| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
soundwire: qcom: fix storing port config out-of-bounds
The 'qcom_swrm_ctrl->pconfig' has size of QCOM_SDW_MAX_PORTS (14),
however we index it starting from 1, not 0, to match real port numbers.
This can lead to writing port config past 'pconfig' bounds and
overwriting next member of 'qcom_swrm_ctrl' struct. Reported also by
smatch:
drivers/soundwire/qcom.c:1269 qcom_swrm_get_port_config() error: buffer overflow 'ctrl->pconfig' 14 <= 14 |
| In the Linux kernel, the following vulnerability has been resolved:
ibmvnic: Do not reset dql stats on NON_FATAL err
All ibmvnic resets, make a call to netdev_tx_reset_queue() when
re-opening the device. netdev_tx_reset_queue() resets the num_queued
and num_completed byte counters. These stats are used in Byte Queue
Limit (BQL) algorithms. The difference between these two stats tracks
the number of bytes currently sitting on the physical NIC. ibmvnic
increases the number of queued bytes though calls to
netdev_tx_sent_queue() in the drivers xmit function. When, VIOS reports
that it is done transmitting bytes, the ibmvnic device increases the
number of completed bytes through calls to netdev_tx_completed_queue().
It is important to note that the driver batches its transmit calls and
num_queued is increased every time that an skb is added to the next
batch, not necessarily when the batch is sent to VIOS for transmission.
Unlike other reset types, a NON FATAL reset will not flush the sub crq
tx buffers. Therefore, it is possible for the batched skb array to be
partially full. So if there is call to netdev_tx_reset_queue() when
re-opening the device, the value of num_queued (0) would not account
for the skb's that are currently batched. Eventually, when the batch
is sent to VIOS, the call to netdev_tx_completed_queue() would increase
num_completed to a value greater than the num_queued. This causes a
BUG_ON crash:
ibmvnic 30000002: Firmware reports error, cause: adapter problem.
Starting recovery...
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
------------[ cut here ]------------
kernel BUG at lib/dynamic_queue_limits.c:27!
Oops: Exception in kernel mode, sig: 5
[....]
NIP dql_completed+0x28/0x1c0
LR ibmvnic_complete_tx.isra.0+0x23c/0x420 [ibmvnic]
Call Trace:
ibmvnic_complete_tx.isra.0+0x3f8/0x420 [ibmvnic] (unreliable)
ibmvnic_interrupt_tx+0x40/0x70 [ibmvnic]
__handle_irq_event_percpu+0x98/0x270
---[ end trace ]---
Therefore, do not reset the dql stats when performing a NON_FATAL reset. |
| In the Linux kernel, the following vulnerability has been resolved:
hsr: Fix uninit-value access in fill_frame_info()
Syzbot reports the following uninit-value access problem.
=====================================================
BUG: KMSAN: uninit-value in fill_frame_info net/hsr/hsr_forward.c:601 [inline]
BUG: KMSAN: uninit-value in hsr_forward_skb+0x9bd/0x30f0 net/hsr/hsr_forward.c:616
fill_frame_info net/hsr/hsr_forward.c:601 [inline]
hsr_forward_skb+0x9bd/0x30f0 net/hsr/hsr_forward.c:616
hsr_dev_xmit+0x192/0x330 net/hsr/hsr_device.c:223
