| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Fix pci device refcount leak in ppr_notifier()
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put(). So call it before returning from ppr_notifier()
to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
drbd: only clone bio if we have a backing device
Commit c347a787e34cb (drbd: set ->bi_bdev in drbd_req_new) moved a
bio_set_dev call (which has since been removed) to "earlier", from
drbd_request_prepare to drbd_req_new.
The problem is that this accesses device->ldev->backing_bdev, which is
not NULL-checked at this point. When we don't have an ldev (i.e. when
the DRBD device is diskless), this leads to a null pointer deref.
So, only allocate the private_bio if we actually have a disk. This is
also a small optimization, since we don't clone the bio to only to
immediately free it again in the diskless case. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Validate data run offset
This adds sanity checks for data run offset. We should make sure data
run offset is legit before trying to unpack them, otherwise we may
encounter use-after-free or some unexpected memory access behaviors.
[ 82.940342] BUG: KASAN: use-after-free in run_unpack+0x2e3/0x570
[ 82.941180] Read of size 1 at addr ffff888008a8487f by task mount/240
[ 82.941670]
[ 82.942069] CPU: 0 PID: 240 Comm: mount Not tainted 5.19.0+ #15
[ 82.942482] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[ 82.943720] Call Trace:
[ 82.944204] <TASK>
[ 82.944471] dump_stack_lvl+0x49/0x63
[ 82.944908] print_report.cold+0xf5/0x67b
[ 82.945141] ? __wait_on_bit+0x106/0x120
[ 82.945750] ? run_unpack+0x2e3/0x570
[ 82.946626] kasan_report+0xa7/0x120
[ 82.947046] ? run_unpack+0x2e3/0x570
[ 82.947280] __asan_load1+0x51/0x60
[ 82.947483] run_unpack+0x2e3/0x570
[ 82.947709] ? memcpy+0x4e/0x70
[ 82.947927] ? run_pack+0x7a0/0x7a0
[ 82.948158] run_unpack_ex+0xad/0x3f0
[ 82.948399] ? mi_enum_attr+0x14a/0x200
[ 82.948717] ? run_unpack+0x570/0x570
[ 82.949072] ? ni_enum_attr_ex+0x1b2/0x1c0
[ 82.949332] ? ni_fname_type.part.0+0xd0/0xd0
[ 82.949611] ? mi_read+0x262/0x2c0
[ 82.949970] ? ntfs_cmp_names_cpu+0x125/0x180
[ 82.950249] ntfs_iget5+0x632/0x1870
[ 82.950621] ? ntfs_get_block_bmap+0x70/0x70
[ 82.951192] ? evict+0x223/0x280
[ 82.951525] ? iput.part.0+0x286/0x320
[ 82.951969] ntfs_fill_super+0x1321/0x1e20
[ 82.952436] ? put_ntfs+0x1d0/0x1d0
[ 82.952822] ? vsprintf+0x20/0x20
[ 82.953188] ? mutex_unlock+0x81/0xd0
[ 82.953379] ? set_blocksize+0x95/0x150
[ 82.954001] get_tree_bdev+0x232/0x370
[ 82.954438] ? put_ntfs+0x1d0/0x1d0
[ 82.954700] ntfs_fs_get_tree+0x15/0x20
[ 82.955049] vfs_get_tree+0x4c/0x130
[ 82.955292] path_mount+0x645/0xfd0
[ 82.955615] ? putname+0x80/0xa0
[ 82.955955] ? finish_automount+0x2e0/0x2e0
[ 82.956310] ? kmem_cache_free+0x110/0x390
[ 82.956723] ? putname+0x80/0xa0
[ 82.957023] do_mount+0xd6/0xf0
[ 82.957411] ? path_mount+0xfd0/0xfd0
[ 82.957638] ? __kasan_check_write+0x14/0x20
[ 82.957948] __x64_sys_mount+0xca/0x110
[ 82.958310] do_syscall_64+0x3b/0x90
[ 82.958719] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 82.959341] RIP: 0033:0x7fd0d1ce948a
[ 82.960193] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008
[ 82.961532] RSP: 002b:00007ffe59ff69a8 EFLAGS: 00000202 ORIG_RAX: 00000000000000a5
[ 82.962527] RAX: ffffffffffffffda RBX: 0000564dcc107060 RCX: 00007fd0d1ce948a
[ 82.963266] RDX: 0000564dcc107260 RSI: 0000564dcc1072e0 RDI: 0000564dcc10fce0
[ 82.963686] RBP: 0000000000000000 R08: 0000564dcc107280 R09: 0000000000000020
[ 82.964272] R10: 00000000c0ed0000 R11: 0000000000000202 R12: 0000564dcc10fce0
[ 82.964785] R13: 0000564dcc107260 R14: 0000000000000000 R15: 00000000ffffffff |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt76x0: fix oob access in mt76x0_phy_get_target_power
After 'commit ba45841ca5eb ("wifi: mt76: mt76x02: simplify struct
mt76x02_rate_power")', mt76x02 relies on ht[0-7] rate_power data for
vht mcs{0,7}, while it uses vth[0-1] rate_power for vht mcs {8,9}.
