpoints.
This prevents potential crashes when ep_queue is called on endpoints
that are not ready. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: cdns3: gadget: fix state inconsistency on gadget init failure
When cdns3_gadget_start() fails, the DRD hardware is left in gadget mode
while software state remains INACTIVE, creating hardware/software state
inconsistency.
When switching to host mode via sysfs:
echo host > /sys/class/usb_role/13180000.usb-role-switch/role
The role state is not set to CDNS_ROLE_STATE_ACTIVE due to the error,
so cdns_role_stop() skips cleanup because state is still INACTIVE.
This violates the DRD controller design specification (Figure22),
which requires returning to idle state before switching roles.
This leads to a synchronous external abort in xhci_gen_setup() when
setting up the host controller:
[ 516.440698] configfs-gadget 13180000.usb: failed to start g1: -19
[ 516.442035] cdns-usb3 13180000.usb: Failed to add gadget
[ 516.443278] cdns-usb3 13180000.usb: set role 2 has failed
...
[ 1301.375722] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 1301.377716] Internal error: synchronous external abort: 96000010 [#1] PREEMPT SMP
[ 1301.382485] pc : xhci_gen_setup+0xa4/0x408
[ 1301.393391] backtrace:
...
xhci_gen_setup+0xa4/0x408 <-- CRASH
xhci_plat_setup+0x44/0x58
usb_add_hcd+0x284/0x678
...
cdns_role_set+0x9c/0xbc <-- Role switch
Fix by calling cdns_drd_gadget_off() in the error path to properly
clean up the DRD gadget state. |
| In the Linux kernel, the following vulnerability has been resolved:
auxdisplay: line-display: fix NULL dereference in linedisp_release
linedisp_release() currently retrieves the enclosing struct linedisp via
to_linedisp(). That lookup depends on the attachment list, but the
attachment may already have been removed before put_device() invokes the
release callback. This can happen in linedisp_unregister(), and can also
be reached from some linedisp_register() error paths.
In that case, to_linedisp() returns NULL and linedisp_release()
dereferences it while freeing the display resources.
The struct device released here is the embedded linedisp->dev used by
linedisp_register(), so retrieve the enclosing object directly with
container_of() instead. |
| In the Linux kernel, the following vulnerability has been resolved:
bridge: br_nd_send: validate ND option lengths
br_nd_send() walks ND options according to option-provided lengths.
A malformed option can make the parser advance beyond the computed
option span or use a too-short source LLADDR option payload.
Validate option lengths against the remaining NS option area before
advancing, and only read source LLADDR when the option is large enough
for an Ethernet address. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: dt2815: add hardware detection to prevent crash
The dt2815 driver crashes when attached to I/O ports without actual
hardware present. This occurs because syzkaller or users can attach
the driver to arbitrary I/O addresses via COMEDI_DEVCONFIG ioctl.
When no hardware exists at the specified port, inb() operations return
0xff (floating bus), but outb() operations can trigger page faults due
to undefined behavior, especially under race conditions:
BUG: unable to handle page fault for address: 000000007fffff90
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
RIP: 0010:dt2815_attach+0x6e0/0x1110
Add hardware detection by reading the status register before attempting
any write operations. If the read returns 0xff, assume no hardware is
present and fail the attach with -ENODEV. This prevents crashes from
outb() operations on non-existent hardware. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: runflags cannot determine whether to reclaim chanlist
syzbot reported a memory leak [1], because commit 4e1da516debb ("comedi:
Add reference counting for Comedi command handling") did not consider
the exceptional exit case in do_cmd_ioctl() where runflags is not set.
This caused chanlist not to be properly freed by do_become_nonbusy(),
as it only frees chanlist when runflags is correctly set.
Added a check in do_become_nonbusy() for the case where runflags is not
set, to properly free the chanlist memory.
[1]
BUG: memory leak
backtrace (crc 844a0efa):
__comedi_get_user_chanlist drivers/comedi/comedi_fops.c:1815 [inline]
do_cmd_ioctl.part.0+0x112/0x350 drivers/comedi/comedi_fops.c:1890
do_cmd_ioctl drivers/comedi/comedi_fops.c:1858 [inline] |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: ni_atmio16d: Fix invalid clean-up after failed attach
If the driver's COMEDI "attach" handler function (`atmio16d_attach()`)
returns an error, the COMEDI core will call the driver's "detach"
handler function (`atmio16d_detach()`) to clean up. This calls
`reset_atmio16d()` unconditionally, but depending on where the error
occurred in the attach handler, the device may not have been
sufficiently initialized to call `reset_atmio16d()`. It uses
`dev->iobase` as the I/O port base address and `dev->private` as the
pointer to the COMEDI device's private data structure. `dev->iobase`
may still be set to its initial value of 0, which would result in
undesired writes to low I/O port addresses. `dev->private` may still be
`NULL`, which would result in null pointer dereferences.