__netdev_start_xmit include/linux/netdevice.h:4889 [inline]
netdev_start_xmit include/linux/netdevice.h:4903 [inline]
xmit_one net/core/dev.c:3544 [inline]
dev_hard_start_xmit+0x247/0xa10 net/core/dev.c:3560
__dev_queue_xmit+0x34d0/0x52a0 net/core/dev.c:4340
dev_queue_xmit include/linux/netdevice.h:3082 [inline]
packet_xmit+0x9c/0x6b0 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3087 [inline]
packet_sendmsg+0x8b1d/0x9f30 net/packet/af_packet.c:3119
sock_sendmsg_nosec net/socket.c:730 [inline]
sock_sendmsg net/socket.c:753 [inline]
__sys_sendto+0x781/0xa30 net/socket.c:2176
__do_sys_sendto net/socket.c:2188 [inline]
__se_sys_sendto net/socket.c:2184 [inline]
__ia32_sys_sendto+0x11f/0x1c0 net/socket.c:2184
do_syscall_32_irqs_on arch/x86/entry/common.c:112 [inline]
__do_fast_syscall_32+0xa2/0x100 arch/x86/entry/common.c:178
do_fast_syscall_32+0x37/0x80 arch/x86/entry/common.c:203
do_SYSENTER_32+0x1f/0x30 arch/x86/entry/common.c:246
entry_SYSENTER_compat_after_hwframe+0x70/0x82
Uninit was created at:
slab_post_alloc_hook+0x12f/0xb70 mm/slab.h:767
slab_alloc_node mm/slub.c:3478 [inline]
kmem_cache_alloc_node+0x577/0xa80 mm/slub.c:3523
kmalloc_reserve+0x148/0x470 net/core/skbuff.c:559
__alloc_skb+0x318/0x740 net/core/skbuff.c:644
alloc_skb include/linux/skbuff.h:1286 [inline]
alloc_skb_with_frags+0xc8/0xbd0 net/core/skbuff.c:6299
sock_alloc_send_pskb+0xa80/0xbf0 net/core/sock.c:2794
packet_alloc_skb net/packet/af_packet.c:2936 [inline]
packet_snd net/packet/af_packet.c:3030 [inline]
packet_sendmsg+0x70e8/0x9f30 net/packet/af_packet.c:3119
sock_sendmsg_nosec net/socket.c:730 [inline]
sock_sendmsg net/socket.c:753 [inline]
__sys_sendto+0x781/0xa30 net/socket.c:2176
__do_sys_sendto net/socket.c:2188 [inline]
__se_sys_sendto net/socket.c:2184 [inline]
__ia32_sys_sendto+0x11f/0x1c0 net/socket.c:2184
do_syscall_32_irqs_on arch/x86/entry/common.c:112 [inline]
__do_fast_syscall_32+0xa2/0x100 arch/x86/entry/common.c:178
do_fast_syscall_32+0x37/0x80 arch/x86/entry/common.c:203
do_SYSENTER_32+0x1f/0x30 arch/x86/entry/common.c:246
entry_SYSENTER_compat_after_hwframe+0x70/0x82
It is because VLAN not yet supported in hsr driver. Return error
when protocol is ETH_P_8021Q in fill_frame_info() now to fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: multitouch: Correct devm device reference for hidinput input_dev name
Reference the HID device rather than the input device for the devm
allocation of the input_dev name. Referencing the input_dev would lead to a
use-after-free when the input_dev was unregistered and subsequently fires a
uevent that depends on the name. At the point of firing the uevent, the
name would be freed by devres management.
Use devm_kasprintf to simplify the logic for allocating memory and
formatting the input_dev name string. |
| In the Linux kernel, the following vulnerability has been resolved:
net: qrtr: Fix a refcount bug in qrtr_recvmsg()
Syzbot reported a bug as following:
refcount_t: addition on 0; use-after-free.
...
RIP: 0010:refcount_warn_saturate+0x17c/0x1f0 lib/refcount.c:25
...