Fix a possible out-of-bound access in mt76x0_phy_get_target_power routine. |
| Improper Verification of Intent by Broadcast Receiver in DeviceIdService prior to SMR Apr-2025 Release 1 allows local attackers to reset OAID. |
| Out-of-bounds write in secfr trustlet prior to SMR Apr-2025 Release 1 allows local privileged attackers to cause memory corruption. |
| KaTeX is a JavaScript library for TeX math rendering on the web. KaTeX users who render untrusted mathematical expressions could encounter malicious input using `\edef` that causes a near-infinite loop, despite setting `maxExpand` to avoid such loops. This can be used as an availability attack, where e.g. a client rendering another user's KaTeX input will be unable to use the site due to memory overflow, tying up the main thread, or stack overflow. Upgrade to KaTeX v0.16.10 to remove this vulnerability. |
| phpMyChat Plus 1.98 contains a SQL injection vulnerability in the deluser.php page through the pmc_username parameter that allows attackers to manipulate database queries. Attackers can exploit boolean-based, error-based, and time-based blind SQL injection techniques to extract sensitive database information by crafting malicious payloads in the username field. |
| A vulnerability was discovered in RISC-V Rocket-Chip v1.6 and before implementation where the SRET (Supervisor-mode Exception Return) instruction fails to correctly transition the processor's privilege level. Instead of downgrading from Machine-mode (M-mode) to Supervisor-mode (S-mode) as specified by the sstatus.SPP bit, the processor incorrectly remains in M-mode, leading to a critical privilege retention vulnerability. |
| In the Linux kernel, the following vulnerability has been resolved:
media: coda: Add check for kmalloc
As the kmalloc may return NULL pointer,
it should be better to check the return value
in order to avoid NULL poineter dereference,
same as the others. |
| A vulnerability was determined in WeKan up to 8.20. This affects an unknown part of the file packages/wekan-ldap/server/syncUser.js of the component LDAP User Sync. This manipulation causes improper access controls. It is possible to initiate the attack remotely. Upgrading to version 8.21 is able to mitigate this issue. Patch name: 146905a459106b5d00b4f09453a6554255e6965a. You should upgrade the affected component. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/smmuv3: Fix hotplug callback leak in arm_smmu_pmu_init()
arm_smmu_pmu_init() won't remove the callback added by
cpuhp_setup_state_multi() when platform_driver_register() failed. Remove
the callback by cpuhp_remove_multi_state() in fail path.
Similar to the handling of arm_ccn_init() in commit 26242b330093 ("bus:
arm-ccn: Prevent hotplug callback leak") |
| In the Linux kernel, the following vulnerability has been resolved:
lib/fonts: fix undefined behavior in bit shift for get_default_font
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in lib/fonts/fonts.c:139:20
left shift of 1 by 31 places cannot be represented in type 'int'
<TASK>
dump_stack_lvl+0x7d/0xa5
dump_stack+0x15/0x1b
ubsan_epilogue+0xe/0x4e
__ubsan_handle_shift_out_of_bounds+0x1e7/0x20c
get_default_font+0x1c7/0x1f0
fbcon_startup+0x347/0x3a0
do_take_over_console+0xce/0x270
do_fbcon_takeover+0xa1/0x170
do_fb_registered+0x2a8/0x340
fbcon_fb_registered+0x47/0xe0
register_framebuffer+0x294/0x4a0
__drm_fb_helper_initial_config_and_unlock+0x43c/0x880 [drm_kms_helper]
drm_fb_helper_initial_config+0x52/0x80 [drm_kms_helper]
drm_fbdev_client_hotplug+0x156/0x1b0 [drm_kms_helper]
drm_fbdev_generic_setup+0xfc/0x290 [drm_kms_helper]
bochs_pci_probe+0x6ca/0x772 [bochs]
local_pci_probe+0x4d/0xb0
pci_device_probe+0x119/0x320
really_probe+0x181/0x550
__driver_probe_device+0xc6/0x220
driver_probe_device+0x32/0x100
__driver_attach+0x195/0x200
bus_for_each_dev+0xbb/0x120
driver_attach+0x27/0x30
bus_add_driver+0x22e/0x2f0
driver_register+0xa9/0x190
__pci_register_driver+0x90/0xa0
bochs_pci_driver_init+0x52/0x1000 [bochs]
do_one_initcall+0x76/0x430
do_init_module+0x61/0x28a
load_module+0x1f82/0x2e50
__do_sys_finit_module+0xf8/0x190
__x64_sys_finit_module+0x23/0x30
do_syscall_64+0x58/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix potential memory leak in ext4_fc_record_regions()
As krealloc may return NULL, in this case 'state->fc_regions' may not be
freed by krealloc, but 'state->fc_regions' already set NULL. Then will
lead to 'state->fc_regions' memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix a potential memory leak in rtw_init_cmd_priv()
In rtw_init_cmd_priv(), if `pcmdpriv->rsp_allocated_buf` is allocated
in failure, then `pcmdpriv->cmd_allocated_buf` will be not properly
released. Besides, considering there are only two error paths and the
first one can directly return, so we do not need implicitly jump to the
`exit` tag to execute the error handler.