Fix `atmio16d_detach()` by checking that `dev->private` is valid
(non-null) before calling `reset_atmio16d()`. This implies that
`dev->iobase` was set correctly since that is set up before
`dev->private`. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: me_daq: Fix potential overrun of firmware buffer
`me2600_xilinx_download()` loads the firmware that was requested by
`request_firmware()`. It is possible for it to overrun the source
buffer because it blindly trusts the file format. It reads a data
stream length from the first 4 bytes into variable `file_length` and
reads the data stream contents of length `file_length` from offset 16
onwards. Although it checks that the supplied firmware is at least 16
bytes long, it does not check that it is long enough to contain the data
stream.
Add a test to ensure that the supplied firmware is long enough to
contain the header and the data stream. On failure, log an error and
return `-EINVAL`. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: me4000: Fix potential overrun of firmware buffer
`me4000_xilinx_download()` loads the firmware that was requested by
`request_firmware()`. It is possible for it to overrun the source
buffer because it blindly trusts the file format. It reads a data
stream length from the first 4 bytes into variable `file_length` and
reads the data stream contents of length `file_length` from offset 16
onwards.
Add a test to ensure that the supplied firmware is long enough to
contain the header and the data stream. On failure, log an error and
return `-EINVAL`.
Note: The firmware loading was totally broken before commit ac584af59945
("staging: comedi: me4000: fix firmware downloading"), but that is the
most sensible target for this fix. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/zcrypt: Fix memory leak with CCA cards used as accelerator
Tests showed that there is a memory leak if CCA cards are used as
accelerator for clear key RSA requests (ME and CRT). With the last
rework for the memory allocation the AP messages are allocated by
ap_init_apmsg() but for some reason on two places (ME and CRT) the
older allocation was still in place. So the first allocation simple
was never freed. |
| In the Linux kernel, the following vulnerability has been resolved:
reset: gpio: fix double free in reset_add_gpio_aux_device() error path
When __auxiliary_device_add() fails, reset_add_gpio_aux_device()
calls auxiliary_device_uninit(adev).
The device release callback reset_gpio_aux_device_release() frees
adev, but the current error path then calls kfree(adev) again,
causing a double free.
Keep kfree(adev) for the auxiliary_device_init() failure path, but
avoid freeing adev after auxiliary_device_uninit(). |
| In the Linux kernel, the following vulnerability has been resolved:
PM: EM: Fix NULL pointer dereference when perf domain ID is not found
dev_energymodel_nl_get_perf_domains_doit() calls
em_perf_domain_get_by_id() but does not check the return value before
passing it to __em_nl_get_pd_size(). When a caller supplies a
non-existent perf domain ID, em_perf_domain_get_by_id() returns NULL,
and __em_nl_get_pd_size() immediately dereferences pd->cpus
(struct offset 0x30), causing a NULL pointer dereference.
The sister handler dev_energymodel_nl_get_perf_table_doit() already
handles this correctly via __em_nl_get_pd_table_id(), which returns
NULL and causes the caller to return -EINVAL. Add the same NULL check
in the get-perf-domains do handler.
[ rjw: Subject and changelog edits ] |
| In the Linux kernel, the following vulnerability has been resolved:
nvmem: zynqmp_nvmem: Fix buffer size in DMA and memcpy
Buffer size used in dma allocation and memcpy is wrong.
It can lead to undersized DMA buffer access and possible
memory corruption. use correct buffer size in dma_alloc_coherent
and memcpy. |
| In the Linux kernel, the following vulnerability has been resolved:
vt: discard stale unicode buffer on alt screen exit after resize
When enter_alt_screen() saves vc_uni_lines into vc_saved_uni_lines and
sets vc_uni_lines to NULL, a subsequent console resize via vc_do_resize()
skips reallocating the unicode buffer because vc_uni_lines is NULL.