Call Trace:
<TASK>
__refcount_add include/linux/refcount.h:199 [inline]
__refcount_inc include/linux/refcount.h:250 [inline]
refcount_inc include/linux/refcount.h:267 [inline]
kref_get include/linux/kref.h:45 [inline]
qrtr_node_acquire net/qrtr/af_qrtr.c:202 [inline]
qrtr_node_lookup net/qrtr/af_qrtr.c:398 [inline]
qrtr_send_resume_tx net/qrtr/af_qrtr.c:1003 [inline]
qrtr_recvmsg+0x85f/0x990 net/qrtr/af_qrtr.c:1070
sock_recvmsg_nosec net/socket.c:1017 [inline]
sock_recvmsg+0xe2/0x160 net/socket.c:1038
qrtr_ns_worker+0x170/0x1700 net/qrtr/ns.c:688
process_one_work+0x991/0x15c0 kernel/workqueue.c:2390
worker_thread+0x669/0x1090 kernel/workqueue.c:2537
It occurs in the concurrent scenario of qrtr_recvmsg() and
qrtr_endpoint_unregister() as following:
cpu0 cpu1
qrtr_recvmsg qrtr_endpoint_unregister
qrtr_send_resume_tx qrtr_node_release
qrtr_node_lookup mutex_lock(&qrtr_node_lock)
spin_lock_irqsave(&qrtr_nodes_lock, ) refcount_dec_and_test(&node->ref) [node->ref == 0]
radix_tree_lookup [node != NULL] __qrtr_node_release
qrtr_node_acquire spin_lock_irqsave(&qrtr_nodes_lock, )
kref_get(&node->ref) [WARNING] ...
mutex_unlock(&qrtr_node_lock)
Use qrtr_node_lock to protect qrtr_node_lookup() implementation, this
is actually improving the protection of node reference. |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: fix sysfs interface lifetime
The current nilfs2 sysfs support has issues with the timing of creation
and deletion of sysfs entries, potentially leading to null pointer
dereferences, use-after-free, and lockdep warnings.
Some of the sysfs attributes for nilfs2 per-filesystem instance refer to
metadata file "cpfile", "sufile", or "dat", but
nilfs_sysfs_create_device_group that creates those attributes is executed
before the inodes for these metadata files are loaded, and
nilfs_sysfs_delete_device_group which deletes these sysfs entries is
called after releasing their metadata file inodes.
Therefore, access to some of these sysfs attributes may occur outside of
the lifetime of these metadata files, resulting in inode NULL pointer
dereferences or use-after-free.
In addition, the call to nilfs_sysfs_create_device_group() is made during
the locking period of the semaphore "ns_sem" of nilfs object, so the
shrinker call caused by the memory allocation for the sysfs entries, may
derive lock dependencies "ns_sem" -> (shrinker) -> "locks acquired in
nilfs_evict_inode()".
Since nilfs2 may acquire "ns_sem" deep in the call stack holding other
locks via its error handler __nilfs_error(), this causes lockdep to report
circular locking. This is a false positive and no circular locking
actually occurs as no inodes exist yet when
nilfs_sysfs_create_device_group() is called. Fortunately, the lockdep
warnings can be resolved by simply moving the call to
nilfs_sysfs_create_device_group() out of "ns_sem".
This fixes these sysfs issues by revising where the device's sysfs
interface is created/deleted and keeping its lifetime within the lifetime
of the metadata files above. |
| In the Linux kernel, the following vulnerability has been resolved:
firewire: net: fix use after free in fwnet_finish_incoming_packet()
The netif_rx() function frees the skb so we can't dereference it to
save the skb->len. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ses: Handle enclosure with just a primary component gracefully
This reverts commit 3fe97ff3d949 ("scsi: ses: Don't attach if enclosure
has no components") and introduces proper handling of case where there are
no detected secondary components, but primary component (enumerated in
num_enclosures) does exist. That fix was originally proposed by Ding Hui
<dinghui@sangfor.com.cn>.