So this patch added `kfree(pcmdpriv->cmd_allocated_buf);` on the error
path to release the resource and simplified the return logic of
rtw_init_cmd_priv(). As there is no proper device to test with, no runtime
testing was performed. |
| In the Linux kernel, the following vulnerability has been resolved:
test_firmware: fix memory leak in test_firmware_init()
When misc_register() failed in test_firmware_init(), the memory pointed
by test_fw_config->name is not released. The memory leak information is
as follows:
unreferenced object 0xffff88810a34cb00 (size 32):
comm "insmod", pid 7952, jiffies 4294948236 (age 49.060s)
hex dump (first 32 bytes):
74 65 73 74 2d 66 69 72 6d 77 61 72 65 2e 62 69 test-firmware.bi
6e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 n...............
backtrace:
[<ffffffff81b21fcb>] __kmalloc_node_track_caller+0x4b/0xc0
[<ffffffff81affb96>] kstrndup+0x46/0xc0
[<ffffffffa0403a49>] __test_firmware_config_init+0x29/0x380 [test_firmware]
[<ffffffffa040f068>] 0xffffffffa040f068
[<ffffffff81002c41>] do_one_initcall+0x141/0x780
[<ffffffff816a72c3>] do_init_module+0x1c3/0x630
[<ffffffff816adb9e>] load_module+0x623e/0x76a0
[<ffffffff816af471>] __do_sys_finit_module+0x181/0x240
[<ffffffff89978f99>] do_syscall_64+0x39/0xb0
[<ffffffff89a0008b>] entry_SYSCALL_64_after_hwframe+0x63/0xcd |
| In the Linux kernel, the following vulnerability has been resolved:
blk-mq: fix null pointer dereference in blk_mq_clear_rq_mapping()
Our syzkaller report a null pointer dereference, root cause is
following:
__blk_mq_alloc_map_and_rqs
set->tags[hctx_idx] = blk_mq_alloc_map_and_rqs
blk_mq_alloc_map_and_rqs
blk_mq_alloc_rqs
// failed due to oom
alloc_pages_node
// set->tags[hctx_idx] is still NULL
blk_mq_free_rqs
drv_tags = set->tags[hctx_idx];
// null pointer dereference is triggered
blk_mq_clear_rq_mapping(drv_tags, ...)
This is because commit 63064be150e4 ("blk-mq:
Add blk_mq_alloc_map_and_rqs()") merged the two steps:
1) set->tags[hctx_idx] = blk_mq_alloc_rq_map()
2) blk_mq_alloc_rqs(..., set->tags[hctx_idx])
into one step:
set->tags[hctx_idx] = blk_mq_alloc_map_and_rqs()
Since tags is not initialized yet in this case, fix the problem by
checking if tags is NULL pointer in blk_mq_clear_rq_mapping(). |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: fix an information leak in tipc_topsrv_kern_subscr
Use a 8-byte write to initialize sub.usr_handle in
tipc_topsrv_kern_subscr(), otherwise four bytes remain uninitialized
when issuing setsockopt(..., SOL_TIPC, ...).