However, vc_saved_uni_lines still points to the old buffer allocated for
the original dimensions.
When leave_alt_screen() later restores vc_saved_uni_lines, the buffer
dimensions no longer match vc_rows/vc_cols. Any operation that iterates
over the unicode buffer using the current dimensions (e.g. csi_J clearing
the screen) will access memory out of bounds, causing a kernel oops:
BUG: unable to handle page fault for address: 0x0000002000000020
RIP: 0010:csi_J+0x133/0x2d0
The faulting address 0x0000002000000020 is two adjacent u32 space
characters (0x20) interpreted as a pointer, read from the row data area
past the end of the 25-entry pointer array in a buffer allocated for
80x25 but accessed with 240x67 dimensions.
Fix this by checking whether the console dimensions changed while in the
alternate screen. If they did, free the stale saved buffer instead of
restoring it. The unicode screen will be lazily rebuilt via
vc_uniscr_check() when next needed. |
| In the Linux kernel, the following vulnerability has been resolved:
counter: rz-mtu3-cnt: prevent counter from being toggled multiple times
Runtime PM counter is incremented / decremented each time the sysfs
enable file is written to.
If user writes 0 to the sysfs enable file multiple times, runtime PM
usage count underflows, generating the following message.
rz-mtu3-counter rz-mtu3-counter.0: Runtime PM usage count underflow!
At the same time, hardware registers end up being accessed with clocks
off in rz_mtu3_terminate_counter() to disable an already disabled
channel.
If user writes 1 to the sysfs enable file multiple times, runtime PM
usage count will be incremented each time, requiring the same number of
0 writes to get it back to 0.
If user writes 0 to the sysfs enable file while PWM is in progress, PWM
is stopped without counter being the owner of the underlying MTU3
channel.
Check against the cached count_is_enabled value and exit if the user
is trying to set the same enable value. |
| In the Linux kernel, the following vulnerability has been resolved:
counter: rz-mtu3-cnt: do not use struct rz_mtu3_channel's dev member
The counter driver can use HW channels 1 and 2, while the PWM driver can
use HW channels 0, 1, 2, 3, 4, 6, 7.
The dev member is assigned both by the counter driver and the PWM driver
for channels 1 and 2, to their own struct device instance, overwriting
the previous value.
The sub-drivers race to assign their own struct device pointer to the
same struct rz_mtu3_channel's dev member.
The dev member of struct rz_mtu3_channel is used by the counter
sub-driver for runtime PM.
Depending on the probe order of the counter and PWM sub-drivers, the
dev member may point to the wrong struct device instance, causing the
counter sub-driver to do runtime PM actions on the wrong device.
To fix this, use the parent pointer of the counter, which is assigned
during probe to the correct struct device, not the struct device pointer
inside the shared struct rz_mtu3_channel. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: tegra - Add missing CRYPTO_ALG_ASYNC
The tegra crypto driver failed to set the CRYPTO_ALG_ASYNC on its
asynchronous algorithms, causing the crypto API to select them for users
that request only synchronous algorithms. This causes crashes (at
least). Fix this by adding the flag like what the other drivers do.
Also remove the unnecessary CRYPTO_ALG_TYPE_* flags, since those just
get ignored and overridden by the registration function anyway. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: validate ND option lengths in vxlan_na_create
vxlan_na_create() walks ND options according to option-provided
lengths. A malformed option can make the parser advance beyond the
computed option span or use a too-short source LLADDR option payload.
Validate option lengths against the remaining NS option area before
advancing, and only read source LLADDR when the option is large enough
for an Ethernet address. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ftgmac100: fix ring allocation unwind on open failure
ftgmac100_alloc_rings() allocates rx_skbs, tx_skbs, rxdes, txdes, and
rx_scratch in stages. On intermediate failures it returned -ENOMEM
directly, leaking resources allocated earlier in the function.
Rework the failure path to use staged local unwind labels and free
allocated resources in reverse order before returning -ENOMEM. This
matches common netdev allocation cleanup style. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: mtk_ppe: avoid NULL deref when gmac0 is disabled
If the gmac0 is disabled, the precheck for a valid ingress device will
cause a NULL pointer deref and crash the system. This happens because
eth->netdev[0] will be NULL but the code will directly try to access
netdev_ops.
Instead of just checking for the first net_device, it must be checked if
any of the mtk_eth net_devices is matching the netdev_ops of the ingress
device. |