Completely ignoring devices that have one primary enclosure and no
secondary one results in ses_intf_add() bailing completely
scsi 2:0:0:254: enclosure has no enumerated components
scsi 2:0:0:254: Failed to bind enclosure -12ven in valid configurations such
even on valid configurations with 1 primary and 0 secondary enclosures as
below:
# sg_ses /dev/sg0
3PARdata SES 3321
Supported diagnostic pages:
Supported Diagnostic Pages [sdp] [0x0]
Configuration (SES) [cf] [0x1]
Short Enclosure Status (SES) [ses] [0x8]
# sg_ses -p cf /dev/sg0
3PARdata SES 3321
Configuration diagnostic page:
number of secondary subenclosures: 0
generation code: 0x0
enclosure descriptor list
Subenclosure identifier: 0 [primary]
relative ES process id: 0, number of ES processes: 1
number of type descriptor headers: 1
enclosure logical identifier (hex): 20000002ac02068d
enclosure vendor: 3PARdata product: VV rev: 3321
type descriptor header and text list
Element type: Unspecified, subenclosure id: 0
number of possible elements: 1
The changelog for the original fix follows
=====
We can get a crash when disconnecting the iSCSI session,
the call trace like this:
[ffff00002a00fb70] kfree at ffff00000830e224
[ffff00002a00fba0] ses_intf_remove at ffff000001f200e4
[ffff00002a00fbd0] device_del at ffff0000086b6a98
[ffff00002a00fc50] device_unregister at ffff0000086b6d58
[ffff00002a00fc70] __scsi_remove_device at ffff00000870608c
[ffff00002a00fca0] scsi_remove_device at ffff000008706134
[ffff00002a00fcc0] __scsi_remove_target at ffff0000087062e4
[ffff00002a00fd10] scsi_remove_target at ffff0000087064c0
[ffff00002a00fd70] __iscsi_unbind_session at ffff000001c872c4
[ffff00002a00fdb0] process_one_work at ffff00000810f35c
[ffff00002a00fe00] worker_thread at ffff00000810f648
[ffff00002a00fe70] kthread at ffff000008116e98
In ses_intf_add, components count could be 0, and kcalloc 0 size scomp,
but not saved in edev->component[i].scratch
In this situation, edev->component[0].scratch is an invalid pointer,
when kfree it in ses_intf_remove_enclosure, a crash like above would happen
The call trace also could be other random cases when kfree cannot catch
the invalid pointer
We should not use edev->component[] array when the components count is 0
We also need check index when use edev->component[] array in
ses_enclosure_data_process
===== |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: don't check PageError in __extent_writepage
__extent_writepage currenly sets PageError whenever any error happens,
and the also checks for PageError to decide if to call error handling.
This leads to very unclear responsibility for cleaning up on errors.
In the VM and generic writeback helpers the basic idea is that once
I/O is fired off all error handling responsibility is delegated to the
end I/O handler. But if that end I/O handler sets the PageError bit,
and the submitter checks it, the bit could in some cases leak into the
submission context for fast enough I/O.
Fix this by simply not checking PageError and just using the local
ret variable to check for submission errors. This also fundamentally
solves the long problem documented in a comment in __extent_writepage
by never leaking the error bit into the submission context. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix NULL pointer dereference in smb2_get_info_filesystem()
If share is , share->path is NULL and it cause NULL pointer
dereference issue. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: xsk: Fix crash on regular rq reactivation
When the regular rq is reactivated after the XSK socket is closed
it could be reading stale cqes which eventually corrupts the rq.
This leads to no more traffic being received on the regular rq and a
crash on the next close or deactivation of the rq.
Kal Cuttler Conely reported this issue as a crash on the release
path when the xdpsock sample program is stopped (killed) and restarted
in sequence while traffic is running.
This patch flushes all cqes when during the rq flush. The cqe flushing
is done in the reset state of the rq. mlx5e_rq_to_ready code is moved
into the flush function to allow for this. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Fix device management cmd timeout flow
In the UFS error handling flow, the host will send a device management cmd
(NOP OUT) to the device for link recovery. If this cmd times out and
clearing the doorbell fails, ufshcd_wait_for_dev_cmd() will do nothing and
return. hba->dev_cmd.complete struct is not set to NULL.
When this happens, if cmd has been completed by device, then we will call
complete() in __ufshcd_transfer_req_compl(). Because the complete struct is
allocated on the stack, the following crash will occur:
ipanic_die+0x24/0x38 [mrdump]
die+0x344/0x748
arm64_notify_die+0x44/0x104
do_debug_exception+0x104/0x1e0
el1_dbg+0x38/0x54
el1_sync_handler+0x40/0x88
el1_sync+0x8c/0x140
queued_spin_lock_slowpath+0x2e4/0x3c0
__ufshcd_transfer_req_compl+0x3b0/0x1164
ufshcd_trc_handler+0x15c/0x308
ufshcd_host_reset_and_restore+0x54/0x260
ufshcd_reset_and_restore+0x28c/0x57c
ufshcd_err_handler+0xeb8/0x1b6c
process_one_work+0x288/0x964
worker_thread+0x4bc/0xc7c
kthread+0x15c/0x264
ret_from_fork+0x10/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: Reset connection when trying to use SMCRv2 fails.