This resulted in an infoleak reported by KMSAN when the packet was
received:
=====================================================
BUG: KMSAN: kernel-infoleak in copyout+0xbc/0x100 lib/iov_iter.c:169
instrument_copy_to_user ./include/linux/instrumented.h:121
copyout+0xbc/0x100 lib/iov_iter.c:169
_copy_to_iter+0x5c0/0x20a0 lib/iov_iter.c:527
copy_to_iter ./include/linux/uio.h:176
simple_copy_to_iter+0x64/0xa0 net/core/datagram.c:513
__skb_datagram_iter+0x123/0xdc0 net/core/datagram.c:419
skb_copy_datagram_iter+0x58/0x200 net/core/datagram.c:527
skb_copy_datagram_msg ./include/linux/skbuff.h:3903
packet_recvmsg+0x521/0x1e70 net/packet/af_packet.c:3469
____sys_recvmsg+0x2c4/0x810 net/socket.c:?
___sys_recvmsg+0x217/0x840 net/socket.c:2743
__sys_recvmsg net/socket.c:2773
__do_sys_recvmsg net/socket.c:2783
__se_sys_recvmsg net/socket.c:2780
__x64_sys_recvmsg+0x364/0x540 net/socket.c:2780
do_syscall_x64 arch/x86/entry/common.c:50
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd arch/x86/entry/entry_64.S:120
...
Uninit was stored to memory at:
tipc_sub_subscribe+0x42d/0xb50 net/tipc/subscr.c:156
tipc_conn_rcv_sub+0x246/0x620 net/tipc/topsrv.c:375
tipc_topsrv_kern_subscr+0x2e8/0x400 net/tipc/topsrv.c:579
tipc_group_create+0x4e7/0x7d0 net/tipc/group.c:190
tipc_sk_join+0x2a8/0x770 net/tipc/socket.c:3084
tipc_setsockopt+0xae5/0xe40 net/tipc/socket.c:3201
__sys_setsockopt+0x87f/0xdc0 net/socket.c:2252
__do_sys_setsockopt net/socket.c:2263
__se_sys_setsockopt net/socket.c:2260
__x64_sys_setsockopt+0xe0/0x160 net/socket.c:2260
do_syscall_x64 arch/x86/entry/common.c:50
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd arch/x86/entry/entry_64.S:120
Local variable sub created at:
tipc_topsrv_kern_subscr+0x57/0x400 net/tipc/topsrv.c:562
tipc_group_create+0x4e7/0x7d0 net/tipc/group.c:190
Bytes 84-87 of 88 are uninitialized
Memory access of size 88 starts at ffff88801ed57cd0
Data copied to user address 0000000020000400
...
===================================================== |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: mpt3sas: Fix possible resource leaks in mpt3sas_transport_port_add()
In mpt3sas_transport_port_add(), if sas_rphy_add() returns error,
sas_rphy_free() needs be called to free the resource allocated in
sas_end_device_alloc(). Otherwise a kernel crash will happen:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000108
CPU: 45 PID: 37020 Comm: bash Kdump: loaded Tainted: G W 6.1.0-rc1+ #189
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : device_del+0x54/0x3d0
lr : device_del+0x37c/0x3d0
Call trace:
device_del+0x54/0x3d0
attribute_container_class_device_del+0x28/0x38
transport_remove_classdev+0x6c/0x80
attribute_container_device_trigger+0x108/0x110
transport_remove_device+0x28/0x38
sas_rphy_remove+0x50/0x78 [scsi_transport_sas]
sas_port_delete+0x30/0x148 [scsi_transport_sas]
do_sas_phy_delete+0x78/0x80 [scsi_transport_sas]
device_for_each_child+0x68/0xb0
sas_remove_children+0x30/0x50 [scsi_transport_sas]
sas_rphy_remove+0x38/0x78 [scsi_transport_sas]
sas_port_delete+0x30/0x148 [scsi_transport_sas]
do_sas_phy_delete+0x78/0x80 [scsi_transport_sas]
device_for_each_child+0x68/0xb0
sas_remove_children+0x30/0x50 [scsi_transport_sas]
sas_remove_host+0x20/0x38 [scsi_transport_sas]
scsih_remove+0xd8/0x420 [mpt3sas]
Because transport_add_device() is not called when sas_rphy_add() fails, the
device is not added. When sas_rphy_remove() is subsequently called to
remove the device in the remove() path, a NULL pointer dereference happens. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: mlme: fix null-ptr deref on failed assoc
If association to an AP without a link 0 fails, then we crash in
tracing because it assumes that either ap_mld_addr or link 0 BSS
is valid, since we clear sdata->vif.valid_links and then don't
add the ap_mld_addr to the struct.
Since we clear also sdata->vif.cfg.ap_addr, keep a local copy of
it and assign it earlier, before clearing valid_links, to fix
this. |