We found a crash when using SMCRv2 with 2 Mellanox ConnectX-4. It
can be reproduced by:
- smc_run nginx
- smc_run wrk -t 32 -c 500 -d 30 http://<ip>:<port>
BUG: kernel NULL pointer dereference, address: 0000000000000014
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 8000000108713067 P4D 8000000108713067 PUD 151127067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 4 PID: 2441 Comm: kworker/4:249 Kdump: loaded Tainted: G W E 6.4.0-rc1+ #42
Workqueue: smc_hs_wq smc_listen_work [smc]
RIP: 0010:smc_clc_send_confirm_accept+0x284/0x580 [smc]
RSP: 0018:ffffb8294b2d7c78 EFLAGS: 00010a06
RAX: ffff8f1873238880 RBX: ffffb8294b2d7dc8 RCX: 0000000000000000
RDX: 00000000000000b4 RSI: 0000000000000001 RDI: 0000000000b40c00
RBP: ffffb8294b2d7db8 R08: ffff8f1815c5860c R09: 0000000000000000
R10: 0000000000000400 R11: 0000000000000000 R12: ffff8f1846f56180
R13: ffff8f1815c5860c R14: 0000000000000001 R15: 0000000000000001
FS: 0000000000000000(0000) GS:ffff8f1aefd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000014 CR3: 00000001027a0001 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? mlx5_ib_map_mr_sg+0xa1/0xd0 [mlx5_ib]
? smcr_buf_map_link+0x24b/0x290 [smc]
? __smc_buf_create+0x4ee/0x9b0 [smc]
smc_clc_send_accept+0x4c/0xb0 [smc]
smc_listen_work+0x346/0x650 [smc]
? __schedule+0x279/0x820
process_one_work+0x1e5/0x3f0
worker_thread+0x4d/0x2f0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2c/0x50
</TASK>
During the CLC handshake, server sequentially tries available SMCRv2
and SMCRv1 devices in smc_listen_work().
If an SMCRv2 device is found. SMCv2 based link group and link will be
assigned to the connection. Then assumed that some buffer assignment
errors happen later in the CLC handshake, such as RMB registration
failure, server will give up SMCRv2 and try SMCRv1 device instead. But
the resources assigned to the connection won't be reset.
When server tries SMCRv1 device, the connection creation process will
be executed again. Since conn->lnk has been assigned when trying SMCRv2,
it will not be set to the correct SMCRv1 link in
smcr_lgr_conn_assign_link(). So in such situation, conn->lgr points to
correct SMCRv1 link group but conn->lnk points to the SMCRv2 link
mistakenly.
Then in smc_clc_send_confirm_accept(), conn->rmb_desc->mr[link->link_idx]
will be accessed. Since the link->link_idx is not correct, the related
MR may not have been initialized, so crash happens.
| Try SMCRv2 device first
| |-> conn->lgr: assign existed SMCRv2 link group;
| |-> conn->link: assign existed SMCRv2 link (link_idx may be 1 in SMC_LGR_SYMMETRIC);
| |-> sndbuf & RMB creation fails, quit;
|
| Try SMCRv1 device then
| |-> conn->lgr: create SMCRv1 link group and assign;
| |-> conn->link: keep SMCRv2 link mistakenly;
| |-> sndbuf & RMB creation succeed, only RMB->mr[link_idx = 0]
| initialized.
|
| Then smc_clc_send_confirm_accept() accesses
| conn->rmb_desc->mr[conn->link->link_idx, which is 1], then crash.
v
This patch tries to fix this by cleaning conn->lnk before assigning
link. In addition, it is better to reset the connection and clean the
resources assigned if trying SMCRv2 failed in buffer creation or
registration. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: fix leaked reference count of nfsd4_ssc_umount_item
The reference count of nfsd4_ssc_umount_item is not decremented
on error conditions. This prevents the laundromat from unmounting
the vfsmount of the source file.
This patch decrements the reference count of nfsd4_ssc_umount_item
on error. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915/dpt: Treat the DPT BO as a framebuffer
Currently i915_gem_object_is_framebuffer() doesn't treat the
BO containing the framebuffer's DPT as a framebuffer itself.
This means eg. that the shrinker can evict the DPT BO while
leaving the actual FB BO bound, when the DPT is allocated
from regular shmem.
That causes an immediate oops during hibernate as we
try to rewrite the PTEs inside the already evicted
DPT obj.
TODO: presumably this might also be the reason for the
DPT related display faults under heavy memory pressure,
but I'm still not sure how that would happen as the object
should be pinned by intel_dpt_pin() while in active use by
the display engine...
(cherry picked from commit 779cb5ba64ec7df80675a956c9022929514f517a) |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: mpi3mr: Use number of bits to manage bitmap sizes
To allocate bitmaps, the mpi3mr driver calculates sizes of bitmaps using
byte as unit. However, bitmap helper functions assume that bitmaps are
allocated using unsigned long as unit. This gap causes memory access beyond
the bitmap sizes and results in "BUG: KASAN: slab-out-of-bounds". The BUG
was observed at firmware download to eHBA-9600. Call trace indicated that
the out-of-bounds access happened in find_first_zero_bit() called from
mpi3mr_send_event_ack() for miroc->evtack_cmds_bitmap.
To fix the BUG, do not use bytes to manage bitmap sizes. Instead, use
number of bits, and call bitmap helper functions which take number of bits
as arguments. For memory allocation, call bitmap_zalloc() instead of
kzalloc() and krealloc(). For memory free, call bitmap_free() instead of
kfree(). For zero clear, call bitmap_clear() instead of memset().
Remove three fields for bitmap byte sizes in struct scmd_priv which are no
longer required. Replace the field dev_handle_bitmap_sz with
dev_handle_bitmap_bits to keep number of bits of removepend_bitmap across
resize. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_conn: fail SCO/ISO via hci_conn_failed if ACL gone early
Not calling hci_(dis)connect_cfm before deleting conn referred to by a
socket generally results to use-after-free.
When cleaning up SCO connections when the parent ACL is deleted too
early, use hci_conn_failed to do the connection cleanup properly.
We also need to clean up ISO connections in a similar situation when
connecting has started but LE Create CIS is not yet sent, so do it too
here. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: fix a potential overflow in sctp_ifwdtsn_skip
Currently, when traversing ifwdtsn skips with _sctp_walk_ifwdtsn, it only
checks the pos against the end of the chunk. However, the data left for
the last pos may be < sizeof(struct sctp_ifwdtsn_skip), and dereference
it as struct sctp_ifwdtsn_skip may cause coverflow.
This patch fixes it by checking the pos against "the end of the chunk -
sizeof(struct sctp_ifwdtsn_skip)" in sctp_ifwdtsn_skip, similar to
sctp_fwdtsn_skip. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSv4.2: Rework scratch handling for READ_PLUS (again)
I found that the read code might send multiple requests using the same
nfs_pgio_header, but nfs4_proc_read_setup() is only called once. This is
how we ended up occasionally double-freeing the scratch buffer, but also
means we set a NULL pointer but non-zero length to the xdr scratch
buffer. This results in an oops the first time decoding needs to copy
something to scratch, which frequently happens when decoding READ_PLUS
hole segments.
I fix this by moving scratch handling into the pageio read code. I
provide a function to allocate scratch space for decoding read replies,
and free the scratch buffer when the nfs_pgio_header is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix racy issue under cocurrent smb2 tree disconnect
There is UAF issue under cocurrent smb2 tree disconnect.
This patch introduce TREE_CONN_EXPIRE flags for tcon to avoid cocurrent
access. |
